Nissan 370Z Forum

370Z Forums HOME

My Picture Album

Nissan 370Z Pictures

Premium Membership

Become a Forum Sponsor

		Nissan 370Z Forum > Members List
RDWizard's Profile

RDWizard is on a distinguished road

RDWizard

Base Member

Last Activity: 08-18-2020 12:04 PM

About Me

About RDWizard

Location

Mansfield, TX

Drives

12 Nissan 370Z MB M6

Statistics

Total Posts

General Information

Last Activity: 08-18-2020 12:04 PM
Join Date: 09-06-2015
Referrals: 0

Likes Given

8 Likes

RDWizard liked post by Jhill On thread : Stft

Interesting article, I’ve never done it that way but you may want to reread it. It states if your stft does not go over 15% then you are looking at ignition related, if it does go over 15% and into...
Liked On: 03-10-2018, 07:32 PM
Posted On: 03-10-2018, 03:11 PM
RDWizard liked post by ZWorks On thread : VVT Solenoids

i got a pair, txt me 630 800 8304
Liked On: 02-11-2018, 06:57 PM
Posted On: 02-11-2018, 06:28 PM
RDWizard liked post by stansens On thread : VVT Camshaft Sprocket Phaser check

So all of that unburned gas diluted the engine oil which means a lot could evaporate via engine heat. All of that raw fuel into cylinder six would compromise the seal that the oil rings could give...
Liked On: 02-06-2018, 03:37 PM
Posted On: 02-06-2018, 03:35 PM
RDWizard liked post by Spooler On thread : VVT Camshaft Sprocket Phaser check

Good deal, sounds like the engine is fine. Wiring is the next place to look. Sounds like you may have broken wire in the harness. It happens.
Liked On: 02-05-2018, 12:35 PM
Posted On: 02-05-2018, 12:34 PM
RDWizard liked post by Streetz On thread : VVT Camshaft Sprocket Phaser check

Need to check the operation of the phaser. You can command it to a specific degree with a scan tool. If the phaser doesn't work when being commanded its either the cam phaser solenoid or the phaser....
Liked On: 02-03-2018, 06:33 AM
Posted On: 02-02-2018, 12:40 PM
RDWizard liked post by phunk On thread : How to do TDC and correct timing

^^ exactly, there is no purpose to spinning the engine until the timing chain marks are aligned. Just make sure cylinder 1 is TDC and you are safe to take it apart. The colored links on the chain...
Liked On: 01-25-2018, 04:19 PM
Posted On: 01-25-2018, 03:36 PM
RDWizard liked post by TechnicZ On thread : How to do TDC and correct timing

Whenever you're are removing a timing chain or belt. You always need to bring cylinder 1 to top dead center. There are timing marks when you remove the timing cover stamped onto the cams and...
Liked On: 01-25-2018, 04:16 PM
Posted On: 01-25-2018, 03:29 PM
RDWizard liked post by phunk On thread : How to do TDC and correct timing

My formula fell on deaf ears :( Where x = timing chain links, and y = crank sprocket teeth lcm(x,y) / y = revolutions between timing chain eclipse solution: lcm(100,24) / 24 = 100 revolutions...
Liked On: 01-25-2018, 04:00 PM
Posted On: 01-25-2018, 02:13 PM

Mini Statistics

Join Date: 09-06-2015
Total Posts: 20
Likes Received: 10
Likes Given: 8

Show All Statistics

Recent Visitors

The last 9 visitor(s) to this page were:

This page has had 1,192 visits

All times are GMT -5. The time now is 02:56 AM.