Pro4Jackster

Base Member

Last Activity: 08-03-2017 03:40 PM

About Me

About Pro4Jackster

Location

NW Houston

Drives

'08 350Z
Signature
Jtranbuilt '08 Z [Jtran PT7075 Single - Fujitsubo - Transgo - Wilwood - TE37SL - BC Racing]

Statistics

Total Posts

Total Posts: 130
Posts Per Day: 0.03
Find all posts by Pro4Jackster
Find all threads started by Pro4Jackster

General Information

Last Activity: 08-03-2017 03:40 PM
Join Date: 10-22-2011
Referrals: 0

Friends

Showing Friends 1 to 1 of 1

Nut_N_Much

A True Z Fanatic

Likes Given

38 Likes

Pro4Jackster liked post by Mr.Squeeze On thread : Nut_N_Much Journal

:tup: That's a nice adjustment you made, 2A033-030 35 MM is the one that I used it fits better either way nice job.
Liked On: 06-08-2013, 02:50 AM
Posted On: 05-04-2013, 07:19 PM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

Man I wish I could but the weird thing is that its the only thing holding your upper A-Arm in place. Strange isn't it. That little tab and bolt hold the hole left side of the upper A-Arm in place. ...
Liked On: 06-08-2013, 02:49 AM
Posted On: 05-04-2013, 03:45 PM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

Update: I didn't spend much time on the car today but I did get some stuff done. All the hoses are built and routed. While I was finishing up the pump hose the Fed Ex truck pulled up.. He...
Liked On: 06-08-2013, 02:49 AM
Posted On: 05-03-2013, 03:54 PM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

32 tooth.. Are you doing an impeller swap? :tiphat:
Liked On: 06-08-2013, 02:48 AM
Posted On: 05-25-2013, 06:57 AM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

No sir, the idler pulley is for the serpentine belt that runs Alt, Water pump etc. on the front of the motor. I just had to order it from Stillen because it mounts to the SC plate and of course the...
Liked On: 06-08-2013, 02:48 AM
Posted On: 05-24-2013, 10:10 AM
Pro4Jackster liked post by Mr.Squeeze On thread : Nut_N_Much Journal

With the added brace you should be fine I dont think you will have a problem at all. I found a picture laying around of the 35mm cog before I sold it I think other people that tried had the standard...
Liked On: 06-08-2013, 02:08 AM
Posted On: 05-08-2013, 08:28 PM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

When you install the SC on to the motor the idler pulley on the back of the flex plate needs to clear the engine block. I had a Jack Shaft of 34 and SC Drive of 32 but when you put the belt on there...
Liked On: 06-08-2013, 02:06 AM
Posted On: 06-03-2013, 09:01 AM
Pro4Jackster liked post by Nut_N_Much On thread : Nut_N_Much Journal

We have a tuner in Tampa named Martin. He has cracked the code for 7AT line pressures. When you get ready to tune let me know and you can see if Martin would send your tuner the MAP. Sounds like a...
Liked On: 06-08-2013, 02:05 AM
Posted On: 06-04-2013, 06:23 PM

Page 3 of 3

Pro4Jackster

Base Member

About Me

Statistics

Friends

Likes Given

Mini Statistics

Friends

Recent Visitors

	Nut_N_Much A True Z Fanatic