Knio

Base Member

Last Activity: 10-19-2024 07:14 PM

About Me

About Knio

Location

Palo Alto, CA

Drives

40th

Statistics

Total Posts

Total Posts: 141
Posts Per Day: 0.03
Find all posts by Knio
Find all threads started by Knio

Albums

Total Albums: 2
Total Pictures: 10
Albums Created by Knio

General Information

Last Activity: 10-19-2024 07:14 PM
Join Date: 05-24-2011
Referrals: 0

Friends

Showing Friends 1 to 4 of 4

bigdog1250

Track Member
DIGItonium

A True Z Fanatic
FricFrac

A True Z Fanatic
Jmg90300zx

Base Member

Likes Given

69 Likes

Knio liked post by RDWizard On thread : VVT Camshaft Sprocket Phaser check

So the plot thickens!!!! Compression check is good. 225psi. I have been resetting the ECU at the beginning of every test I do. Still getting P0011 & P0300/P0306 codes and going into limp mode...
Liked On: 01-12-2020, 11:51 PM
Posted On: 02-05-2018, 08:13 AM
Knio liked post by SouthArk370Z On thread : NST Pulley Install - Crankshaft bolt stuck?

FWIW, one can bypass the starting system by unplugging the "S" connector from the backside of the starter and applying 12V to the wire going to the starter solenoid when you want the starter to spin....
Liked On: 01-02-2020, 06:21 PM
Posted On: 12-02-2012, 05:14 PM
Knio liked post by Megan370z On thread : NST Pulley Install - Crankshaft bolt stuck?

that bolt can be extremely hard to remove , dont worry you wont break the bolt unless you absolutely have to use an 1''inch breaker bar if nothing else worked then it might snap. I had to use PB...
Liked On: 01-02-2020, 06:20 PM
Posted On: 12-02-2012, 11:00 AM
Knio liked post by BettyZ On thread : P0340

If you dont have some pry bars definitely invest in some. And a breaker bar / 4 foot length of pipe so you can cheater bar the crank pulley bolt. Also depending on whose kit you bought, some...
Liked On: 12-19-2019, 01:06 PM
Posted On: 12-18-2019, 04:08 PM
Knio liked post by SteveSAS On thread : P0340

Have fun cleaning the grey RTV silicone off. There is also the acc. Drive belt. Be careful no to damage mating surfaces when removing cover. Read FSM on how to remove timing cover without...
Liked On: 12-18-2019, 09:12 PM
Posted On: 12-18-2019, 02:17 PM
Knio liked post by faplifesmitty On thread : Crank sensor problems

I recently had a similar issue. My car only started with the cam sensor unplugged and drove around fine in limp mode. The dealership closest to me has repeatedly screwed me over, so I decided to...
Liked On: 12-14-2019, 02:58 AM
Posted On: 08-10-2017, 11:51 PM
Knio liked post by RDWizard On thread : VVT Camshaft Sprocket Phaser check

So I found some interesting information while researching the dreaded P0011 DTC. In the FSM EM-107 step 5 of the Inspection of Camshaft Sprocket (INT) Oil Groove, it mentions that there is an oil...
Liked On: 12-14-2019, 02:53 AM
Posted On: 02-11-2018, 11:48 AM
Knio liked post by stansens On thread : VVT Camshaft Sprocket Phaser check

So all of that unburned gas diluted the engine oil which means a lot could evaporate via engine heat. All of that raw fuel into cylinder six would compromise the seal that the oil rings could give...
Liked On: 12-14-2019, 02:52 AM
Posted On: 02-06-2018, 03:35 PM
Knio liked post by Streetz On thread : VVT Camshaft Sprocket Phaser check

Need to check the operation of the phaser. You can command it to a specific degree with a scan tool. If the phaser doesn't work when being commanded its either the cam phaser solenoid or the phaser....
Liked On: 12-14-2019, 02:51 AM
Posted On: 02-02-2018, 12:40 PM
Knio liked post by RDWizard On thread : VVT Camshaft Sprocket Phaser check

Short story: Car had been throwing a P0300 for a week. Replaced the spark plugs. Car was apparently low on oil from the last oil change at the service center. Less than a quart in the pan. (I...
Liked On: 12-14-2019, 02:50 AM
Posted On: 02-01-2018, 08:51 PM
Knio liked post by omgzmbz On thread : ATTENTION!! 2009-2010 owners with steering lock/wont start issues

My husband ran into this with the 2010 370z he just bought. He couldn't get it out of lock mode and he made a video of his fix for this: pLPTNm0xxy4
Liked On: 11-03-2019, 12:11 AM
Posted On: 12-21-2017, 09:26 AM
Knio liked post by lumpia.z On thread : ATTENTION!! 2009-2010 owners with steering lock/wont start issues

IF ANY OF YALL ARE STUCK ON "LOCK" AND CANT EVEN GET TO ACCESSORY/IGNITION here's my way of solving it: The way I fixed it and got my car back running was just simply hotwiring the damn thing...
Liked On: 11-03-2019, 12:07 AM
Posted On: 01-09-2019, 03:34 PM
Knio liked post by Hotrodz On thread : Update: Steering Lock issue - Bypass Kit!

Just Google 370z steering lock lock fix and there are several videos that will help you out. Mine was supposedly fixed under warranty and I it locked up on me this past winter so I just Googled it...
Liked On: 11-02-2019, 11:46 PM
Posted On: 06-03-2018, 11:27 AM
Knio liked post by dts3 On thread : 370Z CAN Bus Proprietary PID's

I made a run and pulled some CAN data for 10 minutes while driving, and sure enough I get the tire pressures on 0x385. Thanks for the tip!
Liked On: 10-15-2018, 07:15 PM
Posted On: 10-11-2018, 09:34 PM
Knio liked post by Aramis76 On thread : Home Garage Lifting Options - My Lift Stand

Atlas Kwik Bay 7000lbs A little more expensive, but quite versatile and since I actually park on it, it's completely out of the way (no posts) ...
Liked On: 06-25-2017, 11:59 PM
Posted On: 06-24-2017, 02:54 PM

Page 2 of 5

Last »

Knio

Base Member

About Me

Statistics

Friends

Likes Given

Mini Statistics

Friends

Albums

Recent Visitors

	bigdog1250 Track Member

	DIGItonium A True Z Fanatic

	FricFrac A True Z Fanatic