fryzia23

Hey sorry to bother you did your driveshaft do the same thing as mine?

been good bro, getting into autox more this year lol....i need to get an oil cooler and new brakes before i tried to tackle any track, hopefully soon i can have that done to do it

We should try to meet up one day and do a cruise, haven't really planned anything much this past few years lol but now theres more Z's so lets see

Hey bro! how you been? There's an autox event next saturday in meadowlands you should come thru

yeah there is one on the 6th next saturday but I cant make it unfortunately. If you wanna go to the one on the 14 make sure you register asap bc its limited to 80 cars and may fill up soon. MSNE/BMW club are doing the event together. Go to this website, make the account, add your car and register for MSNE event.
MotorSports North East ( MSNE ) - Autocross - HPDE -

oh crap you are right lol, i looked at the wrong dates hahaha, i know theres one in metlife next saturday but didn't know there was one on sunday the 14 as well

Actually I went to AC last weekend for an autox event lol...That was my first time doing it and now i'm "hooked" lol there's going to be one next week in AC again on Sunday, that I'm planning on going. Lets go bro! I'm going to post it to see if we get more Z's to come like you said

hey bro! haven't seen you in a while lol...you should come to our bear mountain cruise this saturday, we're doing it with the NJ Z Car Club

Hey! I just saw u answer me lol I don't get notifications if u write on ur own wall hahaha...it was a nice to meet u bro! Let us know when they have those meets on Thursday!

at meadowlands nissan right? Yeah that was my car

Nice car! did you went to the Z Club car show back in September 2013? I think I saw a car like it before lol

These codes are for downstream/secondary oxygen sensors that are responsible for monitoring a proper functioning catalytic converters. You have HFC and those usually will throw codes periodically....

I have pretty much same clutch setup with v1 HD CSC but stage 3 along with GTM supercharger. When I used to run rbf 600, my clutch would get very soft during some NYC traffic and would get softer on...

Was recommended to use a arp stretch gauge to tighten the rod bearing bolts. I had no prior experience with that tool. It was pretty tough to use it because of limited space. The #5 rod bearing...

Maybe I should give an update. She’s still running! Unfortunately my own engine build didn’t last and it failed. Turned out to be my own fault and mistake I made during assembly. I take that as a...

Was recommended to use a arp stretch gauge to tighten the rod bearing bolts. I had no prior experience with that tool. It was pretty tough to use it because of limited space. The #5 rod bearing...

Maybe I should give an update. She’s still running! Unfortunately my own engine build didn’t last and it failed. Turned out to be my own fault and mistake I made during assembly. I take that as a...

Maybe I should give an update. She’s still running! Unfortunately my own engine build didn’t last and it failed. Turned out to be my own fault and mistake I made during assembly. I take that as a...

Maybe I should give an update. She’s still running! Unfortunately my own engine build didn’t last and it failed. Turned out to be my own fault and mistake I made during assembly. I take that as a...

So dyno session went pretty well. Switched to ecutek and upped the limiter to 7800 RPM. It was about 98F out and was down 3lbs of boost due to ati pulley. Was bummed out a little bit on lower power...

Basically long block is assembled. Just left is the VVEL control solenoid and lower oil pan as its still on the blown engine. JWT valve spring compressor is well worth the money. Now need to push the...

The lift I installed and workshop space addition

Finally started my new engine build after I blew my original exactly a year ago at the track. It took so long because had to build my garage first to accommodate the build and on top of everything...

It's been a while but went out for a track day at NJMP Lightning this weekend. Did my personal best NJMP Lightning Fryzia23 | Arek Fryzlewicz | Michelin Slick Scrubs | 1:11.68 ...

Matched new belt without ac compressor. Engine is basically ready to go up but still waiting on ATI super damper crank pulley. Original shipping date was May 1st and updated date is May 31st so...

Finally started my new engine build after I blew my original exactly a year ago at the track. It took so long because had to build my garage first to accommodate the build and on top of everything...