Beautiful car man! Thanks for the ideas!!!!! Looking at blacking my car out like that as well, keep up the good work!
|
|
LinkBack | Thread Tools | Display Modes |
08-04-2014, 06:10 PM | #49 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
|
08-04-2014, 07:40 PM | #50 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
Quick test fit. Fits very well. Needed some trimming on the inside because of my oil cooler. They also have about a 4"x4" opening for the drain plug, but with my adapter plate and larger filter, I'll have to make a larger opening. The FRP cuts like butter. I also have to move my HID fogs in a bit to clear the opening.
Last edited by pfdaxe; 08-07-2014 at 11:14 AM. |
08-06-2014, 12:02 PM | #51 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
Well, many of you know there's an issue with the hole in the skid plate being too small to change oil (unless you want to remove bumper every time). The hole is just large enough to get to the plug, but not the filter. I hadn't seen any pics of what it looked like so I decided to snap a few for reference. After I made the hole larger, I test fit the bumper and the hole was perfect size to drain oil and replace filter with my thermo plate.
Last edited by pfdaxe; 08-10-2014 at 02:19 PM. |
08-06-2014, 10:02 PM | #53 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
|
08-09-2014, 04:23 PM | #56 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
CF GTR Hood Vents
Tools to use:
Measured & masked off. I also had a towel covering the engine underneath: A couple of pilot holes and then the cutting begins: Test fitting: I sealed and ran a tight bead of body color filler around edge since fitment in the rear is actually not very good. Doesn't completely sit flush back there: |
08-10-2014, 08:21 AM | #58 (permalink) |
A True Z Fanatic
Join Date: Apr 2012
Location: SoCal
Posts: 6,235
Drives: WELL ZED PW 6MT
Rep Power: 53241 |
I agree. Nice work.
__________________
>MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete
|
08-10-2014, 02:23 PM | #60 (permalink) |
A True Z Fanatic
Join Date: Aug 2012
Location: Phoenix, AZ
Posts: 1,067
Drives: 09 Touring AT Sport
Rep Power: 16 |
Some quick finished pics
Bumper still needs to be color sanded (to give the color some depth) since didn't have time prior to install:
Small Diamond Mesh: Large Powder Coated Diamond Mesh: Last edited by pfdaxe; 08-10-2014 at 02:26 PM. |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Which HFC for a TT or SC Build | swiss370Z | Forced Induction | 21 | 09-11-2012 09:10 AM |
Possible Nos build | triadz | Forced Induction | 7 | 04-06-2012 11:30 AM |
TT build in Fl | travnflorida | Nissan 370Z General Discussions | 3 | 08-15-2011 06:51 PM |
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD | Reaper42 | Forced Induction | 14 | 01-22-2011 06:24 PM |
Datsun Roadster 1600...To build or not to build | motoextreme | The Lounge (Off Topic) | 66 | 02-13-2010 01:40 AM |