Diabel's Boosted Performance Single Turbo Build

Meulen · 07-21-2015, 10:40 AM

Quote:

Originally Posted by Diabel

Why do you think it should cross at 5250? Please remember that here in Europe we use Nm instead of ft/tq as a torque unit (left Y axis - blue curve). It was measured on the dyno at 6th gear.

Here in Europe?

Location = Bensonville, IL ???

Diabel · 07-21-2015, 11:12 AM

Quote:

Originally Posted by Chuck33079

Also, why 6th gear?

To make sure the traction will be good, on 5th the car slips on the dyno rolls.

Quote:

Originally Posted by Meulen

Here in Europe?

Location = Bensonville, IL ???

When I visit usa I stay in IL

But currently in Europe, Poland to be more precise

Chuck33079 · 07-21-2015, 11:14 AM

Quote:

Originally Posted by Diabel

To make sure the traction will be good, on 5th the car slips on the dyno rolls.

Wow.

Boosted Performance · 07-21-2015, 12:23 PM

Quote:

Originally Posted by Diabel

Sure, here it is. The car is tuned only at 10% ethanol. I think the 6266 turbo is max out at the moment. The only work left to do is VVEL tune to make the torque more flat at higher RPMs. Also maybe there are some gain possibilities in better headers (currently OEMs) and 3-3,5" exhaust (currently 2,5").

Just today I noticed Ecutek released the new software - I think it may be the game changer (VVEL, No lift shift, Flex fuel).

The 1.15 a/r turbine is maxed out, but the compressor should have more left in it. If you go with a 1.32 a/r turbine housing and keep the 18psi, there is a very good chance you would get over 700whp. It is the turbine that is choking the system...the 1.32 a/r would flatten out that HP after 6,000rpm, and it would help with the torque. Probably about $300 shipped to you if you choose to go with that.

Diabel · 07-22-2015, 08:00 AM

Quote:

Originally Posted by Boosted Performance

The 1.15 a/r turbine is maxed out, but the compressor should have more left in it. If you go with a 1.32 a/r turbine housing and keep the 18psi, there is a very good chance you would get over 700whp. It is the turbine that is choking the system...the 1.32 a/r would flatten out that HP after 6,000rpm, and it would help with the torque. Probably about $300 shipped to you if you choose to go with that.

Sasha, what do you recommend, that 1.32 a/r compressor in 6266 to unchoke it or the new, bigger 6766 turbo? Because after 300usd upgrade the cost of both would be pretty much the same.

jwick · 07-22-2015, 09:50 AM

Unless you are V2.0 make sure you get it with the E compressor cover. That S cover is going to fit without the manifold change

Boosted Performance · 07-22-2015, 03:04 PM

Quote:

Originally Posted by Diabel

Sasha, what do you recommend, that 1.32 a/r compressor in 6266 to unchoke it or the new, bigger 6766 turbo? Because after 300usd upgrade the cost of both would be pretty much the same.

Just upgrade the the turbine to a 1.32 a/r...that is all. I wouldn't worry about going to the 6766 unless you want to really push things to the limit.

Quote:

Originally Posted by jwick

Unless you are V2.0 make sure you get it with the E compressor cover. That S cover is going to fit without the manifold change

Correct, the S compressor cover works only on the V 2.0 of the kit, which includes a change of the manifold. He has the V 1.0 of the kit, with the modified E compressor cover. So to switch to a 6766, the new compressor cover would have to be modified.

Diabel · 07-23-2015, 05:48 AM

Quote:

Originally Posted by Boosted Performance

Just upgrade the the turbine to a 1.32 a/r...that is all. I wouldn't worry about going to the 6766 unless you want to really push things to the limit.

Ok, but what about the turbo lag after that kind of upgrade ftom 1.15 to 1.32? Wouldn't that be a significant increase in the lag?

Quote:

Originally Posted by Boosted Performance

Correct, the S compressor cover works only on the V 2.0 of the kit, which includes a change of the manifold. He has the V 1.0 of the kit, with the modified E compressor cover. So to switch to a 6766, the new compressor cover would have to be modified.

I've already upgraded the turbine to S cover and I've changed the manifold.

whiteZ34 · 01-04-2016, 04:58 PM

Quote:

Originally Posted by Diabel

Sure, here it is. The car is tuned only at 10% ethanol. I think the 6266 turbo is max out at the moment. The only work left to do is VVEL tune to make the torque more flat at higher RPMs. Also maybe there are some gain possibilities in better headers (currently OEMs) and 3-3,5" exhaust (currently 2,5").

Just today I noticed Ecutek released the new software - I think it may be the game changer (VVEL, No lift shift, Flex fuel).

I had just recently seen your build thread and congrats to you sir on some nice numbers.

also wanted to say that my build is closely resembles yours. I have a built motor with Wiesel 9:1 bored .020 over and eagle rods.. I'm hoping to see the same numbers or more towards 700...but I also have z1 headers and I'm changing to the 6766 so I don't run out of breath. Also going with 1000cc injectors and possible twin pump. Going with a custom 3.5" down pipe with a fast intentions 3" duel. I also have Sasha's 3" maf pipes instead of the 2.75..Ecutek is also another mod I will be getting as well. I hope to see what numbers in the spring that this will bring. I also say best of luck to you sir. Any possible feed back you may be able to supply? Thank you, mark

Boosted Performance · 01-07-2016, 09:46 AM

Mike, PM box is full.

Diabel · 02-05-2016, 10:49 AM

Ok, time for some update.

We've made additional mods:

- 3,5" downpipe
- 3" exhaust four tips
- 1.32 AR for pt6766
- have some troubles with exhaust wheel shaft which damaged, have to buy the new one:

Diabel · 02-05-2016, 10:55 AM

Exhaust mods:

whiteZ34 · 02-05-2016, 10:56 AM

Your 3.5" dp, how'd it fit? Did you copy the original design? I've been looking to do it but can't find anyone to make it..I stand corrected, you posted pics before I got to reply haha

Diabel · 02-05-2016, 11:00 AM

Here are the bumper mods:

Diabel · 02-05-2016, 11:02 AM

And finally, the dyno chart:

1.15 AR 2,5" exhaust + 3"downpipe vs 1.32 AR with 3" exhaust + 3,5" downpipe

07-22-2015, 09:50 AM	#81 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	Unless you are V2.0 make sure you get it with the E compressor cover. That S cover is going to fit without the manifold change __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

01-07-2016, 09:46 AM	#85 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	Mike, PM box is full. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

02-05-2016, 10:55 AM	#87 (permalink)
Diabel Base Member Join Date: Sep 2012 Location: Bensenville IL Posts: 103 Drives: 370z Rep Power: 13	Exhaust mods: Stright_Drop, carlitos_370z and EliteXpress like this. __________________ Built motor, BP kit, safe 17.5-18 PSI, 720WHP, 680 ft/lb, build thread: Fairlady 370z Turbo \| Facebook FanPage of the Car: Movies, Dynos

02-05-2016, 10:56 AM	#88 (permalink)
whiteZ34 Base Member Join Date: May 2013 Location: Pittsburgh Age: 32 Posts: 217 Drives: 2012 Boosted 370z Rep Power: 12	Your 3.5" dp, how'd it fit? Did you copy the original design? I've been looking to do it but can't find anyone to make it..I stand corrected, you posted pics before I got to reply haha Diabel likes this. __________________ R/T Built motor, wiseco 9:1 Pistons, Eagle H-beam rods, ARP L-19\| BP kit, PTE 6766, EPS 70mm TB, GTR Intake, PRS lower conversion\| ID1000cc, CJM Twin pump 340&255, PRS Rails, CJM fuel return\| Fast Intentions\| R/T Tuned, 660WHP 596WTQ at 18lbs. 93 octane

02-05-2016, 11:00 AM	#89 (permalink)
Diabel Base Member Join Date: Sep 2012 Location: Bensenville IL Posts: 103 Drives: 370z Rep Power: 13	Here are the bumper mods: whiteZ34, carlitos_370z and ZontheRocks like this. __________________ Built motor, BP kit, safe 17.5-18 PSI, 720WHP, 680 ft/lb, build thread: Fairlady 370z Turbo \| Facebook FanPage of the Car: Movies, Dynos

02-05-2016, 11:02 AM	#90 (permalink)
Diabel Base Member Join Date: Sep 2012 Location: Bensenville IL Posts: 103 Drives: 370z Rep Power: 13	And finally, the dyno chart: 1.15 AR 2,5" exhaust + 3"downpipe vs 1.32 AR with 3" exhaust + 3,5" downpipe Stright_Drop, whiteZ34 and EliteXpress like this. __________________ Built motor, BP kit, safe 17.5-18 PSI, 720WHP, 680 ft/lb, build thread: Fairlady 370z Turbo \| Facebook FanPage of the Car: Movies, Dynos

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance turbo kit self install (review)	Cell	Forced Induction	87	10-24-2017 10:38 AM
Boosted Performance single turbo build	Boosted Performance	Forced Induction	1841	09-06-2016 12:17 PM
Boosted Performance single turbo results	Boosted Performance	Forced Induction	136	06-18-2014 06:40 PM
>>>>>Puckshaw's Boosted Performance Twin Scroll Single Turbo Build<<<<<	puckshaw	Member's 370Z Gallery	245	05-24-2014 04:13 PM
Single turbo build	jlask370	Forced Induction	13	10-07-2013 01:41 PM