cv129's slow build

cv129 · 09-20-2015, 03:38 PM

Also added 13mm spacers and ARP extended studs. Studs were trimmed back to length, I wanted to retain the stock look and the stock lug nuts.

Front tires are 265/35/19. Rear tires are 285/35/19. Stock alignment.

Rusty · 09-20-2015, 07:41 PM

Quote:

Originally Posted by cv129

ZSpeed aluminum undershroud is finally here!

Stock undershroud was getting beat up. Homemade fix until the new undershroud arrived. The middle three clips wouldn't hold any more. Sealed off all holes to prevent flapping noise from bad air flow.

One bad thing about the stock plastic shield is its elasticity. When heated up (engine heat, Texas summer), and the middle three clips not holding any more, the shield will sag with the middle section hanging quite low. You can see my home made fix was taking a beating.

Nice. You need to do my fix. PM me your address, and I ship you a couple of the nuts, when I get home next week.

Fix for the rattling front under tray.

edzilla123 · 01-31-2016, 01:49 PM

Did they have a 285/30/19 ? would have been pretty close in side wall hight with a 30 i believe

cv129 · 06-01-2016, 02:50 PM

Quote:

Originally Posted by Rusty

Nice. You need to do my fix. PM me your address, and I ship you a couple of the nuts, when I get home next week.

Fix for the rattling front under tray.

Rusty's contribution deserves its own post!

Got these quite some time ago, just never posted it up. Thanks Rusty

cv129 · 06-01-2016, 03:01 PM

RacingBrake rotors. Bought from Mr. Synolimit. Protective coating still on.

Whiteline diff bushings. Bought two sets of these, first set already went on wife's car (OEM bushing busted at 40k miles). Car feels great now

cv129 · 06-01-2016, 03:09 PM

ARK R-Spec TP. Used, from Mr. pRoJeKTxZ. Can't wait to un-chock the VQ!

cv129 · 06-01-2016, 03:13 PM

Shiny oil pan!!!! CJ Motorsports baffled oil pan. Bought from Mr. DR_ .

Rusty · 06-01-2016, 03:33 PM

Quote:

Originally Posted by cv129

Rusty's contribution deserves its own post!

Got these quite some time ago, just never posted it up. Thanks Rusty

Did you get these installed yet?

You'll like the Racing Brake rotors. If you look at the rotor rings. You will see a dimple where they checked the hardness on them.

cv129 · 06-01-2016, 03:39 PM

^ nah not yet....I know, this "build" is slow as snail haha.

httorihanzo · 09-24-2016, 05:20 PM

would love to know brand of these .they arent on vorshlags site

Quote:

Originally Posted by cv129

Beauty shots of arms and coilovers

Things that came out

I took some pics myself in my living room, but theirs are much nicer

KE_1508 · 01-26-2017, 05:58 PM

Nice Nismo!

06-01-2016, 03:39 PM	#39 (permalink)
cv129 A True Z Fanatic Join Date: Jul 2011 Location: Dallas, TX Posts: 3,222 Drives: 09 Nismo, 16 Nismo Rep Power: 163995	^ nah not yet....I know, this "build" is slow as snail haha. __________________ Setrab \| RE-71 \| SPL \| JRZ \| Nismo \| ARK \| Whiteline \| RacingBrake \| CJM Oil Pan \| Ti shield

01-26-2017, 05:58 PM	#41 (permalink)
KE_1508 Base Member Join Date: Dec 2016 Location: AZ/GA Posts: 72 Drives: 08 Nismo 350Z # 1508 Rep Power: 8	Nice Nismo! cv129 likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I have got to slow down!!	bigaudiofanat	The Lounge (Off Topic)	42	05-18-2012 07:46 PM
Why So Slow???	40TH4ME	Audio & Video	4	05-10-2012 11:32 AM
Rev Comes Down Slow?	pa19103	Engine & Drivetrain	4	08-05-2011 12:11 AM
Slow shipping slow response slow everything	thispecialk	Nissan 370Z General Discussions	15	11-01-2010 09:23 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 01:40 AM

01-31-2016, 01:49 PM	#33 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 11	Did they have a 285/30/19 ? would have been pretty close in side wall hight with a 30 i believe