![]() |
My CAI will probably be on sale very soon Im unable to re-install them since my new radiator setup is in the way !! To have the full advantage of
|
![]() |
|
LinkBack | Thread Tools | Display Modes |
|
![]() |
#1 (permalink) |
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
My CAI will probably be on sale very soon
![]() Im unable to re-install them since my new radiator setup is in the way !! To have the full advantage of them, your best bet is to have your TB ported the way I did and ofcourse a Tune will be required. another big reason why I didnt try to make the CAI to fit is Im going with another setup ![]() |
![]() |
![]() |
#2 (permalink) | |
Track Member
Join Date: Feb 2012
Location: St. Louis, MO
Posts: 789
Drives: '09 370Z RAE 6MT
Rep Power: 15 ![]() ![]() |
![]() Quote:
How did you bore your throttle bodies for it?
__________________
( Click to show/hide )
|
|
![]() |
![]() |
#3 (permalink) |
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Yup, mandrel bent start at 3'' that goes to a reducer down to 63.5mm for the MAF sensor then after, it gets streched to 2 3/4'' to the Throttle body.
There is a long straight after the bent that goes up to the TB and MAF sensor to help keeping a laminar flow and not turbulent like what I have seen on some aftermarket CAI. There is ofcourse cutting to do and bending tabs. simiar to when you install the Stillen Ver3 CAI. It wasnt made for look, the black paint that I sprayed on it 2 years ago is all scrached over. there isnt any bracket support since 2x Tie-wrap was good enough with rubber pads to avoid rubbing. ( I used cutted hose as pads) I cant provide any PCV tubing since I had to reuse my original part for the OEM intake. ![]() The TB is best to be ported to 62.5mm as its 60mm from the factory. I recommend to do the half shaft cut and an arrow edge on the butterfly plate. ![]() im not expecting to sell the CAI anytime soon, because of the not prettyness and the work involved to make thing run correcty. (tuning) as I was saying in the beginning was that with similar mods on the same dyno I had around 12whp more than any 6mt/7at so beleive me or not, im not being a saleman but a normal guy who does his DIY jobs ![]() My asking price for the CAI is 600$ which doesnt include shipping & paypal fee keep in mind, the CAI as it is shown on the picture costed me 1200$ to be made. I could sell the whole setup of CAI + ported TB for 1600$ (shipping&paypal fee not included) |
![]() |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
MEGAN RACING: SS Downpipes! | G&M Performance | Drivetrain/Engine | 8 | 07-25-2011 12:50 PM |
Megan Drift CBE - my 2 cents | Vince's Red-Z | Intake/Exhaust | 14 | 02-26-2011 07:51 PM |
Megan Racing Exhaust | tyler20c | Intake/Exhaust | 3 | 01-07-2011 12:59 PM |