|
News ! I got some goodies delivered to my door today while I was still working on the HR/VHR engine wiring harness It is NOT an easy job !!! but
|
|||||||
 |
|
|
LinkBack | Thread Tools | Display Modes |
02-11-2013, 08:14 PM
|
#106 (permalink) |
|
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24   |
News !
I got some goodies delivered to my door today while I was still working on the HR/VHR engine wiring harness It is NOT an easy job !!! but im getting there slowly ! Im at about 18 hours of work since I started from the beginning on the wiring harness. I wish I could have found my cheat cheet !  
|
|
|
02-12-2013, 07:29 PM
|
#107 (permalink) |
|
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 |
more good news !!
 After about 3 straight working days on the HR engine harness (28hours). I completed the Version # 1 !!!! I estimate 85% chance of being able to start the engine !! hhehe then I decided to take another picture of my goodies I received a little while ago.  
Last edited by Megan370z; 02-12-2013 at 07:32 PM. |
|
|
|
02-24-2013, 02:10 AM
|
#117 (permalink) | |
|
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 |
Quote:
 the engine was only installed with the PPE header !!! no catback !! on a side note , it was probably very rich by the smell it had !! a lot of tuning has to be done since I installed the VHR injector but the base injector setup is only a copy/paste from the old setup. on the first startup, I decided to just put the OEM intake setup because of the unknown base tune since there was NO AFR sensor installed either. I discovered once everything was installed that my VHR AFR sensor had a different plug than the HR one.... it was only running off from the MAF   
Last edited by Megan370z; 02-24-2013 at 02:25 AM. |
|
|
|
|
03-10-2013, 10:27 PM
|
#118 (permalink) |
|
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 |
small Update !
soo let recap what happen the last time I worked on the car. I had the wiring setup done after 30++ hours then I went ahead to see if the engine would fire up ! which it did but what I didnt mentioned was I completly overlook some very important part of the setup !! Remember the car had an automatic, so this time the car is receiving an 6MT which I had to buy a bunch of stuff !! - Flywheel - clutch - HD CSC - clutch master cylinder - RJM clutch pedal assembly but what was forgotten was the clutch bolts !!!! I had to go thru the dealership to get those . after a week of waiting I decided today to pull the engine out again to do the switch of those bolt since I had some temporaly bolts for the engine fire-up test While I was waiting for those parts (9x bolts + washer and 6 L of 6MT fluid.) I started a new project that will be quite different from anything I have seen on the 370z ! who can guess what it might be ! let just say its under the hood and no . no FI |
|
|
|
03-11-2013, 08:06 AM
|
#120 (permalink) | |
|
A True Z Fanatic
Join Date: Oct 2009
Location: Canada
Posts: 1,156
Drives: 370z
Rep Power: 24 |
Quote:
 if I had a milling machine at work I would probably make a set but we only have a lathe ;( |
|
|
|
|
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| MEGAN RACING: SS Downpipes! | G&M Performance | Drivetrain/Engine | 8 | 07-25-2011 01:50 PM |
| Megan Drift CBE - my 2 cents | Vince's Red-Z | Intake/Exhaust | 14 | 02-26-2011 08:51 PM |
| Megan Racing Exhaust | tyler20c | Intake/Exhaust | 3 | 01-07-2011 01:59 PM |
238Likes
Linear Mode
