Megan Journal

12nismo

So your buddy is running an HR head swap and ITB's and broke 400whp? What else is he running? I've been thinking of going down the ITB rout but havent seen anyone successfully do it on our car. This is VERY interesting...

__________________
nismo Z34 12 0209
JTran Motorsports//Stillen//Fast Intentions//EcuTek//Z1 Motorsports//Eibach//BRIDE //Zspeed//Carbon Signal//Houston Halos//Southbend//Whiteline//TWM//NonStopTuning//Doran Racing

Megan370z

N/A Power
VQ37HR ( Hr engine stroked with VHR crank/rods)
Big Cams !
ITB + Motec ECU.

More power could still be found but he had a cluth assembly break down.

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

Megan370z

He is running;
-ITB
-Motec ECU
-3.5'' Exhaust setup
- his own custom long tube step header (SG header previously now OnpointDyno) he sold several of them on the 350z forum.

There is more power to be found but he had a clutch assembly break down last night.

THere is rumor that the race team using this setup got up to 440whp.
but for this, you must use a drysump . and other secret stuff.

My project for 2013/2014 is that same exact engine setup minus ITB/drysump so im gessing 380whp should be a good guess.

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

zefaulter

Great job on the custom exhaust Those are amazing numbers... Question is, will 380hp be enough for you?

Megan370z

only time will tell..

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

redline06

What an amazing thread, You're the man!!! don't know why I never got around to reading it. Just picked up a spare HR for me to mess with since my HR is up there in mileage, granted its running like a champ but it doesn't hurt to have a long block on hand, esp with only 5k miles on it lol
My plan is to go with the 3.7 crank, stock size HR rods and pistons to pretty much just strengthen the internals possibly for boost. O and of course cams and headwork too to let her breathe.
We've talked on My350 before in regards to bigger TBs, Now since I have one to play with the more I look at the stock intake manifold I highly doubt 2 75mm Maxima TBs will fit lol so I was thinking about using the R35 Intake manifold, what's your take on this?

Also,I could've sworn I read that OnPoints VQ37HR went with OEM HR rods since they're longer than VHR according to this article. Summer Is Ending – Kels, Dyno’s And California : OnPoint Dyno

Megan370z

@ redline06 , I replied to you on the other website.
I just want to avoid having a big discussion about that on this thread

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

carlitos_370z

Subscribed to this great build!!!

Marti

Megan370z, your exhaust work is amazing! That's definitely some quality work there

__________________
Marti - Rev Works, Inc
https://www.facebook.com/Revworks
www.revworksinc.com / marti@revworksinc.com / aim: aimformarti
407-542-7863

Megan370z

Thanks.

I just wish I had some better tooling to make it easier and faster to make.
I'm sure some guys would be interested to pull the trigger on this.

....

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

Megan370z

I'm wondering if anybody would be seriously interested into my custom exhaust.





the kit include the whole exhaust setup which include

- Modified Momentum headers (not the z1 copy)
- Custom Y-Pipe 2.5'' paired to a transition & megaphone to 3.5'' single exit.
- Custom 3.5'' mid pipe with a 18'' resonator.
- Custom Muffler section 3.5'' in & out.
- 2x HFC (y-pipe)
- 2x Resonator (y-pipe)
- Custom rear holding bracket (with bolts)
- All mandrel bent 304SS tubing.
- TIG Welded and Back-Purged for improved stronger welds.
- Equipped with modified V-bands to reduce turbulence.
- No gasket required.
- Much improved scavenging effect due to the both transition and megaphone *Header & Y-Pipe* which mean more power !
- With the benefit of V-Band the swap of those parts can be done in 10 mins !



You will need to remove the rear bracing tower shown in the bottom Red square


then install the provided *blue* rear holding bracket
the 2 holding bolts goes into the already installed welded nut into the frame.
and you will lose the 2 braces going to the front bolts of the sub-frame.
IMO they arent crucial to the rear stability since the 350z does not have it and have the same sub-frame setup.


Ofcourse you will need to remove the rear fog light and slightly cut a circle in it ....



you will have an improved ground clearance since everything was installed to be as close as possible to the frame.

as a bonus half of the exhaust were heat wraped with DEI titanium (100feets of it)


serious offer only please.

Sorry I do not have a VQ37VHR (VVEL) dyno. since I have the HR heads.
IMO this is the best ALL-OUT exhaust setup on the 370z.

If the following parts are installed
- Stillen Gen 3 CAI
- VHR intake manifold (with intake runner smoothed out)
- my custom Throttle body
- Uprev / EcuTek

I predict it will outperform the Z1 setup that had a result of 342whp with one of our 370z member on their dynojet.

edit;
My guess is by over 10whp from what I already gained previously from stock to fully modded
256whp to 324whp = 68whp of gain with my previous less optimized exhaust & HR intake manifold

when Z1 only got a gain from stock to fully modded including their secret mod to 61whp of gain ( from 280 to 341 )

Why am I selling ?
Going another route. and no im not selling the Z

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

Megan370z

the exhaust kit is officially on sale in the sale threads. look it up.

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

Megan370z

Guess what...

Every N/A parts required to gain atleast a minimun of 70+ whp over stock is now for sale.
Remember I gained 68whp with a less effective exhaust that was made to fit into the decibel limit rules.

This custom 3.5'' exhaust is way more effective than my previous one.

It will be best to be sold as a kit since everything must match together to avoid bottle neck flow problems.

this include every parts that can be seen in this exhaust thread ( CLICK ME )

this package deal add the following parts ;

- Custom CAI which include a bigger Maf Tube
- Custom Throttle body
- NST Light weight pulley kit ( crank & alternator )
- Base Uprev ROM for this setup ( THIS IS NOT A LICENSE).
I just need your ECU part number and the tuned ROM will be sent to you with the back to stock ROM. *This alone save your $$ on tuning time...*

this package deal price is set at ; 4750$

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

Megan370z

Hey, New Update !!!

no.... its not about my Awesome Package N/A Power Deal that can give you a minimum of 70 Whp over a stock 370z.......


Its about a new toy that I just got this morning !!!

After 2 burn and 1 on the way to be a paper weight, I finally got to do what I was supposed to buy 2 years ago !
A true LSD

Im still debating on the final parts for the Diff oil cooler but anyway
there it is.

Cusco RS LSD 1.5 / 2 Way

__________________
Megan Journal *Click Me* ....................One Man Team Motorsport *Click Me*

wheee!

Is this both 1.5 and 2 way locking? Same parts, just optional configuration?

__________________