Rusty's Nismo Journal

Rusty · 01-25-2019, 03:57 PM

Quote:

Originally Posted by Mick_12Nismo

This looks like a nice upgrade Rusty. How are you attaching the Allstar Performance aluminum flange to the (OEM?) brake shield? Rivets? I've ordered a set of ducts from Kevin at FE and they are 3" OD. I'm looking to bypass the Stillen kit entirely and essentially do the same thing as you are. Also, how long were the hoses that you ordered? Could you get by with a single 10 ft piece (5' for each side) or is that too short?

Thanks,
Mick

I'm going to rivet the flange to the shield. The shield is steel and the flange is aluminum. The hose I got is 10ft long. I'm hoping that's enough to do both sides. That hose is $$

Rusty · 01-25-2019, 03:59 PM

Quote:

Originally Posted by gbrettin

Body glue works too.

I don't think I would trust the glue to hold the flange to the brake shield because of the heat.

Hotrodz · 01-25-2019, 04:10 PM

My guy cut the 2" flanges off the Stillen bracket and fab on a 3".

Sent from my SM-G965U using Tapatalk

Rusty · 01-25-2019, 04:18 PM

Quote:

Originally Posted by Hotrodz

My guy cut the 2" flanges off the Stillen bracket and fab on a 3".

Sent from my SM-G965U using Tapatalk

Think I might sell my Stillen kit after I finish this project up. Shields, hoses, brackets, etc.

Mick_12Nismo · 01-25-2019, 05:27 PM

Quote:

Originally Posted by Rusty

I'm going to rivet the flange to the shield. The shield is steel and the flange is aluminum. The hose I got is 10ft long. I'm hoping that's enough to do both sides. That hose is $$

Thanks for the feedback Rusty. I noted the same thing about the hose pricing. I found a 10 ft section of Allstar Performance hose (3" diameter, 550 degree limit) for $117 on Jegs.com I also found a 12 ft section of "high temperature silicine air duct hose" (3" diameter, 450 degree continuous, 500 degree max) for $117 on pegasusautoracing.com. I'm not sure that the 50 degree difference is meaningful, especially after the ducts are in place and the added cooling is realized.

I am curious as to whether you find that the single 10' piece of hose is long enough for both sides.

Best,
Mick

gbrettin · 01-25-2019, 07:03 PM

Quote:

Originally Posted by Rusty

I don't think I would trust the glue to hold the flange to the brake shield because of the heat.

Mine has been on for quiet some time just fine. It's an option.

Rusty · 01-30-2019, 08:32 PM

Here's my write up on the Bell Raceworks diff brace from Z1. I trashed it.

Bell Raceworks Diff Brace Install

Rusty · 02-02-2019, 07:34 PM

Was working on the Z today. Ran into a problem with the SLP bushings I was installing. I updated my thread on rear suspension. Starts on post #28.

The Complete SPL Rear Suspension (Almost)

onzedge · 02-02-2019, 08:01 PM

Quote:

Originally Posted by Rusty

Was working on the Z today. Ran into a problem with the SLP bushings I was installing. I updated my thread on rear suspension. Starts on post #28.

The Complete SPL Rear Suspension (Almost)

Rusty · 02-02-2019, 08:02 PM

Quote:

Originally Posted by onzedge

Chit happens.

onzedge · 02-02-2019, 09:38 PM

Quote:

Originally Posted by Rusty

Chit happens.

Rusty · 02-02-2019, 10:14 PM

Getting ready to drop the sub-frame to install the SPL bushing in the sub-frame mounts. So I decided to drain the rear diff of fluid. Very pleased with what came out. No particles that I can see. The lube is dark, but not black. Pulled apart the screen filter that I installed in the line that goes from the diff to the cooler. Nothing in there either.

Man.......that OS Giken lube is thick.

I'm going to leave it drain over night. Oh, there is about 2,000 miles on this lube since I installed the OS Giken diff and cooler. So it was over due for a change.

FL 4Motion · 02-06-2019, 12:42 AM

Quote:

Originally Posted by Rusty

Was working on the Z today. Ran into a problem with the SLP bushings I was installing. I updated my thread on rear suspension. Starts on post #28.

The Complete SPL Rear Suspension (Almost)

SLP? For a second thought you traded for a firehawk.

Rusty · 02-10-2019, 09:40 PM

Pic's of my SPL rear sub-frame bushing install. I'm planning on doing an install thread on it.

Rusty · 02-10-2019, 09:43 PM

And more pic's.

01-25-2019, 04:10 PM	#933 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	My guy cut the 2" flanges off the Stillen bracket and fab on a 3". Sent from my SM-G965U using Tapatalk Rusty and Spooler like this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

01-30-2019, 08:32 PM	#937 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,185 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Here's my write up on the Bell Raceworks diff brace from Z1. I trashed it. Bell Raceworks Diff Brace Install __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-02-2019, 07:34 PM	#938 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,185 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Was working on the Z today. Ran into a problem with the SLP bushings I was installing. I updated my thread on rear suspension. Starts on post #28. The Complete SPL Rear Suspension (Almost) Hotrodz and Spooler like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-02-2019, 10:14 PM	#942 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,185 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Getting ready to drop the sub-frame to install the SPL bushing in the sub-frame mounts. So I decided to drain the rear diff of fluid. Very pleased with what came out. No particles that I can see. The lube is dark, but not black. Pulled apart the screen filter that I installed in the line that goes from the diff to the cooler. Nothing in there either. Man.......that OS Giken lube is thick. I'm going to leave it drain over night. Oh, there is about 2,000 miles on this lube since I installed the OS Giken diff and cooler. So it was over due for a change. onzedge, Hotrodz, Spooler and 2 others like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
O&G's Journal	O&G	Member's 370Z Gallery	648	02-16-2017 04:30 PM
birdmanx1's Nismo Journal ...	birdmanx1	Member's 370Z Gallery	441	10-20-2012 04:47 PM
TROOPER's 370Z NISMO Journal	TROOPER	Member's 370Z Gallery	124	07-29-2011 10:17 AM
[Equinox] Nismo dyno progression journal	Equinox	Engine & Drivetrain	3	02-17-2011 04:11 PM
Z BEST Journal	Z BEST	Member's 370Z Gallery	26	01-09-2011 04:19 PM