Rusty's Nismo Journal

Spooler · 01-09-2019, 09:14 PM

How bad were the SPL subframe solid bushings to install? I am thinking about getting them done at MA while they have everything torn apart. Did you have any noise issues?

Rusty · 01-09-2019, 09:46 PM

Quote:

Originally Posted by Spooler

How bad were the SPL subframe solid bushings to install? I am thinking about getting them done at MA while they have everything torn apart. Did you have any noise issues?

They're still sitting on the bench.

I never got around last winter to install them. I'm going to be tackling these in about 2 weeks. With your neck. I would let MAM install them. I don't think there is anyway to install them without dropping the sub-frame. I'm going to make a cradle to fit my floor jack to make it easier to lower and lift the sub-frame in place. To drop the sub-frame. You have to; remove the tires, calipers, rotors, disconnect the e-brake cable at the e-brake shoes, exhaust pipes, drive shaft, frame bracing. Unplug the speed sensors at the diff. Remove the lower shock bolt. Then undo the 4 nuts that hold the sub-frame in place. Once the sub-frame is down. Use a deep holesaw to cut the center out. Then a sawzall to cut the shell. Just like a diff bushing. Remove the shell. Clean up the hole and use a ball joint press to install the new bushing. That's the way I'm going to do it.

Spartan 1771 · 01-09-2019, 09:55 PM

Quote:

Originally Posted by Rusty

They're still sitting on the bench.

I never got around last winter to install them. I'm going to be tackling these in about 2 weeks. With your neck. I would let MAM install them. I don't think there is anyway to install them without dropping the sub-frame. I'm going to make a cradle to fit my floor jack to make it easier to lower and lift the sub-frame in place. To drop the sub-frame. You have to; remove the tires, calipers, rotors, disconnect the e-brake cable at the e-brake shoes, exhaust pipes, drive shaft, frame bracing. Unplug the speed sensors at the diff. Remove the lower shock bolt. Then undo the 4 nuts that hold the sub-frame in place. Once the sub-frame is down. Use a deep holesaw to cut the center out. Then a sawzall to cut the shell. Just like a diff bushing. Remove the shell. Clean up the hole and use a ball joint press to install the new bushing. That's the way I'm going to do it.

WOW! That's a ton of work!

Rusty · 01-09-2019, 10:04 PM

Quote:

Originally Posted by Spartan 1771

WOW! That's a ton of work!

Figure about a good weekend.

Spooler · 01-09-2019, 10:18 PM

That is exactly why I was going to let them do it. LOL I already have a diff cooler and DSS pro level axles for them to install. Why they are at it. Might as well.

I was under the car to install my diff cooler and tweaked my neck. I said F'it. I will let them do it.

Rusty · 01-12-2019, 08:00 PM

Since I have the front bumper off for the splitter install, and going with the Castrol brake fluid. I decided to up-grade the brake cooling ducts to a 3" hose from the Stillen 2" hose set-up.

Pic's of the 10ft, 3" diameter hose, 4" to 3" reducers. The factory carbon fiber RC brake ducts are designed for a 4" hose.

And the flanges for the brake shield.

Rusty · 01-12-2019, 08:02 PM

Pic of the difference in size between the 2" and 3" hoses.

Rusty · 01-12-2019, 08:03 PM

And this is where I have to change and mod the new reducers to fit the RC brake ducts.

sirnixalot · 01-12-2019, 10:45 PM

you summed up the subframe bushing install perfectly.

it is a gigantic pain in the *** that is worth the effort. The gain in ....predictability? for lack of a better term is worth it. There is some gear whine on deceleration (with whiteline diff bushings) but if you listen to music it's irrelevant.

Rusty · 01-12-2019, 11:06 PM

Quote:

Originally Posted by sirnixalot

you summed up the subframe bushing install perfectly.

it is a gigantic pain in the *** that is worth the effort. The gain in ....predictability? for lack of a better term is worth it. There is some gear whine on deceleration (with whiteline diff bushings) but if you listen to music it's irrelevant.

I can't hear chit now. Between the exhaust and bad hearing.

Rusty · 01-12-2019, 11:20 PM

Removed the old reducers, modded the new reducers to fit. Tomorrow, I'll use 2 part epoxy to hold the pieces together.

onzedge · 01-13-2019, 08:05 AM

Quote:

Originally Posted by Rusty

Removed the old reducers, modded the new reducers to fit. Tomorrow, I'll use 2 part epoxy to hold the pieces together.

Good stuff.

Rusty · 01-14-2019, 09:07 PM

Brake duct work. After the epoxy cures overnight. I'll install them in the bumper tomorrow

Mick_12Nismo · 01-25-2019, 03:35 PM

This looks like a nice upgrade Rusty. How are you attaching the Allstar Performance aluminum flange to the (OEM?) brake shield? Rivets? I've ordered a set of ducts from Kevin at FE and they are 3" OD. I'm looking to bypass the Stillen kit entirely and essentially do the same thing as you are. Also, how long were the hoses that you ordered? Could you get by with a single 10 ft piece (5' for each side) or is that too short?

Thanks,
Mick

gbrettin · 01-25-2019, 03:45 PM

Quote:

Originally Posted by Mick_12Nismo

This looks like a nice upgrade Rusty. How are you attaching the Allstar Performance aluminum flange to the (OEM?) brake shield? Rivets? I've ordered a set of ducts from Kevin at FE and they are 3" OD. I'm looking to bypass the Stillen kit entirely and essentially do the same thing as you are. Also, how long were the hoses that you ordered? Could you get by with a single 10 ft piece (5' for each side) or is that too short?

Thanks,
Mick

Body glue works too.

01-09-2019, 09:14 PM	#916 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	How bad were the SPL subframe solid bushings to install? I am thinking about getting them done at MA while they have everything torn apart. Did you have any noise issues? Rusty likes this.

01-09-2019, 10:18 PM	#920 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	That is exactly why I was going to let them do it. LOL I already have a diff cooler and DSS pro level axles for them to install. Why they are at it. Might as well. I was under the car to install my diff cooler and tweaked my neck. I said F'it. I will let them do it. Spartan 1771 and Rusty like this.

01-12-2019, 10:45 PM	#924 (permalink)
sirnixalot Track Member Join Date: May 2017 Location: Cayman Islands Posts: 685 Drives: 2010 370Z Rep Power: 57454	you summed up the subframe bushing install perfectly. it is a gigantic pain in the *** that is worth the effort. The gain in ....predictability? for lack of a better term is worth it. There is some gear whine on deceleration (with whiteline diff bushings) but if you listen to music it's irrelevant. Rusty likes this. __________________ 2010 Sport - LS3 swap loading 2012 Frontier - BTWTuning VK56DE swap

01-25-2019, 03:35 PM	#929 (permalink)
Mick_12Nismo Base Member Join Date: Jun 2012 Location: Western New York Posts: 104 Drives: 2019 C7 Grand Sport Rep Power: 13	This looks like a nice upgrade Rusty. How are you attaching the Allstar Performance aluminum flange to the (OEM?) brake shield? Rivets? I've ordered a set of ducts from Kevin at FE and they are 3" OD. I'm looking to bypass the Stillen kit entirely and essentially do the same thing as you are. Also, how long were the hoses that you ordered? Could you get by with a single 10 ft piece (5' for each side) or is that too short? Thanks, Mick Rusty likes this. __________________ [SOLD] 2012 Metallic Black NISMO 370z #499

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
O&G's Journal	O&G	Member's 370Z Gallery	648	02-16-2017 04:30 PM
birdmanx1's Nismo Journal ...	birdmanx1	Member's 370Z Gallery	441	10-20-2012 04:47 PM
TROOPER's 370Z NISMO Journal	TROOPER	Member's 370Z Gallery	124	07-29-2011 10:17 AM
[Equinox] Nismo dyno progression journal	Equinox	Engine & Drivetrain	3	02-17-2011 04:11 PM
Z BEST Journal	Z BEST	Member's 370Z Gallery	26	01-09-2011 04:19 PM