O&G's Journal

O&G · 11-19-2011, 05:38 PM

I should have done this a long time ago but I've never been an "active" forum member before. I always used it as a resource. I sold my twin turbo 350 in October of 2010. I have a 2010 Tundra and it wasn't as fun to drive as a turbocharged sports car. That being said, I began my look and it ended in November when I found a 40th Anv. 370z, build number 184 in Dallas. It only had 600 miles on it, I grabbed a friend and we were off before someone else could get it. I would say no less than 2 weeks after I owned the car I already had the Stillen CAI, JWT flywheel, Act clutch, B&M short shifter, test pipes, HKS exhaust and HKS coilovers installed and tuned.....all before HKS jacked their prices up. (I had a lot of money left over from the 350 sale.) I can't stand stock, that's just me.
I'm also very lucky to have many friends and family in the aftermarket auto/motor bike industry. As you all know I'm very close with the people @ JTran Studios and without them my 350 and my 370 would have never existed. When I was building my 350 back in the day I ran into a lot of issues with shady shops and just overall bad luck. Johnny at JTran took my car and fixed everything for free basically. He showed me there are good people in the aftermarket scene. I've been a close friend and loyal supporter of their shop ever since. Johnny is known as the best UpRev tuner in Houston, I honestly don't know why people w/ VQ's, who live in this city or area go anywhere else.
All that crap out of the way I'm going to post a bunch of pictures of the car on it's rise up to where it is now, Some pics are shitty cell phone ones....sry.

PARTS:
• ARIAS Custom 9:1 Pistons (1000 whp capable)
• Aeromotive 340 lph fuel pump, adding a surge tank and another pump, or GTR twin pump setup...TBD
• Auto Power Roll / Harness Bar
• B&M Shifter w/ extended shaft
• CSF Aluminum Radiator/Condenser combo
• CJ Motorsports fuel return kit
• Comp Turbo CT4-7065
• Cosworth Metal Head gasket
• Drop Engineering 09+ Nissan 370Z Transmission Mount
• Engine blueprinted by Ron Burgenholtz
• JTran cooling reservoir w/ oil catch can (all in 1)
• Greddy Info-Meter Touch (boost, oil pressure, OBDII, etc…)
• GTM 1 in, 2 out intercooler
• GTM Engine Mounts
• Upgraded CSC
• Hallman Evolution manual boost controller, upgraded to the new Greddy Profec B (startrek)
• HKS 1 step colder spark plugs
• HKS Hypermax coilovers in conjunction w/ H&R spacers
• HKS 170mm Hi-Power muffler, 3” single exhaust and MBRP Resonator
• Injector Dynamics 850cc, upgrading to 1300's or 2k's for E85
• Innovative wideband A/F Gauge
• JWT Flywheel w/ ACT 6-Puck Clutch (unsprung)
• K1 Rods w/ ARP fastners all around, including L19 studs
• STRI 52mm Fuel Pressure Gauge
• SPC rear camber arms
• TiAL MVR Wastegate, w/ AN 3 braided lines
• TiAL Q BOV x 1 w/ AN 3 braided lines
• Thermo-Tec heat protection, Turbo Blanket, wraps, etc.
• Up-Rev MAFS
• Up-Rev tune by Johnny @ JTran Motorsports
• Z1 Motorsports oil cooler kit

O&G · 11-19-2011, 05:42 PM

This graph goes as follows:

RUN 1 = Baseline w/ intake; 260.154whp and 207.587wtq

RUN 2 = intake, exhaust, UpRev tune; 286.211whp and 218.860wtq

RUN 3 = JTran single turbo 6-7 psi (hit 7psi dwindled to 6psi prior to boost controller install); 385.575whp and 339.400wtq

This dyno will read lower than any I've ever seen, a true "heartbreak" AWD Mustang Dyno. Regardless I've made well over 100+whp and wtq! Pumped up!

O&G · 11-19-2011, 05:46 PM

This graph represents JTran single turbo 6-7 psi vs GTM stg 2 @ 6psi, both cars still needing fine tuning, etc... Twin turbo will always come on faster but watch out, single turbo not far behind.

RUN 1 = GTM; 380.811whp and 315.702wtq

RUN 2 and 3 = JTran; 385.575whp and 339.400wtq

Graph was my Dyno pull @ 6-7psi vs 10 psi Meth run. You can see where the clutch began to slip on the graph

O&G · 11-19-2011, 05:47 PM

Hopefully I'll have better soon!

1st video was an Arby's run, when I throttle hard had to put two hands on the wheel....lol, traction! Didn't really punch it, just more a drivability video! I also did a walk around the car while it was running @ the end of the video.

2nd video was right after we finished fabrication and initial tuning.

Day Run:

This clip is a take off, @ the 8-9 second mark I make small fire out my rear end!

This clip is coming back

This is inside the car, prob reved it up to 6k, nothing too crazy. I have pretty stiff suspension and camera isn't that great but you get an idea.

Skeeterbop · 11-19-2011, 10:44 PM

Looks nice! And to think you did all this in 15 minutes!

O&G · 11-19-2011, 10:47 PM

Quote:

Originally Posted by Skeeterbop

Looks nice! And to think you did all this in 15 minutes!

thanks, 3 of those minutes were used writing this thread!

lochness · 11-19-2011, 11:04 PM

Great looking car. I love the rims.

memorylasts · 11-19-2011, 11:11 PM

Quote:

Originally Posted by O&G

Debating on powder coating the center part of my WORK's the same color as my car Oo....yes no?

No, dont!

haitech · 11-20-2011, 05:09 AM

Quote:

Originally Posted by memorylasts

No, dont!

O&G · 11-20-2011, 12:27 PM

Thanks for the input! Always pays to get others opinions!

O&G · 11-20-2011, 12:31 PM

Anyone know if the GTM S/C intake pipes from the intercooler to the engine are 3 inch diameter? Looking for an easy fix to replace the Stillen CAI I adapted to work for now. MAF voltage is fine because I have the UpRev MAFs but I'd like some more air volume!

VDC_OFF · 12-04-2011, 10:57 PM

nice fabrication work!!

< Subscribed

Ron · 12-04-2011, 11:06 PM

sub'd Love ur car!

O&G · 12-05-2011, 03:46 PM

Thanks homies, boost sensor finely made it in. I'm going to do some fine tuning this week, push it to 10psi and see what she can do. I'll try to make it over to the Dyno Jet @ Chris's Car Doc's but it will probably be on JTrans AWD Mustang Dyno. I'll post some vids and dyno sheets later this week.

stormos · 12-16-2011, 07:45 AM

Nice man,

What is your setup wheels? 20x10 +? 20x11 +?

really nice setup

11-19-2011, 05:38 PM	#1 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	O&G's Journal I should have done this a long time ago but I've never been an "active" forum member before. I always used it as a resource. I sold my twin turbo 350 in October of 2010. I have a 2010 Tundra and it wasn't as fun to drive as a turbocharged sports car. That being said, I began my look and it ended in November when I found a 40th Anv. 370z, build number 184 in Dallas. It only had 600 miles on it, I grabbed a friend and we were off before someone else could get it. I would say no less than 2 weeks after I owned the car I already had the Stillen CAI, JWT flywheel, Act clutch, B&M short shifter, test pipes, HKS exhaust and HKS coilovers installed and tuned.....all before HKS jacked their prices up. (I had a lot of money left over from the 350 sale.) I can't stand stock, that's just me. I'm also very lucky to have many friends and family in the aftermarket auto/motor bike industry. As you all know I'm very close with the people @ JTran Studios and without them my 350 and my 370 would have never existed. When I was building my 350 back in the day I ran into a lot of issues with shady shops and just overall bad luck. Johnny at JTran took my car and fixed everything for free basically. He showed me there are good people in the aftermarket scene. I've been a close friend and loyal supporter of their shop ever since. Johnny is known as the best UpRev tuner in Houston, I honestly don't know why people w/ VQ's, who live in this city or area go anywhere else. All that crap out of the way I'm going to post a bunch of pictures of the car on it's rise up to where it is now, Some pics are shitty cell phone ones....sry. PARTS: • ARIAS Custom 9:1 Pistons (1000 whp capable) • Aeromotive 340 lph fuel pump, adding a surge tank and another pump, or GTR twin pump setup...TBD • Auto Power Roll / Harness Bar • B&M Shifter w/ extended shaft • CSF Aluminum Radiator/Condenser combo • CJ Motorsports fuel return kit • Comp Turbo CT4-7065 • Cosworth Metal Head gasket • Drop Engineering 09+ Nissan 370Z Transmission Mount • Engine blueprinted by Ron Burgenholtz • JTran cooling reservoir w/ oil catch can (all in 1) • Greddy Info-Meter Touch (boost, oil pressure, OBDII, etc…) • GTM 1 in, 2 out intercooler • GTM Engine Mounts • Upgraded CSC • Hallman Evolution manual boost controller, upgraded to the new Greddy Profec B (startrek) • HKS 1 step colder spark plugs • HKS Hypermax coilovers in conjunction w/ H&R spacers • HKS 170mm Hi-Power muffler, 3” single exhaust and MBRP Resonator • Injector Dynamics 850cc, upgrading to 1300's or 2k's for E85 • Innovative wideband A/F Gauge • JWT Flywheel w/ ACT 6-Puck Clutch (unsprung) • K1 Rods w/ ARP fastners all around, including L19 studs • STRI 52mm Fuel Pressure Gauge • SPC rear camber arms • TiAL MVR Wastegate, w/ AN 3 braided lines • TiAL Q BOV x 1 w/ AN 3 braided lines • Thermo-Tec heat protection, Turbo Blanket, wraps, etc. • Up-Rev MAFS • Up-Rev tune by Johnny @ JTran Motorsports • Z1 Motorsports oil cooler kit Megan370z, elperuano, joes40th and 1 others like this. __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal Last edited by O&G; 04-13-2014 at 07:26 PM.

11-19-2011, 05:42 PM	#2 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	DyNo This graph goes as follows: RUN 1 = Baseline w/ intake; 260.154whp and 207.587wtq RUN 2 = intake, exhaust, UpRev tune; 286.211whp and 218.860wtq RUN 3 = JTran single turbo 6-7 psi (hit 7psi dwindled to 6psi prior to boost controller install); 385.575whp and 339.400wtq This dyno will read lower than any I've ever seen, a true "heartbreak" AWD Mustang Dyno. Regardless I've made well over 100+whp and wtq! Pumped up! Shaggy370Z likes this. __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal Last edited by O&G; 12-31-2011 at 02:29 PM.

11-19-2011, 05:46 PM	#3 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	DyNo This graph represents JTran single turbo 6-7 psi vs GTM stg 2 @ 6psi, both cars still needing fine tuning, etc... Twin turbo will always come on faster but watch out, single turbo not far behind. RUN 1 = GTM; 380.811whp and 315.702wtq RUN 2 and 3 = JTran; 385.575whp and 339.400wtq Graph was my Dyno pull @ 6-7psi vs 10 psi Meth run. You can see where the clutch began to slip on the graph __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal Last edited by O&G; 04-26-2012 at 12:57 AM.

11-19-2011, 05:47 PM	#4 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	Shitty cell phone vids Hopefully I'll have better soon! 1st video was an Arby's run, when I throttle hard had to put two hands on the wheel....lol, traction! Didn't really punch it, just more a drivability video! I also did a walk around the car while it was running @ the end of the video. 2nd video was right after we finished fabrication and initial tuning. Day Run: This clip is a take off, @ the 8-9 second mark I make small fire out my rear end! This clip is coming back This is inside the car, prob reved it up to 6k, nothing too crazy. I have pretty stiff suspension and camera isn't that great but you get an idea. GaleForce and joes40th like this. __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal Last edited by O&G; 05-02-2013 at 05:52 PM.

11-19-2011, 10:44 PM	#5 (permalink)
Skeeterbop A True Z Fanatic Join Date: Jan 2011 Location: Fort Bliss, TX Age: 40 Posts: 1,440 Drives: 2011 GM 370 base SP Rep Power: 16	Looks nice! And to think you did all this in 15 minutes! __________________ Srenity: "Yeah no rest needed to spread the love when your 20 that's for sure...."

11-19-2011, 11:04 PM	#7 (permalink)
lochness Base Member Join Date: Mar 2011 Location: Columbus, OH Posts: 110 Drives: 12 WRX STI Sedan Rep Power: 14	Great looking car. I love the rims. __________________ Platinum Graphite 2010 370Z w/ Sport Package SOLD Still for Sale HERE - See if you can count the errors in the post New DD and Fun Car - 2012 DGM STI Sedan

11-20-2011, 12:27 PM	#10 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	Thanks for the input! Always pays to get others opinions! __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal

11-20-2011, 12:31 PM	#11 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	Anyone know if the GTM S/C intake pipes from the intercooler to the engine are 3 inch diameter? Looking for an easy fix to replace the Stillen CAI I adapted to work for now. MAF voltage is fine because I have the UpRev MAFs but I'd like some more air volume! __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal

12-04-2011, 10:57 PM	#12 (permalink)
VDC_OFF A True Z Fanatic Join Date: Aug 2011 Location: Houston (Pearland) Age: 44 Posts: 1,205 Drives: 2011 370Z M6 Rep Power: 17	nice fabrication work!! < Subscribed

12-04-2011, 11:06 PM	#13 (permalink)
Ron A True Z Fanatic Join Date: Oct 2010 Location: Houston, TX Posts: 3,009 Drives: TT '11 PW Nismo #113 Rep Power: 22	sub'd Love ur car! __________________ 2011 Twin Turbo PW nismo #113 - My Journal - My TT Build Thread [ GTM GTX Stg2 TT \|\| HKS EVC6 \|\| Custom CarPC \|\| F.I 3'' TDX CBE \|\| SB 6puck clutch/ZSpeed CSC \|\| BC BR Coilovers \|\| SPC camber arms \|\| Work VSS-X \|\| Custom Headlights \|\| PW:JDM CF Covers \|\| Seibon CF Engine Cover ]

12-05-2011, 03:46 PM	#14 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	Thanks homies, boost sensor finely made it in. I'm going to do some fine tuning this week, push it to 10psi and see what she can do. I'll try to make it over to the Dyno Jet @ Chris's Car Doc's but it will probably be on JTrans AWD Mustang Dyno. I'll post some vids and dyno sheets later this week. __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal

12-16-2011, 07:45 AM	#15 (permalink)
stormos Base Member Join Date: Sep 2009 Location: Czech republic Posts: 72 Drives: 2010-37OZ-Blue-6M Rep Power: 16	Nice man, What is your setup wheels? 20x10 +? 20x11 +? really nice setup

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
tag journal with car color	bflosabre91	The370Z.com Feedback, Suggestions & Questions	1	05-12-2011 01:46 PM
Tsolin01's Journal	tsolin01	Member's 370Z Gallery	25	04-24-2011 09:12 PM
Z BEST Journal	Z BEST	Member's 370Z Gallery	26	01-09-2011 04:19 PM
tao168's Journal	tao168	Member's 370Z Gallery	12	06-14-2010 09:19 AM