My 2010 Sport

sirnixalot · 09-30-2017, 09:26 AM

Finally decided to make a thread after a few months

The day I picked it up from the docks.

Unfortunately not long after the fuel pump died so...

Deatschwerks DW200, a pump install kit and fuel pressure gauge kit from CJM went in

A few weeks pass and it starts having intermittent starting issues and the fuel level gauge ends up at different levels while driving. I toned the harness out and the stock wiring was fine but there was a short in the factory fuel top hat. So CJM to the rescue again with their billet top hat and milspec bulkhead connector.

With the reliability stuff out of the way I moved onto the stereo. The headunit I chose was the Sony MEX-XB100BT, a friend was clearing out some stuff and gave me an older Rockford 25 to life 5 channel amp to power the CT Sounds Meso 6.5" components and a Rockford Prime 10" sub in a slot ported enclosure.

Magnet comparison

I cut the stock speaker out of the frame and used that to mount the new speakers.

I am still waiting on these to come back from the body shop. I don't have the patience for sanding body filler to shape.

Amp mounted on some stainless stilts, the sub and enclosure are below the new trunk floor. I made everything from 5/8" MDF. Waiting for a speaker grill to come in to finish it off.

It definitely won't rattle anyone's windows but it's clean even when played loud.

sirnixalot · 09-30-2017, 09:51 AM

Next up....Suspension!

Ordered up the following from THMotorsports
Fortune Auto 500 series coilovers with 12k/10k springs
Voodoo 13 rear traction rods
Voodoo 13 rear subframe solid bushings
Whiteline diff bushings
SPL eccentric lock out kit

And Z1 Motorsports
Street front upper control arms (no race arms in stock at the time)
Race rear camber arm

Onto the pics

Control arms

Diff bushings

Worst 3 hours of my life

All bushings changed, subframe and diff repainted with VHT chassis epoxy paint. I painted all the rest of the under braces too.

Z1 & Voodoo rear arms installed

Sexy new coilovers from Fortune

Rear springs in. Was setting ride height without the shock in first

Fortune front coils & Z1 upper arms

As it sits as of Thursday. I need to raise the rear up about a half inch. When i set the rear right height I didn't take into account putting preload on the springs.

Since the Z1 arms are a chore to adjust, I am trying to get them as close to -2* as possible to cut down on labor when it gets aligned. I have the passenger at 2* according to my Iphone being pressed against the brake rotor, the drivers side still needs work as that's at -3.7*.

I did a few cosmetic things while I was waiting on a few parts to arrive.

Rear duck bill (My friends LS1 FD in the back ground)

Mocking up the front lip. Thinking to black out the bumper mouth and paint the outer parts of the lip white like what people do with the 3 piece Evo-R lip. Also you can kinda make out the blacked out the headlight housings and paint matched shrouds.

That's pretty up to date. I'll be finishing the adjustments today after work and taking the car to get aligned on monday.

Hotrodz · 09-30-2017, 11:21 AM

Very nice!

Sent from my SM-N910P using Tapatalk

Z-Girl 12 · 09-30-2017, 11:34 AM

Me likey...and the RX in the background!

axmea? · 09-30-2017, 02:29 PM

I loved that lip. Goes well with the skirts and spats that came with it. I recommend 3M VHB (white/silver). You will need to explore where there are gaps and double up on the VHB (2 layers or even more in some parts) because the back side is uneven. I also recommend skid plates for the edges (those in front of the tires) for longer life. Use an aluminum sheet if you can find one. Steel sheets will rust unless you don't mind. All this from past experience/learnings.

God-Speed · 09-30-2017, 06:55 PM

Keep it going, your on your way!!

sirnixalot · 10-02-2017, 08:46 AM

Thanks everyone.

Setting the front ride height was kicking my *** saturday night. I had some 2x6 under the front tires so i was able to get the jack under the car. Got the measurements between the wheel center and the fender perfect, rolled car off the 2x6 and it's 1/2" higher in the front than it should be.

I'll finish up thursday and drop it for alignment then.

Got a great deal on a single rear wheel from MacCool, once I get my hands on another it will be tire's and sway's time.

Patrick@AAMComp · 10-03-2017, 04:34 PM

Looking good

matrix_square · 10-03-2017, 08:22 PM

Nice ! What front lip is that ?

sirnixalot · 11-07-2017, 07:14 PM

Quote:

Originally Posted by matrix_square

Nice ! What front lip is that ?

Ebay

Had the car in the body shop to fix some rust spots and to paint/install the front lip while I was in Vegas at Sema.

Hatch hinge rust

Repaired and primed

axmea? · 11-07-2017, 11:00 PM

Nice. Very similar to when I started with my first kit. Not sure what you plan on doing for next but I recommend getting the side skirts that go with it instead of the side blades many people go with. And push out the wheels with spacers. Congrats.

sirnixalot · 11-08-2017, 09:57 AM

Quote:

Originally Posted by axmea?

Nice. Very similar to when I started with my first kit. Not sure what you plan on doing for next but I recommend getting the side skirts that go with it instead of the side blades many people go with. And push out the wheels with spacers. Congrats.

I am pretty happy with it aesthetics wise for the time being. I have 20mm spacers all around at the moment.

Once I find another deal on a sport rear wheel I'll be able to go 19x10 all around with 285's.

Next round of mods is going to be a Cusco RS 1.5 way diff, the above wheel/tire setup and some Hotchkis or Whiteline sway bars.

Hotrodz · 11-08-2017, 10:30 AM

Quote:

Originally Posted by sirnixalot

I am pretty happy with it aesthetics wise for the time being. I have 20mm spacers all around at the moment.

Once I find another deal on a sport rear wheel I'll be able to go 19x10 all around with 285's.

Next round of mods is going to be a Cusco RS 1.5 way diff, the above wheel/tire setup and some Hotchkis or Whiteline sway bars.

Go with the Hotchkis! Lot of documented issues with Whiteline.

Sent from my SM-N910P using Tapatalk

sirnixalot · 11-08-2017, 05:17 PM

Quote:

Originally Posted by Hotrodz

Go with the Hotchkis! Lot of documented issues with Whiteline.

Sent from my SM-N910P using Tapatalk

Really? I've used them in the past with success. I'll take a trip down the google rabbit hole and see what I find

axmea? · 11-08-2017, 07:53 PM

I agree with hotrodz. One I recall was more like a factory defect that should have been caught before landing on the consumer. Whiteline took care of it though and covered it.

09-30-2017, 09:26 AM	#1 (permalink)
sirnixalot Track Member Join Date: May 2017 Location: Cayman Islands Posts: 685 Drives: 2010 370Z Rep Power: 57454	My 2010 Sport Finally decided to make a thread after a few months The day I picked it up from the docks. Unfortunately not long after the fuel pump died so... Deatschwerks DW200, a pump install kit and fuel pressure gauge kit from CJM went in A few weeks pass and it starts having intermittent starting issues and the fuel level gauge ends up at different levels while driving. I toned the harness out and the stock wiring was fine but there was a short in the factory fuel top hat. So CJM to the rescue again with their billet top hat and milspec bulkhead connector. With the reliability stuff out of the way I moved onto the stereo. The headunit I chose was the Sony MEX-XB100BT, a friend was clearing out some stuff and gave me an older Rockford 25 to life 5 channel amp to power the CT Sounds Meso 6.5" components and a Rockford Prime 10" sub in a slot ported enclosure. Magnet comparison I cut the stock speaker out of the frame and used that to mount the new speakers. I am still waiting on these to come back from the body shop. I don't have the patience for sanding body filler to shape. Amp mounted on some stainless stilts, the sub and enclosure are below the new trunk floor. I made everything from 5/8" MDF. Waiting for a speaker grill to come in to finish it off. It definitely won't rattle anyone's windows but it's clean even when played loud. husam2012 likes this. __________________ 2010 Sport - LS3 swap loading 2012 Frontier - BTWTuning VK56DE swap Last edited by sirnixalot; 10-02-2017 at 08:41 AM.

09-30-2017, 09:51 AM	#2 (permalink)
sirnixalot Track Member Join Date: May 2017 Location: Cayman Islands Posts: 685 Drives: 2010 370Z Rep Power: 57454	Next up....Suspension! Ordered up the following from THMotorsports Fortune Auto 500 series coilovers with 12k/10k springs Voodoo 13 rear traction rods Voodoo 13 rear subframe solid bushings Whiteline diff bushings SPL eccentric lock out kit And Z1 Motorsports Street front upper control arms (no race arms in stock at the time) Race rear camber arm Onto the pics Control arms Diff bushings Worst 3 hours of my life All bushings changed, subframe and diff repainted with VHT chassis epoxy paint. I painted all the rest of the under braces too. Z1 & Voodoo rear arms installed Sexy new coilovers from Fortune Rear springs in. Was setting ride height without the shock in first Fortune front coils & Z1 upper arms As it sits as of Thursday. I need to raise the rear up about a half inch. When i set the rear right height I didn't take into account putting preload on the springs. Since the Z1 arms are a chore to adjust, I am trying to get them as close to -2* as possible to cut down on labor when it gets aligned. I have the passenger at 2* according to my Iphone being pressed against the brake rotor, the drivers side still needs work as that's at -3.7*. I did a few cosmetic things while I was waiting on a few parts to arrive. Rear duck bill (My friends LS1 FD in the back ground) Mocking up the front lip. Thinking to black out the bumper mouth and paint the outer parts of the lip white like what people do with the 3 piece Evo-R lip. Also you can kinda make out the blacked out the headlight housings and paint matched shrouds. That's pretty up to date. I'll be finishing the adjustments today after work and taking the car to get aligned on monday. gbrettin, axmea?, Hotrodz and 3 others like this. __________________ 2010 Sport - LS3 swap loading 2012 Frontier - BTWTuning VK56DE swap

09-30-2017, 11:21 AM	#3 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	Very nice! Sent from my SM-N910P using Tapatalk __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

09-30-2017, 11:34 AM	#4 (permalink)
Z-Girl 12 A True Z Fanatic Join Date: Apr 2012 Location: Florida Posts: 4,105 Drives: Spirited Rep Power: 11716	Me likey...and the RX in the background! __________________ 2012 Z-SOLD 2014 Nismo #565 Fast Intentions CBE/HFC/Swift/SPC/RJM/H&R-15/20mm/Z1 CAI/Headers/Intake Manifold w/Uprev Tune 328.31whp/263.64tq

09-30-2017, 02:29 PM	#5 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,235 Drives: WELL ZED PW 6MT Rep Power: 53241	I loved that lip. Goes well with the skirts and spats that came with it. I recommend 3M VHB (white/silver). You will need to explore where there are gaps and double up on the VHB (2 layers or even more in some parts) because the back side is uneven. I also recommend skid plates for the edges (those in front of the tires) for longer life. Use an aluminum sheet if you can find one. Steel sheets will rust unless you don't mind. All this from past experience/learnings. Hotrodz and sirnixalot like this. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

09-30-2017, 06:55 PM	#6 (permalink)
God-Speed A True Z Fanatic Join Date: Sep 2010 Location: Austin, Tx. Posts: 4,363 Drives: Prototype Rep Power: 2684377	Keep it going, your on your way!!

10-02-2017, 08:46 AM	#7 (permalink)
sirnixalot Track Member Join Date: May 2017 Location: Cayman Islands Posts: 685 Drives: 2010 370Z Rep Power: 57454	Thanks everyone. Setting the front ride height was kicking my *** saturday night. I had some 2x6 under the front tires so i was able to get the jack under the car. Got the measurements between the wheel center and the fender perfect, rolled car off the 2x6 and it's 1/2" higher in the front than it should be. I'll finish up thursday and drop it for alignment then. Got a great deal on a single rear wheel from MacCool, once I get my hands on another it will be tire's and sway's time. __________________ 2010 Sport - LS3 swap loading 2012 Frontier - BTWTuning VK56DE swap

10-03-2017, 04:34 PM	#8 (permalink)
Patrick@AAMComp Base Member Join Date: Sep 2014 Location: Maryland Posts: 160 Drives: with steering wheel Rep Power: 20	Looking good Quicksilvers likes this. __________________ Luis R. aamcompetition.com

10-03-2017, 08:22 PM	#9 (permalink)
matrix_square Enthusiast Member Join Date: Dec 2009 Location: Atlanta Posts: 452 Drives: Evo9-S2K-RSX-S-Z370? Rep Power: 15	Nice ! What front lip is that ? __________________ 2004 Honda S2000 GPW 2005 Honda S2000 Suzuka Blue 2005 Acura RSX Type-S PWP 2006 Mitsubishi Lancer EVO 9 MR Graphite Gray Nissan 370Z Monterrey Blue Sport/Touring/Nav package

11-07-2017, 11:00 PM	#11 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,235 Drives: WELL ZED PW 6MT Rep Power: 53241	Nice. Very similar to when I started with my first kit. Not sure what you plan on doing for next but I recommend getting the side skirts that go with it instead of the side blades many people go with. And push out the wheels with spacers. Congrats. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

11-08-2017, 07:53 PM	#15 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,235 Drives: WELL ZED PW 6MT Rep Power: 53241	I agree with hotrodz. One I recall was more like a factory defect that should have been caught before landing on the consumer. Whiteline took care of it though and covered it. Hotrodz likes this. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
370Z For Sale 2010 Black 7AT with Sport	ViCiouS	370Z For Sale	6	07-25-2016 07:55 PM
2010 370 Z Sport Package	sweetazzz16	Cars for sale (Private Classifieds)	1	05-02-2016 06:06 PM
370Z For Sale 2010 Roadster Red W/ Sport Pkg. and Nav	hansoac	370Z For Sale	4	10-17-2011 04:01 PM
FS - my 2010 base + sport PW 6sp	butdamnbrian	Northern California Region	6	10-13-2011 03:37 PM
SA TX 2010 BS 6mt w/sport package	lllll210lllll	370Z For Sale	1	11-03-2010 12:38 AM