Nissan 370Z Forum
Page 450 of 667 « First 350400440448449 450 451452460500550 Last »
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   The Lounge (Off Topic) (http://www.the370z.com/lounge-off-topic/)
-   -   The New "What did you do with your Z today" (with off topic replies) XII (http://www.the370z.com/lounge-off-topic/88173-new-what-did-you-do-your-z-today-off-topic-replies-xii.html)

happytheman 05-05-2014 08:09 PM
Ok...I already know what Onzy thinks (since he has SPC in his siggy)..but SPC...good stuff, or spend the extra on SPL if rear camber correction is required post Swift install?

happytheman 05-05-2014 08:11 PM
Next question: are you all ok with reusing clay if it's not too badly soiled? I used a bit of Griots Paint Cleaning Clay on my hood yesterday..and it wasn't too bad, so I wrapped it in Saran Wrap and figured I'd ask the group for their thoughts.

onzedge 05-05-2014 08:13 PM
Quote:
Originally Posted by happytheman (Post 2807585)
Ok...I already know what Onzy thinks (since he has SPC in his siggy)..but SPC...good stuff, or spend the extra on SPL if rear camber correction is required post Swift install?
I am actually swapping my SPC out for SPL.

madwi 05-05-2014 08:14 PM
Quote:
Originally Posted by happytheman (Post 2807587)
Next question: are you all ok with reusing clay if it's not too badly soiled? I used a bit of Griots Paint Cleaning Clay on my hood yesterday..and it wasn't too bad, so I wrapped it in Saran Wrap and figured I'd ask,the group for their thoughts.
I usually just refold the clay into it self to expose clean areas. Did you rip a chunk off the bar and just use that?

happytheman 05-05-2014 08:18 PM
Quote:
Originally Posted by madwi (Post 2807589)
I usually just refold the clay into it self to expose clean areas. Did you rip a chunk off the bar and just use that?
Just ripped off a chunk about the size of a large gumball. :tup:

happytheman 05-05-2014 08:19 PM
Quote:
Originally Posted by onzedge (Post 2807588)
I am actually swapping my SPC out for SPL.
Oh RLY? Now why would you be doing that, my friend?

Next question: toe bolts...I'm assuming you has them?

onzedge 05-05-2014 08:23 PM
Quote:
Originally Posted by happytheman (Post 2807595)
Oh RLY? Now why would you be doing that, my friend?

Next question: toe bolts...I'm assuming you has them?
I am in spec on the toe, so I did not have to use them.

I picked up a set of SPL cheap so I am swapping them out as soon as I am home on a Friday, which may be never at this rate.

The SPC are fine, but they have been known to break under hard use. It is rare. I would be keeping them if I had not got that smoking deal on the SPL's.

onzedge 05-05-2014 08:23 PM
Who owes me a Rep?

Be honest, now. Search your feelings.

:icon17:

madwi 05-05-2014 08:30 PM
Quote:
Originally Posted by happytheman (Post 2807594)
Just ripped off a chunk about the size of a large gumball. :tup:
Toss it if its showing black areas. A piece that small is no big loss and not worth it potentially wrecking all your hard work.

jlo370z 05-05-2014 08:35 PM
Quote:
Originally Posted by onzedge (Post 2807601)
Who owes me a Rep?

Be honest, now. Search your feelings.

:icon17:
just checked cant send yet. should be soon though:tup:

happytheman 05-05-2014 08:43 PM
Repppp dropped! Carlitos and Nis...I owe you guys. :)

onzedge 05-05-2014 08:45 PM
Quote:
Originally Posted by happytheman (Post 2807630)
Repppp dropped! Carlitos and Nis...I owe you guys. :)
:tiphat:

kenchan 05-05-2014 08:50 PM
Quote:
Originally Posted by happytheman (Post 2807585)
Ok...I already know what Onzy thinks (since he has SPC in his siggy)..but SPC...good stuff, or spend the extra on SPL if rear camber correction is required post Swift install?
not sure. b15's rear camber was -2.9 max at 0.6 toe in or something, which isn't that terrible. i'd do the spring install and see where it takes you. you're going to end up doing a few alignments anyway to dial-in your setup. :D

Quote:
Originally Posted by happytheman (Post 2807587)
Next question: are you all ok with reusing clay if it's not too badly soiled? I used a bit of Griots Paint Cleaning Clay on my hood yesterday..and it wasn't too bad, so I wrapped it in Saran Wrap and figured I'd ask the group for their thoughts.
yep, i re-use my clay if it's not dirty. i usually just roll it up into a ball, place it in my clay jar, and spray into the jar before i close the lid.

onzedge 05-05-2014 08:53 PM
Quote:
Originally Posted by kenchan (Post 2807640)
not sure. b15's rear camber was -2.9 max at 0.6 toe in or something, which isn't that terrible. i'd do the spring install and see where it takes you. you're going to end up doing a few alignments anyway to dial-in your setup. :D



yep, i re-use my clay if it's not dirty. i usually just roll it up into a ball, place it in my clay jar, and spray into the jar before i close the lid.
:iagree:

happytheman 05-05-2014 09:10 PM
Quote:
Originally Posted by kenchan (Post 2807640)
not sure. b15's rear camber was -2.9 max at 0.6 toe in or something, which isn't that terrible. i'd do the spring install and see where it takes you. you're going to end up doing a few alignments anyway to dial-in your setup. :D



yep, i re-use my clay if it's not dirty. i usually just roll it up into a ball, place it in my clay jar, and spray into the jar before i close the lid.
Thanks for the sound advice, as always. You may not cotton to all that lowering nonsense, but you do have a depth of knowledge about it. :tup:


All times are GMT -5. The time now is 04:13 AM.
Page 450 of 667 « First 350400440448449 450 451452460500550 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2