The New “What did you do with your Z today” (with off topic replies) XXXVI

JARblue · 05-12-2020, 07:23 AM

JLarson · 05-12-2020, 07:24 AM

Morning people! Time for some covefe to get my brain going. Glad to say my CEO has given me very positive feedback on my handling of the new role so far, and that's a big relief.

Russ, hope your day is a bit better than the last few have been.

Zingston · 05-12-2020, 07:38 AM

Morning all... chilly start today (59*) with a high of 78*. I'll take it!!!

JARblue · 05-12-2020, 08:14 AM

Quote:

Originally Posted by jchammond

Remember, the housing is not perfectly squared up- as the way it’s welded around it.
I used a large socket on one end, a through bolt as big as would fit & pulled them in place.
Be sure to do as Rusty says & clean hole good with flapper wheel or something, as they have a glue/epoxy residue on them

Yeah. Even the SPL install instructions say to expect some aluminum to shave off due to the oval hole. Got a dremel at the ready.

Quote:

Originally Posted by jchammond

Use a fine thread hardened threaded rod, as big as the hole in bushing

They can still be very snug going in the hole

Think something like this would do?

( Click to show/hide )

BettyZ · 05-12-2020, 08:17 AM

Hola 'itches! Remember to wear masks and put EW on the iggy list today!

sx moneypit · 05-12-2020, 08:18 AM

Mornin' folks!

Spooler · 05-12-2020, 08:21 AM

Quote:

Originally Posted by JARblue

Do you have a recommendation for a kit that can press/pull bushings in/out of the rear suspension member? I wasn't happy with the quote I got for the installation of my SPL bushings.

It was expensive because it is a sucky job that takes a while. The one job you would be better off paying someone else to do you nut up. Go figure. Kinda backwards.

JARblue · 05-12-2020, 08:35 AM

Quote:

Originally Posted by Spooler

It was expensive because it is a sucky job that takes a while. The one job you would be better off paying someone else to do you nut up. Go figure. Kinda backwards.

Idk... I just bought an 1100 ft lb impact wrench. Might as well put it to use. And $150 for a press/pull kit seems like a reasonable investment since I'm saving some labor costs. Maybe I'll just see if I can get a couple more quotes for the work.

Leingod · 05-12-2020, 08:43 AM

Rusty, really hope your streak turns around soon. Sorry it's been such a crappy week for you. I'll have a drink for you tonight.

eastwest2300 · 05-12-2020, 08:45 AM

Quote:

Originally Posted by Hotrodz

Joby's azz backwards garage build FTW!

Rusty · 05-12-2020, 08:50 AM

Quote:

Originally Posted by JARblue

Do you have a recommendation for a kit that can press/pull bushings in/out of the rear suspension member? I wasn't happy with the quote I got for the installation of my SPL bushings.

The rear suspension inner bushings have to be cut out with a hole saw. Then use a hacksaw to cut the outer shell in 2 places. Then tap the outer shell out. I used a ball joint press to press the new SPL bearings into place. Everything is in my threads.

eastwest2300 · 05-12-2020, 08:53 AM

Quote:

Originally Posted by BettyZ

Hola 'itches! Remember to wear masks and put EW on the iggy list today!

please do, especially you.. add me!!! right now!!!

BettyZ · 05-12-2020, 09:08 AM

Did anyone hear something?

Rusty · 05-12-2020, 09:08 AM

I'z up.

Nice bright sunny day. 44F now, going up to 54F. Tonight is the last cold night. Then it's in the 70's.

Just got off the phone with the repair shop. Basically what happened.
Bearings going bad in the fan hub. Allowing the fan to move around. Chewed through belt.

Replaced belt. Didn't know that the bearings are going bad.

Bearings failed later. Letting the fan to chew into intercooler. Fan blades broke and took out the bottom radiator tank. And ripping the wiring out from the ecu controller. The damage to the intercooler and radiator is bad enough to warrant replacement, not repair.

The renters muddy everything up as they still wanted to go to the beach. They wants the shop to overnight the parts, and that would have cost another $650. Wife put a stop to that. So the renters are out of the picture now.

Ghostvette · 05-12-2020, 09:11 AM

Quote:

Originally Posted by Rusty

To top things off. The CEL came on in the Grand Cherokee the other day.

Took the Jeep to the dealership today. They pulled a code out. It was for a leak on the Evap system. Can't find it. Cleared the code and it hasn't come back.

Gas cap? My Honda dropped an evap code and it turned out to be a small leak at the top of the gas tank where the pump goes. Pain in my azz.....

05-12-2020, 07:23 AM	#6121 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	jchammond likes this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

05-12-2020, 07:24 AM	#6122 (permalink)
JLarson A True Z Fanatic Join Date: Jun 2017 Location: Media, PA Posts: 4,074 Drives: 14 Nissan 370z MR M6 Rep Power: 2684370	Morning people! Time for some covefe to get my brain going. Glad to say my CEO has given me very positive feedback on my handling of the new role so far, and that's a big relief. Russ, hope your day is a bit better than the last few have been. FL 4Motion, JARblue, Rusty and 9 others like this. __________________ 2014 370z Touring Sport Magma Red MT // BP Single Turbo 6467 // 63mm TB's // Z1 Ported Upper Mani // RJM Pedal // Zspeed Stage 3 Clutch // 526 WHP, 451 WTQ 2006 350z (Sold) // 1990 300zx (Sold) // 1985 300zx 2+2 (Sold)

05-12-2020, 07:38 AM	#6123 (permalink)
Zingston A True Z Fanatic Join Date: May 2017 Location: Florida Posts: 4,028 Drives: like it's a rental. Rep Power: 2684370	Morning all... chilly start today (59) with a high of 78. I'll take it!!! God-Speed, Rusty, Zoren 370 and 7 others like this.

05-12-2020, 08:17 AM	#6125 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Hola 'itches! Remember to wear masks and put EW on the iggy list today! JARblue, Rusty, Zoren 370 and 6 others like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

05-12-2020, 08:18 AM	#6126 (permalink)
sx moneypit Premium Member Join Date: Oct 2014 Location: Memphis,Tn. Age: 67 Posts: 3,331 Drives: 2010 370Z PG 6 spd Rep Power: 2684371	Mornin' folks! God-Speed, JARblue, Rusty and 5 others like this.

05-12-2020, 08:43 AM	#6129 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,060 Drives: In Circles Rep Power: 2684396	Rusty, really hope your streak turns around soon. Sorry it's been such a crappy week for you. I'll have a drink for you tonight. JARblue, Rusty, Hotrodz and 4 others like this. __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

05-12-2020, 09:08 AM	#6133 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 37 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Did anyone hear something? redondoaveb likes this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

05-12-2020, 09:08 AM	#6134 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,173 Drives: 2011 Nismo GM 6M Rep Power: 2684437	I'z up. Nice bright sunny day. 44F now, going up to 54F. Tonight is the last cold night. Then it's in the 70's. Just got off the phone with the repair shop. Basically what happened. Bearings going bad in the fan hub. Allowing the fan to move around. Chewed through belt. Replaced belt. Didn't know that the bearings are going bad. Bearings failed later. Letting the fan to chew into intercooler. Fan blades broke and took out the bottom radiator tank. And ripping the wiring out from the ecu controller. The damage to the intercooler and radiator is bad enough to warrant replacement, not repair. The renters muddy everything up as they still wanted to go to the beach. They wants the shop to overnight the parts, and that would have cost another $650. Wife put a stop to that. So the renters are out of the picture now. eastwest2300, God-Speed, Hotrodz and 7 others like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) Cooking Edition	Leingod	The Lounge (Off Topic)	319	09-28-2021 11:10 PM
The New “What did you do with your Z today” (with off topic replies) XXXV	Spoiler	The Lounge (Off Topic)	9999	04-08-2020 09:47 PM
The New “What did you do with your Z today” (with off topic replies) XXXIV	Spoiler	The Lounge (Off Topic)	9999	01-24-2020 06:42 PM
The New "What did you do with your Z today" (with off topic replies) XXII	eastwest2300	The Lounge (Off Topic)	10001	04-05-2016 09:15 PM