The New “What did you do with your Z today” (with off topic replies) XXXIV

jchammond

I’ll then have minimum 24” clearance underneath for leveled/pack groundwork

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

-ZS-Carpenter

We are about to ride the Illinois weather roller coaster Somewhere between 1 and 6 inches of snow later today/over night followed by maybe some ice Then rain and a high of 40 early tomorrow morning. Then the bottom falls out and drops to 4 with 25mph~ winds Don't think the wind chill will be above 0 until Wednesday then more rain and mid 40s by the end of next week.

JLarson

Happy Friday everybody! May you all enjoy a half day of work and a whole day of buying Z parts.

__________________
2014 370z Touring Sport Magma Red MT // BP Single Turbo 6467 // 63mm TB's // Z1 Ported Upper Mani // RJM Pedal // Zspeed Stage 3 Clutch // 526 WHP, 451 WTQ
2006 350z (Sold) // 1990 300zx (Sold) // 1985 300zx 2+2 (Sold)

Rusty

I'z up.

Work 9 to 1. Then off for the weekend.

Going to spend the weekend getting my taxes together.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

madwi

They said ~7 inches of snow here starting tonight with winds up to 50mph.
It is currently 14F but its a gorgeous sunrise.

Rusty

We're going to be on the edge of that system. Starting tonight.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

Spooler

Bobby is crooked. Anybody who jumps in bed with him is in the same category in my book.

jchammond

I’ll have to read an catched up later; getting ready for work-but all 50 bolts,nuts,washers installed & barely snugged until block removal tomorrow morning
Went a tick large on the hole to give me movement while I remove blocks from underneath & later will install a crush sleeve in each hole

Attached Images

	50C16C5C-1F46-419F-BCF3-038AB5BEAF83.jpg (288.3 KB, 9 views)
	B94E3B38-380F-4772-A7F0-D6B9C4C7EF0A.jpg (274.0 KB, 9 views)
	68802BE2-8189-443C-BD0D-D306C2A9359A.jpg (271.6 KB, 10 views)
	158F1D74-B8BC-4552-81B7-430339993791.jpg (297.2 KB, 11 views)

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

503.Zed

So much for that “snowstorm” everyone was freaking out about. Roads were fine and not even a delay getting to work. Hope you all have a Good Friday!




Sent from my iPhone using Tapatalk

madwi

Just watched all of Dracula, Netflix's original. wasnt too bad overall.

BettyZ

Coolerworx bros.. did you have to trim the plastic bar on the center console?


Sent from my SM-G955U using Tapatalk

__________________
'14 MB Nismo | Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs.
Betty Mods

JARblue

I wouldn't worry about it. Since you're gonna sell it to me anyway

__________________

madwi

I didnt have to.

BettyZ

Did you pull the center console when you did the install or leave it in place?

Sent from my SM-G955U using Tapatalk

__________________
'14 MB Nismo | Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs.
Betty Mods

redondoaveb

Center console doesn't need to be removed

__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo
750whp/700ft.lbs