The New "What did you do with your Z today" (with off topic replies) XXXIII

BoneZ · 07-31-2019, 01:04 PM

Quote:

Originally Posted by eastwest2300

apple has a lot of haters duuude.

Reps Apple...RepZ no longer maxed out

Ghostvette · 07-31-2019, 01:27 PM

Quote:

Originally Posted by JARblue

So the Lexus is all buttoned up now and driving well. But I noticed my wheel studs seem to be a little off as seen in the photo (LH front) - they are shifted to one side of the opening as though they were torqued by hard acceleration. I know the Lexus is a V6 but it's not that powerful lol. I managed to get the wheel back on without too much issue but I did have to start threading the lug nuts with the wheel at an angle to keep the lugs from binding. Everything tightened down smoothly and several test drives at various speeds do not indicate any problems. In hindsight I'm thinking I should have taken a dead blow hammer to the studs to see if they were at all loose, although I wasn't able to move them just with my hand.

Any thoughts? Concerns?

It looks like the rotor might not be precisely right for the car. To my half-blind azz, it looks like the space to the one side of each stud is pretty much the same, which leads me to believe it might not be the right one for the car. It should fit without the extra space.

JLarson · 07-31-2019, 01:39 PM

Quote:

Originally Posted by jwick

What are you pouring?

A mixture of semen and Jimmy Hoffa today, back to concrete again tomorrow!

sx moneypit · 07-31-2019, 01:48 PM

Quote:

Originally Posted by JARblue

So the Lexus is all buttoned up now and driving well. But I noticed my wheel studs seem to be a little off as seen in the photo (LH front) - they are shifted to one side of the opening as though they were torqued by hard acceleration. I know the Lexus is a V6 but it's not that powerful lol. I managed to get the wheel back on without too much issue but I did have to start threading the lug nuts with the wheel at an angle to keep the lugs from binding. Everything tightened down smoothly and several test drives at various speeds do not indicate any problems. In hindsight I'm thinking I should have taken a dead blow hammer to the studs to see if they were at all loose, although I wasn't able to move them just with my hand.

Any thoughts? Concerns?

The rotor fitment looks good to me.The rotors are always drilled a little bigger than the studs.You may not have had the wheel fully seated when you installed the lug nuts.

-ZS-Carpenter · 07-31-2019, 03:51 PM

Quote:

Originally Posted by jwick

What are you pouring?

Airiation floors for a grain bin

Sent from my SM-G965U using Tapatalk

Zezus · 07-31-2019, 04:43 PM

Turns out the idler on the civic didn't like 9k rpm.. was 5 mins from home so I hope I didn't get it too hot

Sent from my SM-G965U using Tapatalk

Rusty · 07-31-2019, 05:01 PM

Quote:

Originally Posted by JARblue

So the Lexus is all buttoned up now and driving well. But I noticed my wheel studs seem to be a little off as seen in the photo (LH front) - they are shifted to one side of the opening as though they were torqued by hard acceleration. I know the Lexus is a V6 but it's not that powerful lol. I managed to get the wheel back on without too much issue but I did have to start threading the lug nuts with the wheel at an angle to keep the lugs from binding. Everything tightened down smoothly and several test drives at various speeds do not indicate any problems. In hindsight I'm thinking I should have taken a dead blow hammer to the studs to see if they were at all loose, although I wasn't able to move them just with my hand.

Any thoughts? Concerns?

Quote:

Originally Posted by Ghostvette

It looks like the rotor might not be precisely right for the car. To my half-blind azz, it looks like the space to the one side of each stud is pretty much the same, which leads me to believe it might not be the right one for the car. It should fit without the extra space.

Quote:

Originally Posted by sx moneypit

The rotor fitment looks good to me.The rotors are always drilled a little bigger than the studs.You may not have had the wheel fully seated when you installed the lug nuts.

That's normal. Typical fitment of rotor to hub.

Rusty · 07-31-2019, 05:03 PM

Quote:

Originally Posted by JLarson

A mixture of semen and Jimmy Hoffa today, back to concrete again tomorrow!

Jimmy Hoffa isn't where you think he is.

jchammond · 07-31-2019, 05:32 PM

Home,getting some rain & I’m gonna grab a nap

I’ll catch up later

madwi · 07-31-2019, 07:53 PM

I opened my to-do list at list at work and it looked to be a mile long and my lazy heart sank. Started to really look at it and its a bunch of crap that doesnt take a lot of effort.

I can go back to the interwebs for a while

BettyZ · 07-31-2019, 08:28 PM

Quote:

Originally Posted by old guy

Betty, what's the total mileage so far ?

4,983 freedom-miles.

Sent from my SM-G955U using Tapatalk

Spooler · 07-31-2019, 08:38 PM

One of the best car stories you will ever hear.

-ZS-Carpenter · 07-31-2019, 08:52 PM

182 yards of semen and Jimmy Hoffa poured today

Who's buying the beers

Rusty · 07-31-2019, 09:07 PM

Korean Face Mask

Rusty · 07-31-2019, 09:08 PM

Quote:

Originally Posted by Zezus

Turns out the idler on the civic didn't like 9k rpm.. was 5 mins from home so I hope I didn't get it too hot

Sent from my SM-G965U using Tapatalk

That didn't go well.

07-31-2019, 04:43 PM	#6351 (permalink)
Zezus Enthusiast Member Join Date: Dec 2018 Location: Cincinnati Posts: 354 Drives: 2016 370z sport 6spd Rep Power: 50338	Turns out the idler on the civic didn't like 9k rpm.. was 5 mins from home so I hope I didn't get it too hot Sent from my SM-G965U using Tapatalk Ghostvette, old guy and BettyZ like this.

07-31-2019, 05:32 PM	#6354 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	Home,getting some rain & I’m gonna grab a nap I’ll catch up later old guy likes this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

07-31-2019, 07:53 PM	#6355 (permalink)
madwi A True Z Fanatic Join Date: Sep 2012 Location: West Michigan Posts: 31,410 Drives: Granma red Z Rep Power: 2684429	I opened my to-do list at list at work and it looked to be a mile long and my lazy heart sank. Started to really look at it and its a bunch of crap that doesnt take a lot of effort. I can go back to the interwebs for a while Rusty and old guy like this.

07-31-2019, 08:38 PM	#6357 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,805 Drives: 2013 Nismo 370z Rep Power: 2684392	One of the best car stories you will ever hear. Rusty, Hotrodz, Ghostvette and 3 others like this.

07-31-2019, 08:52 PM	#6358 (permalink)
-ZS-Carpenter A True Z Fanatic Join Date: Sep 2016 Location: Illinois Posts: 2,410 Drives: 13 370z 6MT Rep Power: 2684367	182 yards of semen and Jimmy Hoffa poured today Who's buying the beers Rusty, Ghostvette, Spooler and 4 others like this.

07-31-2019, 09:07 PM	#6359 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,192 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Korean Face Mask __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) Cooking Edition	Leingod	The Lounge (Off Topic)	319	09-28-2021 11:10 PM
The New "What did you do with your Z today" (with off topic replies) XXVI	JARblue	The Lounge (Off Topic)	10020	04-23-2017 12:37 PM
The New "What did you do with your Z today" (with off topic replies) XVIII	eastwest2300	The Lounge (Off Topic)	10000	07-09-2015 08:48 PM