The New "What did you do with your Z today" (with off topic replies) XXXII

Pintsize725 · 05-01-2019, 11:44 PM

JARblue · 05-02-2019, 12:05 AM

I'm having a hard time getting motivated to clean up the garage so I can actually work in it

JARblue · 05-02-2019, 12:08 AM

I did manage to recover all of the nuts from the aerocatch latch mounting plates. So I finally mounted both of the CF finish latches to replace the faded black ones that were already on the hood

Rusty · 05-02-2019, 12:25 AM

Quote:

Originally Posted by JARblue

I'm having a hard time getting motivated to clean up the garage so I can actually work in it

I made a mess in mine from the carbon fiber splitter, fender vents, rear sub-frame bushing. Grinding, welding, drilling, cutting. I need to have it cleaned up and my Z on the ground before Lein gets here.

madwi · 05-02-2019, 01:46 AM

Quote:

Originally Posted by Rusty

Had busy day.

The splitter is almost finished. Have to figure out a splash shield in the fender well. Have almost one FE Design fender vent installed. The hole is cut, trimmed, vent fitted, inside of the fender painted black. What is left is to drill the mounting holes and bolt down, wax fender. Then start on the other side.

Document the fender vent install. I have mine to do here very shortly.

madwi · 05-02-2019, 01:47 AM

Quote:

Originally Posted by Pintsize725

hey Pint.

Rusty · 05-02-2019, 02:07 AM

Quote:

Originally Posted by madwi

Document the fender vent install. I have mine to do here very shortly.

Position carefully. I got mine up a little too high on the fender. I'm about 1 1/2" down from the top roll of the fender. Maybe should have been down about 2 1/2 ". Everything fits flush but the bottom curve of the vent. Have about 1/4"gap that I have to play with. And cut the outside edge of the temp plate. Even doing that. I still had to made the hole bigger to get the vent into the hole.

Do you have the temp plates?

madwi · 05-02-2019, 02:11 AM

Quote:

Originally Posted by Rusty

Position carefully. I got mine up a little too high on the fender. I'm about 1 1/2" down from the top roll of the fender. Maybe should have been down about 2 1/2 ". Everything fits flush but the bottom curve of the vent. Have about 1/4"gap that I have to play with. And cut the outside edge of the temp plate. Even doing that. I still had to made the hole bigger to get the vent into the hole.

Do you have the temp plates?

yeah, I have the 3d printed templates. I was holding the template up the other day looking for a good position. I was about where you were, 1.5" from the top. Ill look into dropping it a bit.

jchammond · 05-02-2019, 02:11 AM

madwi · 05-02-2019, 02:12 AM

Quote:

Originally Posted by jchammond

jchammond · 05-02-2019, 03:18 AM

Quote:

Originally Posted by madwi

Can’t Sleep

Rusty · 05-02-2019, 03:46 AM

Quote:

Originally Posted by Rusty

Position carefully. I got mine up a little too high on the fender. I'm about 1 1/2" down from the top roll of the fender. Maybe should have been down about 2 1/2 ". Everything fits flush but the bottom curve of the vent. Have about 1/4"gap that I have to play with. And cut the outside edge of the temp plate. Even doing that. I still had to made the hole bigger to get the vent into the hole.

Do you have the temp plates?

I typed this wrong. It should be the inside of the temp plate, on the outside of your mark.

Rusty · 05-02-2019, 03:48 AM

Quote:

Originally Posted by jchammond

Can’t Sleep

Same here. Went to bed, but just kept rolling. Restless legs. Don't know what to do with them sometimes.

Drinking big glass of chocolate milk.

jchammond · 05-02-2019, 04:21 AM

Quote:

Originally Posted by Rusty

Same here. Went to bed, but just kept rolling. Restless legs. Don't know what to do with them sometimes.

Drinking big glass of chocolate milk.

I went ahead & got up...pusky noticed that i was awake & wanted some attention

Got my coffee & paying some bills,,,while occasionally glancing over at the stack of Benjamin’s for this afternoon

madwi · 05-02-2019, 05:50 AM

05-01-2019, 11:44 PM	#8716 (permalink)
Pintsize725 A True Z Fanatic Join Date: Jan 2012 Location: Austin Posts: 14,196 Drives: 2016 Mazda 6 Rep Power: 211844	jchammond and BettyZ like this. __________________ Tracie

05-02-2019, 12:05 AM	#8717 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	I'm having a hard time getting motivated to clean up the garage so I can actually work in it Rusty, madwi, Ghostvette and 2 others like this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

05-02-2019, 12:08 AM	#8718 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	I did manage to recover all of the nuts from the aerocatch latch mounting plates. So I finally mounted both of the CF finish latches to replace the faded black ones that were already on the hood Rusty, madwi and Ghostvette like this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

05-02-2019, 02:11 AM	#8724 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	__________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

05-02-2019, 05:50 AM	#8730 (permalink)
madwi A True Z Fanatic Join Date: Sep 2012 Location: West Michigan Posts: 31,410 Drives: Granma red Z Rep Power: 2684429	jchammond likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) Cooking Edition	Leingod	The Lounge (Off Topic)	319	09-28-2021 11:10 PM
The New "What did you do with your Z today" (with off topic replies) XXVIII	JARblue	The Lounge (Off Topic)	10014	04-26-2018 11:07 AM
The New "What did you do with your Z today" (with off topic replies) XXVII	JARblue	The Lounge (Off Topic)	9999	11-26-2017 08:08 AM
The New "What did you do with your Z today" (with off topic replies) XIII	JARblue	The Lounge (Off Topic)	10011	08-04-2014 05:16 PM