The New "What did you do with your Z today" (with off topic replies) XXXII

bunk · 04-14-2019, 04:23 PM

Quote:

Originally Posted by Rusty

That burr will not let it reverse directions. Going backward will make the burr bigger.

Ah. Gotcha. Point of no return then. BFH and a 10-12" bolt or cut some all thread to length.

Rusty · 04-14-2019, 04:47 PM

I know all about burrs. I have ruined a few things over the years. Like a $80,000 coupling for a shaft.

Coupling was a interference fit. Meaning the bore of the coupling was smaller then the diameter of the shaft it was going on. Shaft diameter 12.000". Bore diameter 11.980", 0.020" smaller. Have to heat the coupling up to expand the bore diameter. Heat it 600F to grow the bore to 12.010". Start to slide the coupling over the shaft. Coupling started to cool off. Picked up a burr about 90% of the way on. Stop the coupling dead in it's tracks. Hurried up and threw more heat to the coupling with 3 rose bud torches. Stuck! End up machining off the coupling and ordering a new coupling.

What saved my bacon on that job. I had the foreman right there with me, giving me a hand.

What makes the diff bushing install hard is that it just like the above, but without the heat. And the sub-frame hole is not perfectly round either. It's somewhat egg shaped from the welding on the sub-frame.

jchammond · 04-14-2019, 06:28 PM

Quote:

Originally Posted by Rusty

He installed the diff bushing from the rear, instead of the front of the sub-frame. So he doesn't have to much room the swing.

I’ve stuck 2 in from the rear

Zingston · 04-14-2019, 06:30 PM

Quote:

Originally Posted by jchammond

I’ve stuck 2 in from the rear

jchammond · 04-14-2019, 06:31 PM

Quote:

Originally Posted by bunk

Now its not backing out either..lol

Keep going; while pulling in with the bolt, occasionally smack the bushing side with a 5# hammer

Rusty · 04-14-2019, 06:43 PM

Quote:

Originally Posted by jchammond

I’ve stuck 2 in from the rear

Backdoor man. A Rump Raider. Butt Pirate.

bunk · 04-14-2019, 06:49 PM

Quote:

Originally Posted by jchammond

Keep going; while pulling in with the bolt, occasionally smack the bushing side with a 5# hammer

I'm gonna keep chugging at forcing that B in. just picked up an entry level BFH, 32oz. If that doesnt work, I'll rent a 3# sliding hammer from autozone, if that shaft is 1/2", otherwise I'll have to find thor's hammer

eastwest2300 · 04-14-2019, 07:09 PM

Quote:

Originally Posted by Zingston

eastwest2300 · 04-14-2019, 07:10 PM

Quote:

Originally Posted by bunk

I'm gonna keep chugging at forcing that B in. just picked up an entry level BFH, 32oz. If that doesnt work, I'll rent a 3# sliding hammer from autozone, if that shaft is 1/2", otherwise I'll have to find thor's hammer

Zingston · 04-14-2019, 07:11 PM

Quote:

Originally Posted by eastwest2300

Hey EW, Bunk said 1/2 inch shaft.

jchammond · 04-14-2019, 07:21 PM

Quote:

Originally Posted by bunk

I'm gonna keep chugging at forcing that B in. just picked up an entry level BFH, 32oz. If that doesnt work, I'll rent a 3# sliding hammer from autozone, if that shaft is 1/2", otherwise I'll have to find thor's hammer

Thought that hole was a tad larger? 9/16” or maybe 5/8”

jchammond · 04-14-2019, 07:29 PM

Measure that hole Bunk

You could potentially get a larger threaded rod & nut to work with

Rusty · 04-14-2019, 07:29 PM

Quote:

Originally Posted by Zingston

Hey EW, Bunk said 1/2 inch shaft.

Need at least 6" of girth.

Rusty · 04-14-2019, 07:29 PM

Quote:

Originally Posted by jchammond

Measure that hole Bunk

You could potentially get a larger threaded rod & nut to work with

13mm is the biggest you can go.

Zingston · 04-14-2019, 07:33 PM

Quote:

Originally Posted by Rusty

Need at least 6" of girth.

EW always argues anything over 5 1/2 is just too much.

04-14-2019, 04:47 PM	#6467 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,279 Drives: 2011 Nismo GM 6M Rep Power: 2684438	I know all about burrs. I have ruined a few things over the years. Like a $80,000 coupling for a shaft. Coupling was a interference fit. Meaning the bore of the coupling was smaller then the diameter of the shaft it was going on. Shaft diameter 12.000". Bore diameter 11.980", 0.020" smaller. Have to heat the coupling up to expand the bore diameter. Heat it 600F to grow the bore to 12.010". Start to slide the coupling over the shaft. Coupling started to cool off. Picked up a burr about 90% of the way on. Stop the coupling dead in it's tracks. Hurried up and threw more heat to the coupling with 3 rose bud torches. Stuck! End up machining off the coupling and ordering a new coupling. What saved my bacon on that job. I had the foreman right there with me, giving me a hand. What makes the diff bushing install hard is that it just like the above, but without the heat. And the sub-frame hole is not perfectly round either. It's somewhat egg shaped from the welding on the sub-frame. bunk and BettyZ like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

04-14-2019, 07:29 PM	#6477 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	Measure that hole Bunk You could potentially get a larger threaded rod & nut to work with __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) Cooking Edition	Leingod	The Lounge (Off Topic)	319	09-28-2021 11:10 PM
The New "What did you do with your Z today" (with off topic replies) XXVIII	JARblue	The Lounge (Off Topic)	10014	04-26-2018 11:07 AM
The New "What did you do with your Z today" (with off topic replies) XXVII	JARblue	The Lounge (Off Topic)	9999	11-26-2017 08:08 AM
The New "What did you do with your Z today" (with off topic replies) XIII	JARblue	The Lounge (Off Topic)	10011	08-04-2014 05:16 PM