The New "What did you do with your Z today" (with off topic replies) XXXII

JARblue · 04-09-2019, 08:52 PM

Quote:

Originally Posted by jchammond

So does your azz

It's supposed to though

madwi · 04-09-2019, 08:54 PM

Quote:

Originally Posted by jchammond

So you’re really not pulling anyone’s leg

No. I am dead serious about being ****** up lol.

madwi · 04-09-2019, 08:58 PM

Quote:

Originally Posted by JARblue

The hood I'm picking up has a crack in it ... seller just told me and added photos to the thread

Appears to be a single longish crack and only in the resin. I expect it will be a relatively easy repair unless the fibers are damaged also.

eh, the corner was damaged on my seibon hood when it arrived. bodyshop said they would use resin and then blend it in with tinted clear.

JARblue · 04-09-2019, 08:59 PM

Now I just need to find a bodyshop

JARblue · 04-09-2019, 09:00 PM

And hope the guy doesn't mind if I show up at 8 am to pick up everything

Rusty · 04-09-2019, 09:01 PM

Quote:

Originally Posted by jchammond

Looking at those pictures. Think that I can install that easy. In the car.....................no.........

Rusty · 04-09-2019, 09:02 PM

Quote:

Originally Posted by madwi

No. I am dead serious about being ****** up lol.

Ain't that your natural state? SNAFU.

madwi · 04-09-2019, 09:05 PM

Quote:

Originally Posted by Rusty

Ain't that your natural state? SNAFU.

Welcome to my normal, it looks like this:

bunk · 04-09-2019, 09:18 PM

Quote:

Originally Posted by Rusty

Did you get squirted with silicone when you first start to cut with the hole saw?

There is 2 chambers in the bushing. One of them leaks everything out, while the other still has silicone in it. when you cut it, it squirts.

I used my big floor jack to lower and raise the diff. I had no problem doing mine, EW, and JL's.

Nope. It was bone dry!

bunk · 04-09-2019, 09:24 PM

Quote:

Originally Posted by Rusty

Good job.

Make sure there is nothing sticking up, and no burr's in the hole. Anything in there WILL cause you a headache. Put lots of anti-seize in the hole. And put the bushing in the freezer over night.

When you start to install the bushing. Make sure it goes in straight. You may have to take a hammer to tilt it. When pulling the bushing in. And the all thread gets tight. You can use a hammer to tap on the bushing/ The vibrations from tapping on it will help the bushing going in.

Looking back, getting the bushing out was easier than getting the new one in. I think I started it not perfectly centered and I'm at the point of no return.. I found a thick metal plate from home depot I'm using to tighten a bolt against hasn't bent. I need a ratcheting breaker bar. Been attacking this bolt for half an hour and not even half way. I'm calling it a night and regroup and finish saturday.

Rusty · 04-09-2019, 09:25 PM

Quote:

Originally Posted by bunk

Nope. It was bone dry!

You got lucky. Mine squirted about 3 ft. and Jl's squirted about 5 ft.

JL's got me good. My glasses, hair, tee shirt, face.

eastwest2300 · 04-09-2019, 09:32 PM

Quote:

Originally Posted by BoneZ

You are a good friend.

eastwest2300 · 04-09-2019, 09:32 PM

Quote:

Originally Posted by Leingod

I'll accept a 10% fee for my help selling it.

eastwest2300 · 04-09-2019, 09:33 PM

Quote:

Originally Posted by madwi

for the 50% fee +gas and toll money he is making I think he should drive it all the way there for the guy.

eastwest2300 · 04-09-2019, 09:33 PM

Quote:

Originally Posted by jchammond

04-09-2019, 08:59 PM	#5689 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 44 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	Now I just need to find a bodyshop __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

04-09-2019, 09:00 PM	#5690 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 44 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	And hope the guy doesn't mind if I show up at 8 am to pick up everything madwi likes this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) Cooking Edition	Leingod	The Lounge (Off Topic)	319	09-28-2021 11:10 PM
The New "What did you do with your Z today" (with off topic replies) XXVIII	JARblue	The Lounge (Off Topic)	10014	04-26-2018 11:07 AM
The New "What did you do with your Z today" (with off topic replies) XXVII	JARblue	The Lounge (Off Topic)	9999	11-26-2017 08:08 AM
The New "What did you do with your Z today" (with off topic replies) XIII	JARblue	The Lounge (Off Topic)	10011	08-04-2014 05:16 PM