The New "What did you do with your Z today" (with off topic replies) XXVIII

Rusty · 04-02-2018, 03:42 PM

Quote:

Originally Posted by JLarson

In PA they hit you for both mechanical and emissions inspections, usually about $80.

Not me. I'm in Fayette county. No emissions.

Helll, we don't even recycle. We don't have enough people in the township for that. Only have 3,600.

Rusty · 04-02-2018, 03:46 PM

Quote:

Originally Posted by Leingod

Guys...guys!!! In 2-3 weeks I MIGHT get my car out of storage!!! ...............

Insurance goes on tomorrow. State inspection Wednesday morning, alignment Wednesday afternoon.

eastwest2300 · 04-02-2018, 03:47 PM

Quote:

Originally Posted by Rusty

Insurance goes on tomorrow. State inspection Wednesday morning, alignment Wednesday afternoon.

dude.. im gonna text you a little later tonight...

Rusty · 04-02-2018, 03:52 PM

Quote:

Originally Posted by eastwest2300

dude.. im gonna text you a little later tonight...

Ok, about what time. I'm going to lay down for a little nap in about 10 minutes.

Rusty · 04-02-2018, 04:00 PM

The GT-R start button should not take you longer then 10 minutes to do. Pop up the cover around the shifter. Remove the one screw for each knee pad, and remove them. Then remove the 2 screws on the bottom of the center dash cover. One in each corner. Pop the cover from the bottom first. You will have about 4 to 5 inches of room to work with. Pop the plug on the back of the start pop. Push out to remove it. Push in the new one. Install the center dash pad from the top first. Just push it in. Then reinstall everything else.

eastwest2300 · 04-02-2018, 04:09 PM

Quote:

Originally Posted by Rusty

Ok, about what time. I'm going to lay down for a little nap in about 10 minutes.

830/9ish

Leingod · 04-02-2018, 04:09 PM

Quote:

Originally Posted by Rusty

The GT-R start button should not take you longer then 10 minutes to do. Pop up the cover around the shifter. Remove the one screw for each knee pad, and remove them. Then remove the 2 screws on the bottom of the center dash cover. One in each corner. Pop the cover from the bottom first. You will have about 4 to 5 inches of room to work with. Pop the plug on the back of the start pop. Push out to remove it. Push in the new one. Install the center dash pad from the top first. Just push it in. Then reinstall everything else.

Yup. Stupidly easy. Figured I'd give it to my girlfriend to figure out. She can handle the simplistic things while we are cursing at demon bolts and oil coolers. Figured you can handle the button, vinyl wrapping the pillars, and helping install the side blades or diffuser.

Her real test will be figuring out how to install the rjm clutch assembly with Madwi giving her directions. She is easily the tiniest and most flexible so hopefully it'll be easier.

Rusty · 04-02-2018, 04:18 PM

Quote:

Originally Posted by Leingod

Yup. Stupidly easy. Figured I'd give it to my girlfriend to figure out. She can handle the simplistic things while we are cursing at demon bolts and oil coolers. Figured you can handle the button, vinyl wrapping the pillars, and helping install the side blades or diffuser.

Her real test will be figuring out how to install the rjm clutch assembly with Madwi giving her directions. She is easily the tiniest and most flexible so hopefully it'll be easier.

Have to watch on the start button. The tabs that hold the plug in CAN break REAL easy. Want to know how I know? Don't ask.

Leingod · 04-02-2018, 04:31 PM

I figured she could try it the simpler way.

GTR start button! another alternative..

Rusty · 04-02-2018, 04:36 PM

Quote:

Originally Posted by Leingod

I figured she could try it the simpler way.

GTR start button! another alternative..

That will do it.

I'm just so used to taking the center pad off to get to the wiring behind it when i was installing my gauges.

StevenSlice · 04-02-2018, 04:50 PM

I learned how to do some of my own maintenance last night, since most of the **** we installed on the Z wasnt me but friends, while i was the assistant / doing the little things. (Gotta start somewhere right)

Learned to bleed brakes, and how to work a Vice because the retainer clips were bent, explaining why it always darted to the side on initial braking.

Rolled under the car, made sure everything was tight and found the source of my dropping of goop(Diff bushing is starting to go).

Adjusted the coilovers, lowered it / gave it some more pre-load.

Gonna throw camber in it tonight by using a caliper gauge and do my best, since the shop i took it too for an alignment was incompetent and couldn't give me the camber i needed. Told them how to adjust it, and still couldnt do it.

Race prep for next weekend, basically complete.

onzedge · 04-02-2018, 05:16 PM

Quote:

Originally Posted by StevenSlice

I learned how to do some of my own maintenance last night, since most of the **** we installed on the Z wasnt me but friends, while i was the assistant / doing the little things. (Gotta start somewhere right)

Learned to bleed brakes, and how to work a Vice because the retainer clips were bent, explaining why it always darted to the side on initial braking.

Rolled under the car, made sure everything was tight and found the source of my dropping of goop(Diff bushing is starting to go).

Adjusted the coilovers, lowered it / gave it some more pre-load.

Gonna throw camber in it tonight by using a caliper gauge and do my best, since the shop i took it too for an alignment was incompetent and couldn't give me the camber i needed. Told them how to adjust it, and still couldnt do it.

Race prep for next weekend, basically complete.

Rep Freely

JARblue · 04-02-2018, 05:25 PM

Quote:

Originally Posted by Rusty

The GT-R start button should not take you longer then 10 minutes to do.

And that includes a 9 minute nap

Just pop it out with a panel removal tool. Takes about 10 seconds.

jchammond · 04-02-2018, 05:26 PM

Quote:

Originally Posted by Rusty

Be careful and easy into things. Don't rush it.

The day went pretty smooth,,,a tad of soreness around my waist.
Now about to change oil in my daughters car......She made some last minute plans on me.
You know daddy can't say no; so this ought to be fun,,after easing through a 9hr day.

Leingod · 04-02-2018, 07:01 PM

Scrapped together a quick putanesca sauce while I let some homemade dough rise and now everything is in the oven for some quick and dirty cast iron pizza.

04-02-2018, 04:00 PM	#7895 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,164 Drives: 2011 Nismo GM 6M Rep Power: 2684437	The GT-R start button should not take you longer then 10 minutes to do. Pop up the cover around the shifter. Remove the one screw for each knee pad, and remove them. Then remove the 2 screws on the bottom of the center dash cover. One in each corner. Pop the cover from the bottom first. You will have about 4 to 5 inches of room to work with. Pop the plug on the back of the start pop. Push out to remove it. Push in the new one. Install the center dash pad from the top first. Just push it in. Then reinstall everything else. eastwest2300, Hotrodz and Spoiler like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

04-02-2018, 04:31 PM	#7899 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,060 Drives: In Circles Rep Power: 2684396	I figured she could try it the simpler way. GTR start button! another alternative.. eastwest2300 and Ghostvette like this. __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

04-02-2018, 04:50 PM	#7901 (permalink)
StevenSlice Track Member Join Date: Jun 2017 Location: Lompoc, CA Age: 27 Posts: 502 Drives: Like an idiot Rep Power: 46199	I learned how to do some of my own maintenance last night, since most of the **** we installed on the Z wasnt me but friends, while i was the assistant / doing the little things. (Gotta start somewhere right) Learned to bleed brakes, and how to work a Vice because the retainer clips were bent, explaining why it always darted to the side on initial braking. Rolled under the car, made sure everything was tight and found the source of my dropping of goop(Diff bushing is starting to go). Adjusted the coilovers, lowered it / gave it some more pre-load. Gonna throw camber in it tonight by using a caliper gauge and do my best, since the shop i took it too for an alignment was incompetent and couldn't give me the camber i needed. Told them how to adjust it, and still couldnt do it. Race prep for next weekend, basically complete. onzedge, Rusty and Ghostvette like this. __________________ Kansei Corsa \| Endless \| Winmax \| Hotchkis \| ISR Performance \| SPL Parts \| Voodoo13 \|Sabelt \| PowerTrix \| Corner 3 \|

04-02-2018, 07:01 PM	#7905 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,060 Drives: In Circles Rep Power: 2684396	Scrapped together a quick putanesca sauce while I let some homemade dough rise and now everything is in the oven for some quick and dirty cast iron pizza. __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) XXVII	JARblue	The Lounge (Off Topic)	9999	11-26-2017 08:08 AM
The New "What did you do with your Z today" (with off topic replies) XXIV	JARblue	The Lounge (Off Topic)	10059	08-17-2016 01:08 PM
The New "What did you do with your Z today" (with off topic replies) XXIII	eastwest2300	The Lounge (Off Topic)	10001	06-23-2016 10:21 AM
The New "What did you do with your Z today" (with off topic replies) XXII	eastwest2300	The Lounge (Off Topic)	10001	04-05-2016 09:15 PM
The New "What did you do with your Z today" (with off topic replies) XVIII	eastwest2300	The Lounge (Off Topic)	10000	07-09-2015 08:48 PM