The New "What did you do with your Z today" (with off topic replies) XXII

Leingod · 03-02-2016, 01:59 PM

Quote:

Originally Posted by kenchan

nice.. i noticed u hadn't asked about 15:30 so i was getting kinda jelly..

the actual jack point on the side is the hump behind the pinch rail. i place a piece of wood on my hydraulic jack platform and place the weight just behind the two cutouts.

if you want to use those for jack stands u need to lift the car from the front under the engine area where u see the cross brace jack point.

I looked at an old photo of mine. I used a jack on the pinch rail and literally right beside the jack, i placed my jackstand. Both probably on the pinch rail knowing my dumbness. My current jack doesn't fit under the front of the car. Was looking into getting a low profile jack.

Quote:

Originally Posted by kenchan

but i recommend u get some ramps and use dat instead. goes much faster..

Do you have a link of the appropriate length i'd need sicne I read a lot of people hit the front chin on them.

Ghostvette · 03-02-2016, 02:00 PM

A set of race ramps are next on the list. Since the space in the garage at my apartment is kinda narrow, it will be easier to back the car out, set the ramps, then drive up to change the oil. Now to figure out where to store them....

kenchan · 03-02-2016, 02:00 PM

u guys use the puck? i was thinking about getting one dat was pre-cut.. but havent

kenchan · 03-02-2016, 02:01 PM

Quote:

Originally Posted by Ghostvette

A set of race ramps are next on the list. Since the space in the garage at my apartment is kinda narrow, it will be easier to back the car out, set the ramps, then drive up to change the oil. Now to figure out where to store them....

yah, raceramps are the shitts. they are excellent quality, light weight, does not slide around, easy to wash, etc. im going to be putting my wife's dd on there too maybe next weekend to wash the undercarriage real nice.

njobe89 · 03-02-2016, 02:02 PM

Quote:

Originally Posted by kenchan

nice.. i noticed u hadn't asked about 15:30 so i was getting kinda jelly..

the actual jack point on the side is the hump behind the pinch rail. i place a piece of wood on my hydraulic jack platform and place the weight just behind the two cutouts.

if you want to use those for jack stands u need to lift the car from the front under the engine area where u see the cross brace jack point.

oh i'm here daily to make you jelly of 15:30

tomorrow i think i'll leave at 15:00

and friday i'll work from home

Leingod · 03-02-2016, 02:06 PM

These? Idk what to order...

http://www.amazon.com/Race-Ramps-RR-...rds=race+ramps

kenchan · 03-02-2016, 02:20 PM

Quote:

Originally Posted by njobe89

oh i'm here daily to make you jelly of 15:30

tomorrow i think i'll leave at 15:00

and friday i'll work from home

haha!

but im off on friday too.

Leingod · 03-02-2016, 02:21 PM

Ordering these.

http://www.amazon.com/Race-Ramps-RR-...rds=race+ramps

kenchan · 03-02-2016, 02:22 PM

RR-56-56" and use the RR-EX-12 56"Xtender

kenchan · 03-02-2016, 02:24 PM

without the xtender the ings would hit the ramp.

Masterbeatty · 03-02-2016, 02:25 PM

I use left over base board pieces to lift mine up. Nails and glue work good so far.

kenchan · 03-02-2016, 02:27 PM

Quote:

Originally Posted by Leingod

I looked at an old photo of mine. I used a jack on the pinch rail and literally right beside the jack, i placed my jackstand. Both probably on the pinch rail knowing my dumbness. My current jack doesn't fit under the front of the car. Was looking into getting a low profile jack.

Do you have a link of the appropriate length i'd need sicne I read a lot of people hit the front chin on them.

yah, dont place the weight of the car on the pinch rail as the rail will bend.

u can source a low profile aluminum hydraulic jack at harbor freight. i have two of them.

Leingod · 03-02-2016, 02:29 PM

Quote:

Originally Posted by kenchan

yah, dont place the weight of the car on the pinch rail as the rail will bend.

u can source a low profile aluminum hydraulic jack at harbor freight. i have two of them.

Was thinking of taking a run to harbor freight anyways. A low profile for under $100 or raceramps for $250+.

kenchan · 03-02-2016, 02:30 PM

btw, leon... i call the pinch weld 'rails', but just letting u know the proper terminology is pinch weld.

kenchan · 03-02-2016, 02:31 PM

Quote:

Originally Posted by Leingod

Was thinking of taking a run to harbor freight anyways. A low profile for under $100 or raceramps for $250+.

mine was like $79 at the time. it's blue housing. i just bought two of them since they were so cheap.

03-02-2016, 02:00 PM	#5132 (permalink)
Ghostvette A True Z Fanatic Join Date: Aug 2013 Location: Shawnee KS Posts: 5,698 Drives: 15 Magma Red 6MT Rep Power: 2684377	A set of race ramps are next on the list. Since the space in the garage at my apartment is kinda narrow, it will be easier to back the car out, set the ramps, then drive up to change the oil. Now to figure out where to store them.... __________________ 2015 Magma Red 6MT Sport Tech/2012 Fairlady MB 6MT Base (RIP 08032018)https://www.nicoclub.com/FSM/370Z/Coupe/

03-02-2016, 02:06 PM	#5136 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,057 Drives: In Circles Rep Power: 2684396	These? Idk what to order... http://www.amazon.com/Race-Ramps-RR-...rds=race+ramps __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

03-02-2016, 02:21 PM	#5138 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,057 Drives: In Circles Rep Power: 2684396	Ordering these. http://www.amazon.com/Race-Ramps-RR-...rds=race+ramps Ghostvette likes this. __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

03-02-2016, 02:25 PM	#5141 (permalink)
Masterbeatty A True Z Fanatic Join Date: May 2012 Location: Whales Vagina Posts: 4,586 Drives: the speed limit... Rep Power: 122867	I use left over base board pieces to lift mine up. Nails and glue work good so far. kenchan likes this. __________________ 2011 MB 6MT Masterbeatty journal

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 08:57 AM
The New "What did you do with your Z today" (with off topic replies) XVIII	eastwest2300	The Lounge (Off Topic)	10000	07-09-2015 07:48 PM
The New "What did you do with your Z today" (with off topic replies) XVII	eastwest2300	The Lounge (Off Topic)	10129	05-21-2015 09:30 AM
The New "What did you do with your Z today" (with off topic replies) XIII	JARblue	The Lounge (Off Topic)	10011	08-04-2014 04:16 PM
The New "What did you do with your Z today" (with off topic replies) VIII	JARblue	The Lounge (Off Topic)	10016	11-10-2013 11:21 AM

03-02-2016, 02:00 PM	#5133 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	u guys use the puck? i was thinking about getting one dat was pre-cut.. but havent

03-02-2016, 02:22 PM	#5139 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	RR-56-56" and use the RR-EX-12 56"Xtender

03-02-2016, 02:24 PM	#5140 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	without the xtender the ings would hit the ramp.

03-02-2016, 02:30 PM	#5144 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	btw, leon... i call the pinch weld 'rails', but just letting u know the proper terminology is pinch weld.