New Soho Single exit for the 370z!!

aszyd · 08-29-2014, 02:09 PM

Very nice! Combine that with an aftermarket Y pipe and it will be a true catback. Perhaps they should consider optioning in an additional resonator on the long center pipe.

Gregor12 · 08-29-2014, 04:35 PM

Quote:

Originally Posted by aszyd

Very nice! Combine that with an aftermarket Y pipe and it will be a true catback. Perhaps they should consider optioning in an additional resonator on the long center pipe.

you can get it with a resonator installed! they offer that too. and theyre installing their ypipe and dyno testing it soon as well...

1slow370 · 08-29-2014, 04:30 PM

Y PIPE BACK SINGLE MUFFLER FOR $700? My Berk full cat-back only cost me $900 and is basically double what you are buying here. If it were single 4" maybe i could see that but 3" pipe flows less than dual 2.5 there website says they picked up 8 whole horsepower with an exhaust AND tune.

Gregor12 · 08-29-2014, 04:42 PM

Quote:

Originally Posted by 1slow370

Y PIPE BACK SINGLE MUFFLER FOR $700? My Berk full cat-back only cost me $900 and is basically double what you are buying here. If it were single 4" maybe i could see that but 3" pipe flows less than dual 2.5 there website says they picked up 8 whole horsepower with an exhaust AND tune.

my car made the 298 (4th) with just the exhaust and no tune. stock y pipe, stock cats and stock intakes.. from what i see the berk cat back and Berk high flow cats didn't even make that!! my car made much less power with the stock exhaust. its not a comparison to stock but he is showing the with just the y pipe back section the car made 306 at the wheels.

as for flow the y-pipe is the choke point on these vehicles no matter what size it is the y pipe will still restrict it. so unless you have a true dual 2.5 inch then you're not actually flowing more than a single three. The numbers dont lie man! i was very very surprised what my car made with just a y-back on it. also he didn't tune for power. i asked soho to smooth out my fuel table because it was leaning out at the top so he did. still has room for more! they have a 8XX rwhp g with a single exit exhaust i dont think we should be worried lol

as for the exhaust price i thought it was really good for the overall gains and sound

1slow370 · 08-29-2014, 05:38 PM

Quote:

Originally Posted by Gregor12

my car made the 298 with just the exhaust and no tune.. it made much less power with the stock exhaust. its not a comparison to stock but he is showing the with just the y pipe the car made 306 at the wheels.

as for flow the y-pipe is the choke point on these vehicles no matter what size it is the y pipe will still restrict it. so unless you have a true dual 2.5 inch then you're not actually flowing more than a single three. The numbers dont lie man! i was very very surprised what my car made with just a y-back on it. also he didn't tune for power. i asked soho to smooth out my fuel table so he did. still has room for more! they have a 8XX rwhp g with a single exit exhaust i dont think we should be worried lol

as for the exhaust price i thought it was really good for the overall gains and sound

I do have a true dual 2.5, almost every other exhaust on the market is dual 2.5 or dual 3" and his 8xxwhp car is DEFINITELY over single 3" capacity. A dual 3" picks 40-50hp over a dual 2.5" on turbo z's that are only in the 500whp range I couldn't imagine how choked that car must be. Hell a stillen exhaust picks up 10-15 hp NO "smoothing the fuel curve" needed. I used to know a guy with a supra and he went up almost 150hp when he threw out his single 3" it took him from 750-almost 900hp going to a 4" But regardless there was what a week of R&D and maybe $200 in parts in this? It's not even polished

Edit: I got to throw in that hes using an intake t bolt clamp instead of a real exhaust band clamp as well because a t bolt is $3 and a real accuseal clamp is $12

Gregor12 · 08-29-2014, 05:51 PM

Quote:

Originally Posted by 1slow370

I do have a true dual 2.5, almost every other exhaust on the market is dual 2.5 or dual 3" and his 8xxwhp car is DEFINITELY over single 3" capacity. A dual 3" picks 40-50hp over a dual 2.5" on turbo z's that are only in the 500whp range I couldn't imagine how choked that car must be. Hell a stillen exhaust picks up 10-15 hp NO "smoothing the fuel curve" needed. I used to know a guy with a supra and he went up almost 150hp when he threw out his single 3" it took him from 750-almost 900hp going to a 4" But regardless there was what a week of R&D and maybe $200 in parts in this? It's not even polished

Edit: I got to throw in that hes using an intake t bolt clamp instead of a real exhaust band clamp as well because a t bolt is $3 and a real accuseal clamp is $12

Lol man idk why you're hating on the exhaust so much. And no there aren't that many actual true dual exhausts on the market. Your exhaust joins at the xpipe right??. It is what it is. I liked it and bought it so I just thought I would share it. And they have a single 3.5 inch on the g. That's my bad. Regardless. I still made more power for less compared to the berk exhaust. And it weighs less. And 200 bucks seriously??? Go build your own custom exhaust and see how much money it will cost lol I'll buy there y pipe and test pipes and **** on the berk system haha 296 with high flow cats and a dual catback is a joke. I made more in 4th for a few hundred less dollars. That's what I wanted so that why I bought it. As for the clamp it's worked very well so far and it left no slack when I installed it. Jerked on the exhaust a few times to see if it would budge. Over all I'm impressed with the exhaust. Just my opinion

synolimit · 02-16-2015, 04:58 AM

Quote:

Originally Posted by Gregor12

my car made the 298 (4th) with just the exhaust and no tune. stock y pipe, stock cats and stock intakes.

Quote:

Originally Posted by Gregor12

made 320rwhp and 270lb/ft with the stock intakes, stock cats, and factory tune!

Wait I'm so confused now.

Japanjay · 08-29-2014, 05:12 PM

What was your stock whp number?

Gregor12 · 08-29-2014, 05:16 PM

i didn't dyno mine stock. didnt get around to it but considering all 370z's put down 270-280 on a dyno jet stock i'm guessing it was around there!

1slow370 · 08-29-2014, 06:47 PM

Hey it's all opinion if it gets your rocks off go for it, but you paid too much. Here are what his cost should be on this Vibrant 1062 - $98, 5 ft of 3" 304 $110 with bends (or ~$60 if he gets them mandrel bent), T-bolt clamp $3, hardware $1, Flange $12, Gasket $3.25, and $30-50 overhead to pay someone to make 5 welds. So 250-270 and if goes with mandrel bending it will save roughly $100 a pipe. I could have this made with a beter muffler and tip, a vband instead of a coupler clamp, and get it polished for $250. Also an X pipe doesn't reduce the CSA of twin 2.5" tubing just as an FYI the pipes cross each other there is no choke it actually increases overall flow due to harmonics. I would not call that a finished version by a long shot if he made it better by putting a bit more work into the quality of it i would have no complaints but hey someone will pay for it.

Gregor12 · 08-29-2014, 11:49 PM

Quote:

Originally Posted by 1slow370

Hey it's all opinion if it gets your rocks off go for it, but you paid too much. Here are what his cost should be on this Vibrant 1062 - $98, 5 ft of 3" 304 $110 with bends (or ~$60 if he gets them mandrel bent), T-bolt clamp $3, hardware $1, Flange $12, Gasket $3.25, and $30-50 overhead to pay someone to make 5 welds. So 250-270 and if goes with mandrel bending it will save roughly $100 a pipe. I could have this made with a beter muffler and tip, a vband instead of a coupler clamp, and get it polished for $250. Also an X pipe doesn't reduce the CSA of twin 2.5" tubing just as an FYI the pipes cross each other there is no choke it actually increases overall flow due to harmonics. I would not call that a finished version by a long shot if he made it better by putting a bit more work into the quality of it i would have no complaints but hey someone will pay for it.

Hey man sorry you feel that way. 700 bucks wasn't **** to me for a good sounding single exit exhaust that made 300hp and shredded some weight. You need to add about 150 more dollars at least to your list though. The muffler is 200. And 30 bucks? What you think. It all comes pre cut and lined up haha don't forget they have to pay to ship it and ****. I thought it was a good deal anyways. To each his own man. They brought something cool to our community. No need to bash it and act like they're ripping people off. It's 700 dollars for a good exhaust.

Phil

Sent from my iPad using Tapatalk HD

1slow370 · 08-30-2014, 12:36 PM

Quote:

Originally Posted by Gregor12

Hey man sorry you feel that way. 700 bucks wasn't **** to me for a good sounding single exit exhaust that made 300hp and shredded some weight. You need to add about 150 more dollars at least to your list though. The muffler is 200. And 30 bucks? What you think. It all comes pre cut and lined up haha don't forget they have to pay to ship it and ****. I thought it was a good deal anyways. To each his own man. They brought something cool to our community. No need to bash it and act like they're ripping people off. It's 700 dollars for a good exhaust.

Phil

Sent from my iPad using Tapatalk HD

dude i pulled those numbers straight from my price sheets, i place orders with fab shops, i used to track efficiency on an in house welding and fab cell, if soho is spending more than that they are buying the parts from the wrong vender or they have some efficiency issues to look into

Sent from my HTCONE using Tapatalk

Gregor12 · 08-30-2014, 02:16 PM

Quote:

Originally Posted by 1slow370

dude i pulled those numbers straight from my price sheets, i place orders with fab shops, i used to track efficiency on an in house welding and fab cell, if soho is spending more than that they are buying the parts from the wrong vender or they have some efficiency issues to look into

Sent from my HTCONE using Tapatalk

Gotcha. Well I have no idea haha I just bought the exhaust because I liked it and I know they do very good work. Oh yea. And I hit 300whp for 700 bucks and lost some weight. So it's awesome in my opinion

Sent from my iPad using Tapatalk HD

Aardwolf · 09-07-2014, 06:42 PM

Quote:

Originally Posted by Gregor12

Gotcha. Well I have no idea haha I just bought the exhaust because I liked it and I know they do very good work. Oh yea. And I hit 300whp for 700 bucks and lost some weight. So it's awesome in my opinion

Sent from my iPad using Tapatalk HD

SOHO is a good shop, I've been there a couple of times. $700 sounds reasonable to me, but I couldn't go single exhaust when dual is stock. However, their final product does look much better than the prototypes.

SS_Firehawk · 08-29-2014, 09:06 PM

$700 isn't a terrible price. The gains aren't bad considering the stock Y pipe is like drinking out of a coffee straw. I love the sound of single exits, but it takes a hit on aesthetics compared to a dual. I still think it's helps having another player to choose from

08-29-2014, 02:09 PM	#1 (permalink)
aszyd Track Member Join Date: May 2014 Location: Florida Posts: 877 Drives: Magma Red 370z T+S Rep Power: 21	Very nice! Combine that with an aftermarket Y pipe and it will be a true catback. Perhaps they should consider optioning in an additional resonator on the long center pipe. __________________ Competition Clutch\|Fast Intentions\|Maxbore\|NST\|Setrab\|Stillen\|Tomei\|Uprev\| Z1 Avant Garde\|SPC\|Stance\|Whiteline Aerojacket\|Seibon\|Tanabe\|TRS\|TWM

08-29-2014, 04:30 PM	#3 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	Y PIPE BACK SINGLE MUFFLER FOR $700? My Berk full cat-back only cost me $900 and is basically double what you are buying here. If it were single 4" maybe i could see that but 3" pipe flows less than dual 2.5 there website says they picked up 8 whole horsepower with an exhaust AND tune. 2011 Nismo#91 likes this. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

08-29-2014, 05:16 PM	#9 (permalink)
Gregor12 Enthusiast Member Join Date: Oct 2013 Location: CHARLOTTE, NC Posts: 433 Drives: 2012 370z 6mt sport Rep Power: 12	i didn't dyno mine stock. didnt get around to it but considering all 370z's put down 270-280 on a dyno jet stock i'm guessing it was around there! Last edited by Gregor12; 08-29-2014 at 05:22 PM.

08-29-2014, 06:47 PM	#10 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	Hey it's all opinion if it gets your rocks off go for it, but you paid too much. Here are what his cost should be on this Vibrant 1062 - $98, 5 ft of 3" 304 $110 with bends (or ~$60 if he gets them mandrel bent), T-bolt clamp $3, hardware $1, Flange $12, Gasket $3.25, and $30-50 overhead to pay someone to make 5 welds. So 250-270 and if goes with mandrel bending it will save roughly $100 a pipe. I could have this made with a beter muffler and tip, a vband instead of a coupler clamp, and get it polished for $250. Also an X pipe doesn't reduce the CSA of twin 2.5" tubing just as an FYI the pipes cross each other there is no choke it actually increases overall flow due to harmonics. I would not call that a finished version by a long shot if he made it better by putting a bit more work into the quality of it i would have no complaints but hey someone will pay for it. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

08-29-2014, 09:06 PM	#15 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	$700 isn't a terrible price. The gains aren't bad considering the stock Y pipe is like drinking out of a coffee straw. I love the sound of single exits, but it takes a hit on aesthetics compared to a dual. I still think it's helps having another player to choose from __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

08-29-2014, 05:12 PM	#8 (permalink)
Japanjay Track Member Join Date: Mar 2012 Location: Puyallup Posts: 856 Drives: 09 Nissan 370z MB M6 Rep Power: 15	What was your stock whp number?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
3inch single exit exhaust too big for N/A	blacknismoZ	Intake/Exhaust	63	01-27-2016 01:16 PM
New Custom Exhaust Single Exit 3.5''	Megan370z	Intake/Exhaust	28	09-30-2013 08:05 PM
370z Nismo Single exit	1SlowNizzy	Member's 370Z Gallery	30	08-22-2013 03:18 AM
AMUSE R1000 single exit exhaust review	VancouverZ34	Canada	33	03-02-2012 12:44 AM
Single Exit Exhaust	JDW1479	Intake/Exhaust	4	10-26-2010 12:22 AM