PPE Long Tube Headers installed

Agent K · 06-07-2014, 09:09 PM

Well, I couldn't wait for my FI exhaust to arrive so I installed my PPE LTHs. The headers were delivered in good shape and excellent packaging. They're ceramic coated with powder black. I knew going in that these were a tough install per forum members...they were not wrong. Let me clarify, the passenger side is fairly easy to install, the driver side is a MAJOR PITA. I'm fortunate the Z isn't my daily driver.

The Start:
I put the Z on jack stands in my garage on a Saturday. I began by taking off the cross brace, engine cover, air boxes, etc. to see the stock headers. My cuz showed up and we started unbolting the heat shields...yeah we broke off a few of those flimsy bolts. We then unbolted the stock headers. And dropped them out with some heat shields still attached. We thought this was the hard part getting the stock headers out...WRONG!!!

We wanted to put the driver side PPE LTH knowing it would be the toughest. For those of you that want to install these headers without taking the motor out, you'll have to take all the driver side studs out before installing the PPE; you'll also have to disconnect the steering knuckle and tilt the motor as far as it can go. And that's the easy part. Anyway, it took us two days to get the driver side headers in place. We then put the studs back in. My cuz was spent after we set the driver side header so I finished the rest of the install by myself. Well not exactly, I had my youngest daughter give me a hand setting the passenger side header. I was actually able to torque the studs on the passenger side before I set the headers...everything else was tighten-the-s**t out of it torque. There was just not enough room to fit my torque wrench.

The End:
I finished the install on Friday night. I took the Z down off the jack stands and fired her up with fingers crossed because I had cross-threaded the bottom rear bolt hole on the driver side. So the flange nut isn't exactly flush on the header. Anyway, I fired up the Z. It started right up. A little burn off but no leaks at least not after 100 miles. No SES light and everything else works like before.

Conclusion:
I would not recommend doing this job if the Z is your daily driver, you lack time/patience, you have limited tools/skills. You're better off paying a shop to install them, and if they have any sense, they'll pull the motor. Mind you, the majority of my time was spent installing the driver side headers...around 16+ hours. The driver side took approximately 2 hours. I did the rest a little bit at a time during the week.

PPE Review:
Well there's the hiss and of course the rich exhaust smell. It brought back memories of the aftermarket exhaust I had on my Audi. The hiss is really no big deal because it is so fleeting; it's something you'll get used to. The car feels a little faster in the mid-range per butt dyno but I haven't really pushed it yet. Right now, I get what sounds like a backfire but I think this is due to the restriction of the stock exhaust; I suspect most if not all of this will go away after I install the FI exhaust. It happens on downshifts and not every gear and not all the time; it's really only occasionally. Again, I think most, if not all this will go away with the FI exhaust.

Eclipz · 06-08-2014, 12:34 PM

Holy cow. 16 hours. You must have felt like a champ after you finished the install. Post a video when you get the FI exhaust

Sent from my SGH-T999L using Tapatalk

BOLIO 671 · 06-08-2014, 12:52 PM

After going through all that on this install, the install of ur FI exhaust when it arrives will be a breeze/walk in the park....Lol

Agent K · 06-08-2014, 02:24 PM

Quote:

Originally Posted by Eclipz

Holy cow. 16 hours. You must have felt like a champ after you finished the install. Post a video when you get the FI exhaust

Sent from my SGH-T999L using Tapatalk

Oh, did I fail to mention that we had to take the driver side PPE headers back out in order to tap the engine block holes. And obviously I didn't do a good job because one of studs didn't go in straight. Also, that 16+ hours included breaks and trips to the hardware store.

Megan370z · 06-08-2014, 04:13 PM

Quote:

Originally Posted by Agent K

Well, I couldn't wait for my FI exhaust to arrive so I installed my PPE LTHs. The headers were delivered in good shape and excellent packaging. They're ceramic coated with powder black. I knew going in that these were a tough install per forum members...they were not wrong. Let me clarify, the passenger side is fairly easy to install, the driver side is a MAJOR PITA. I'm fortunate the Z isn't my daily driver.

The Start:
I put the Z on jack stands in my garage on a Saturday. I began by taking off the cross brace, engine cover, air boxes, etc. to see the stock headers. My cuz showed up and we started unbolting the heat shields...yeah we broke off a few of those flimsy bolts. We then unbolted the stock headers. And dropped them out with some heat shields still attached. We thought this was the hard part getting the stock headers out...WRONG!!!

We wanted to put the driver side PPE LTH knowing it would be the toughest. For those of you that want to install these headers without taking the motor out, you'll have to take all the driver side studs out before installing the PPE; you'll also have to disconnect the steering knuckle and tilt the motor as far as it can go. And that's the easy part. Anyway, it took us two days to get the driver side headers in place. We then put the studs back in. My cuz was spent after we set the driver side header so I finished the rest of the install by myself. Well not exactly, I had my youngest daughter give me a hand setting the passenger side header. I was actually able to torque the studs on the passenger side before I set the headers...everything else was tighten-the-s**t out of it torque. There was just not enough room to fit my torque wrench.

The End:
I finished the install on Friday night. I took the Z down off the jack stands and fired her up with fingers crossed because I had cross-threaded the bottom rear bolt hole on the driver side. So the flange nut isn't exactly flush on the header. Anyway, I fired up the Z. It started right up. A little burn off but no leaks at least not after 100 miles. No SES light and everything else works like before.

Conclusion:
I would not recommend doing this job if the Z is your daily driver, you lack time/patience, you have limited tools/skills. You're better off paying a shop to install them, and if they have any sense, they'll pull the motor. Mind you, the majority of my time was spent installing the driver side headers...around 16+ hours. The driver side took approximately 2 hours. I did the rest a little bit at a time during the week.

PPE Review:
Well there's the hiss and of course the rich exhaust smell. It brought back memories of the aftermarket exhaust I had on my Audi. The hiss is really no big deal because it is so fleeting; it's something you'll get used to. The car feels a little faster in the mid-range per butt dyno but I haven't really pushed it yet. Right now, I get what sounds like a backfire but I think this is due to the restriction of the stock exhaust; I suspect most if not all of this will go away after I install the FI exhaust. It happens on downshifts and not every gear and not all the time; it's really only occasionally. Again, I think most, if not all this will go away with the FI exhaust.

Quote:

Originally Posted by Agent K

Oh, did I fail to mention that we had to take the driver side PPE headers back out in order to tap the engine block holes. And obviously I didn't do a good job because one of studs didn't go in straight. Also, that 16+ hours included breaks and trips to the hardware store.

not too bad on your first time with the 370z..
I had the same issue on my first ever install with a cross threaded stud !
Then a rounded nut that took a few days to deal with ( jacked in a parking lot).

the steering knuckle has to be removed anyways and using shorter studs/nuts made this process quite a bit faster after ! 90mins for the whole process.

synolimit · 06-08-2014, 04:36 PM

Quote:

Originally Posted by Megan370z

not too bad on your first time with the 370z..
I had the same issue on my first ever install with a cross threaded stud !
Then a rounded nut that took a few days to deal with ( jacked in a parking lot).

the steering knuckle has to be removed anyways and using shorter studs/nuts made this process quite a bit faster after ! 90mins for the whole process.

Really? I left my steering knuckle. Just lifted the motor some and done.

Megan370z · 06-08-2014, 06:30 PM

Quote:

Originally Posted by synolimit

Really? I left my steering knuckle. Just lifted the motor some and done.

ok

Rusty · 06-08-2014, 07:24 PM

My hardest problem was the damn heat shield on the drivers side. Trying to take it out in one piece. Left side - 45 minutes. Right side - 5 hrs.

synolimit · 06-08-2014, 08:52 PM

Quote:

Originally Posted by Rusty

My hardest problem was the damn heat shield on the drivers side. Trying to take it out in one piece. Left side - 45 minutes. Right side - 5 hrs.

Ditto.

Maybe the design matters. Ppe have a odd shape.

Rusty · 06-08-2014, 11:53 PM

Quote:

Originally Posted by Rusty

My hardest problem was the damn heat shield on the drivers side. Trying to take it out in one piece. Left side - 45 minutes. Right side - 5 hrs.

Quote:

Originally Posted by synolimit

Ditto.

Maybe the design matters. Ppe have a odd shape.

Spent most of my time on the heat shield. Once I got that out. It only took me about 1.5 hrs on removing and installing the left side.

Agent K · 06-09-2014, 04:42 AM

Let's be clear, PPE headers are designed differently from stock and FI LTH. I managed to get the stock headers out without disconnecting the steering knuckle or tilting the motor. Other than removing the motor, there is no way to install PPE headers without disconnecting the steering knuckle and tilting the motor.IMAG0271_BURST002.jpg

Megan370z · 06-09-2014, 06:38 AM

Quote:

Originally Posted by Agent K

Let's be clear, PPE headers are designed differently from stock and FI LTH. I managed to get the stock headers out without disconnecting the steering knuckle or tilting the motor. Other than removing the motor, there is no way to install PPE headers without disconnecting the steering knuckle and tilting the motor.Attachment 89771

Let's be clear too

I never tried to tilt the engine while installing the PPE so many times now. because I installed shorter stud. but yeah like I said the steering knuckle has to be removed if you install the PPE .

synolimit has done it with only tilting the engine without removing he steering knuckle as he said.

Agent K · 06-09-2014, 07:21 AM

Megan370,

Where did you get shorter studs? Did they have the star ends? Did you replace all or some?

Megan370z · 06-09-2014, 12:26 PM

Quote:

Originally Posted by Agent K

Megan370,

Where did you get shorter studs? Did they have the star ends? Did you replace all or some?

I went to a specialized shop and found something to replace the long factory stud . I replaced all of them to make it easier on future install/removal which helped a lot when I did my custom exhaust.

Agent K · 06-09-2014, 12:55 PM

Quote:

Originally Posted by Megan370z

I went to a specialized shop and found something to replace the long factory stud . I replaced all of them to make it easier on future install/removal which helped a lot when I did my custom exhaust.

Now that's forward thinking

I replaced the bottom rear driver side stud with a shorter one that I got from the dealership ; of course , it doesn't have the star end. It is about a 1/4" shorter. It was the last one they had in stock; so far it's holding.

06-07-2014, 09:09 PM	#1 (permalink)
Agent K Base Member Join Date: Jul 2013 Location: Memphis, TN Posts: 155 Drives: '13 370Z MBlue 6MT Rep Power: 12	PPE Long Tube Headers installed Well, I couldn't wait for my FI exhaust to arrive so I installed my PPE LTHs. The headers were delivered in good shape and excellent packaging. They're ceramic coated with powder black. I knew going in that these were a tough install per forum members...they were not wrong. Let me clarify, the passenger side is fairly easy to install, the driver side is a MAJOR PITA. I'm fortunate the Z isn't my daily driver. The Start: I put the Z on jack stands in my garage on a Saturday. I began by taking off the cross brace, engine cover, air boxes, etc. to see the stock headers. My cuz showed up and we started unbolting the heat shields...yeah we broke off a few of those flimsy bolts. We then unbolted the stock headers. And dropped them out with some heat shields still attached. We thought this was the hard part getting the stock headers out...WRONG!!! We wanted to put the driver side PPE LTH knowing it would be the toughest. For those of you that want to install these headers without taking the motor out, you'll have to take all the driver side studs out before installing the PPE; you'll also have to disconnect the steering knuckle and tilt the motor as far as it can go. And that's the easy part. Anyway, it took us two days to get the driver side headers in place. We then put the studs back in. My cuz was spent after we set the driver side header so I finished the rest of the install by myself. Well not exactly, I had my youngest daughter give me a hand setting the passenger side header. I was actually able to torque the studs on the passenger side before I set the headers...everything else was tighten-the-st out of it torque. There was just not enough room to fit my torque wrench. The End: I finished the install on Friday night. I took the Z down off the jack stands and fired her up with fingers crossed because I had cross-threaded the bottom rear bolt hole on the driver side. So the flange nut isn't exactly flush on the header. Anyway, I fired up the Z. It started right up. A little burn off but no leaks** at least not after 100 miles. No SES light and everything else works like before. Conclusion: I would not recommend doing this job if the Z is your daily driver, you lack time/patience, you have limited tools/skills. You're better off paying a shop to install them, and if they have any sense, they'll pull the motor. Mind you, the majority of my time was spent installing the driver side headers...around 16+ hours. The driver side took approximately 2 hours. I did the rest a little bit at a time during the week. PPE Review: Well there's the hiss and of course the rich exhaust smell. It brought back memories of the aftermarket exhaust I had on my Audi. The hiss is really no big deal because it is so fleeting; it's something you'll get used to. The car feels a little faster in the mid-range per butt dyno but I haven't really pushed it yet. Right now, I get what sounds like a backfire but I think this is due to the restriction of the stock exhaust; I suspect most if not all of this will go away after I install the FI exhaust. It happens on downshifts and not every gear and not all the time; it's really only occasionally. Again, I think most, if not all this will go away with the FI exhaust. SS_Firehawk likes this.

06-08-2014, 12:52 PM	#3 (permalink)
BOLIO 671 A True Z Fanatic Join Date: Mar 2010 Location: GUAHAN Posts: 1,198 Drives: To & From then Back Rep Power: 3399	After going through all that on this install, the install of ur FI exhaust when it arrives will be a breeze/walk in the park....Lol __________________ 2013 Nismo Z34 / FI TT #091 / IG: @lilzilla_z34

06-08-2014, 07:24 PM	#8 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,180 Drives: 2011 Nismo GM 6M Rep Power: 2684437	My hardest problem was the damn heat shield on the drivers side. Trying to take it out in one piece. Left side - 45 minutes. Right side - 5 hrs. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PPE Long Tube Headers Installed...	chuckd05	Intake/Exhaust	61	10-03-2015 08:24 PM
[WTB] FI long tube headers	fryzia23	Parts for sale (Private Classifieds)	0	04-17-2013 01:51 PM
[WTB] Long tube headers	DEpointfive0	Parts for sale (Private Classifieds)	1	03-07-2012 12:47 PM
F.I. Long-Tube Headers installed - Review/Pics/Vids/Dyno	semtex	Intake/Exhaust	137	06-01-2010 01:15 PM
FI Long Tube Headers	docaam	Parts for sale (Private Classifieds)	9	03-31-2010 02:01 PM

06-08-2014, 12:34 PM	#2 (permalink)
Eclipz Enthusiast Member Join Date: Dec 2013 Location: Tampa Posts: 360 Drives: 06 Eclipse GS Rep Power: 11	Holy cow. 16 hours. You must have felt like a champ after you finished the install. Post a video when you get the FI exhaust Sent from my SGH-T999L using Tapatalk

06-09-2014, 04:42 AM	#11 (permalink)
Agent K Base Member Join Date: Jul 2013 Location: Memphis, TN Posts: 155 Drives: '13 370Z MBlue 6MT Rep Power: 12	Let's be clear, PPE headers are designed differently from stock and FI LTH. I managed to get the stock headers out without disconnecting the steering knuckle or tilting the motor. Other than removing the motor, there is no way to install PPE headers without disconnecting the steering knuckle and tilting the motor.IMAG0271_BURST002.jpg

06-09-2014, 07:21 AM	#13 (permalink)
Agent K Base Member Join Date: Jul 2013 Location: Memphis, TN Posts: 155 Drives: '13 370Z MBlue 6MT Rep Power: 12	Megan370, Where did you get shorter studs? Did they have the star ends? Did you replace all or some?