Custom ported and CNC throttle bodies, upper and lower manifolds by Synergy Composite

N0SL3N · 05-09-2014, 04:02 PM

Whats the ID on the throttle bodies?

synolimit · 05-09-2014, 04:04 PM

Idk I'll check. Whats OEM? Tb's are my first issue.

Bananaz · 05-09-2014, 04:05 PM

So what re you upset about?

Sent from my SCH-I545 using Tapatalk

N0SL3N · 05-09-2014, 04:14 PM

I think 67.5 mm. Megan knows for sure.

synolimit · 05-09-2014, 04:15 PM

Quote:

Originally Posted by N0SL3N

Whats the ID on the throttle bodies?

2.6 ish on the front lip. 2.5 in the middle and as far as my calipers can get. 2.39 on the back lip and that's not even port matched to the manifold since that's 2.5". And as far as I can get in on the backside its 2.35".

So 2.6 to 2.5 to butterfly at probably 2.35, then 2.35 out to 2.39. These need ******* machined.

synolimit · 05-09-2014, 04:21 PM

Quote:

Originally Posted by Bananaz

So what re you upset about?

Sent from my SCH-I545 using Tapatalk

I'll PM

N0SL3N · 05-09-2014, 04:32 PM

Yeah, the throttle body isn't exactly what I thought. I thought they would remove the butterfly and open up straight through but it looks just highly polished.

Might consider trying maxbore and see how that works out.

synolimit · 05-09-2014, 04:37 PM

Quote:

Originally Posted by N0SL3N

Yeah, the throttle body isn't exactly what I thought. I thought they would remove the butterfly and open up straight through but it looks just highly polished.

Might consider trying maxbore and see how that works out.

I knew and said that wouldn't happen. Opening and CNC would of tripled the price. Plus new butterfly plate cost. I was under the impression all would be opened as far as possible but the 1/8th the plate touches so no idle issues. The fact the rear isn't port matched to the mani ticks me off. The back and the mani can go way beyond 2.5".

Megan370z · 05-09-2014, 06:11 PM

Quote:

Originally Posted by N0SL3N

I think 67.5 mm. Megan knows for sure.

the OEM TB are 60mm
mine were bored to 62.5mm

62.5mm to inch = 2.46063''

on the posted picture with those shiny polished TB ,, I doubt there was any boring at all since there is still that OEM bump at the butterfly plate

then next ... I hope those 2 screw holding the plate are atleast torqued down with some Red Loctite !!
stacking them is always a safe bet for this stuff !!

the reason why I'm saying this is because the plate is now thinner and not much thread holding those screws...

the work on the lower intake manifold look quite good on those picture

He seem to also have done alright with the matching of both lower & upper manifold ,, could have been better since I think the lower corner were done a bit fast...

370Z JT · 05-09-2014, 07:05 PM

When are you gonna get dyno numbers?

Super Werty · 05-09-2014, 07:17 PM

I hate to be so pessimistic but I bet its around 5 rwhp, which honestly could be a change in weather conditions

prove me wrong though!

Megan370z · 05-09-2014, 08:01 PM

Quote:

Originally Posted by Super Werty

I hate to be so pessimistic but I bet its around 5 rwhp, which honestly could be a change in weather conditions

prove me wrong though!

It should be about that 3-5whp from the intake manifold work. Because in stock form, the fitting between the 2 of them (lower and upper) isnt great !!! If you seen the pictures that was provided before. You should know..

Juan@Fontana · 05-09-2014, 08:14 PM

I think the manifold work looks OK, could be better though. The throttle body work though looks like just a polishing job and no actual porting.

-Juan

synolimit · 05-09-2014, 09:36 PM

Quote:

Originally Posted by Megan370z

on the posted picture with those shiny polished TB ,, I doubt there was any boring at all since there is still that OEM bump at the butterfly plate

Well we left it so not to mess with the idle. I wanted everything bigger but that 1/8th lip. But looks like nothing was done. Maxbore for $179 seems to CNC the whole thing plus a bigger butterfly. Looks like ill head that route as I know the plate is only 2.35 inch and the intake and manifold are 2.5". Makes no sense to bottle neck it.

Quote:

Originally Posted by Megan370z

then next ... I hope those 2 screw holding the plate are atleast torqued down with some Red Loctite !!
stacking them is always a safe bet for this stuff !!

the reason why I'm saying this is because the plate is now thinner and not much thread holding those screws...

They were never removed. The threads of the screws stuck into the path of air flow so they were just ground flush with the rod. No material looks to be removed on the rod.

Quote:

Originally Posted by Megan370z

the work on the lower intake manifold look quite good on those picture

He seem to also have done alright with the matching of both lower & upper manifold ,, could have been better since I think the lower corner were done a bit fast...

The issue is the manifold has wiggle room. Push it right and you get a over lapping, push left and the port matching is perfect. When installed you'll have remember which way to push so it perfectly smooth.

synolimit · 05-09-2014, 09:42 PM

Quote:

Originally Posted by 370Z JT

When are you gonna get dyno numbers?

Not sure now. I want more material removed on the upper and lower and the TB's definently need CNC with a bigger plate. Calling Maxbore Monday. I might still proceed forward, try and use these tb's, then sell them after my OEM are maxbored out. I'll call tuner Monday too to see whats up.

05-09-2014, 04:02 PM	#121 (permalink)
N0SL3N Enthusiast Member Join Date: Dec 2011 Location: Toronto Posts: 376 Drives: 2009 PG 370z 6MT Rep Power: 34	Whats the ID on the throttle bodies? __________________ \| Akuma \| Motordyne \| Z1 \| NST \| CNT \| Stillen \| Avant Garde \| RJM \| Performix \| Tint \| LED \| GTR \| Nissan \|

05-09-2014, 04:04 PM	#122 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3389	Idk I'll check. Whats OEM? Tb's are my first issue. __________________ 13 370z-

05-09-2014, 04:05 PM	#123 (permalink)
Bananaz Track Member Join Date: Dec 2013 Location: Central Jersey Posts: 637 Drives: 09 370z 6MT/B+Sport Rep Power: 13	So what re you upset about? Sent from my SCH-I545 using Tapatalk __________________ BC - SSR - Evo-R - ViS - SPC - ZSpeed - Beluga - Blox - 35% Tint - Clutch Spring - Fang Forced Air Ducting

05-09-2014, 04:14 PM	#124 (permalink)
N0SL3N Enthusiast Member Join Date: Dec 2011 Location: Toronto Posts: 376 Drives: 2009 PG 370z 6MT Rep Power: 34	I think 67.5 mm. Megan knows for sure. __________________ \| Akuma \| Motordyne \| Z1 \| NST \| CNT \| Stillen \| Avant Garde \| RJM \| Performix \| Tint \| LED \| GTR \| Nissan \|

05-09-2014, 04:32 PM	#127 (permalink)
N0SL3N Enthusiast Member Join Date: Dec 2011 Location: Toronto Posts: 376 Drives: 2009 PG 370z 6MT Rep Power: 34	Yeah, the throttle body isn't exactly what I thought. I thought they would remove the butterfly and open up straight through but it looks just highly polished. Might consider trying maxbore and see how that works out. __________________ \| Akuma \| Motordyne \| Z1 \| NST \| CNT \| Stillen \| Avant Garde \| RJM \| Performix \| Tint \| LED \| GTR \| Nissan \|

05-09-2014, 07:05 PM	#130 (permalink)
370Z JT A True Z Fanatic Join Date: Jan 2010 Location: United States Posts: 2,905 Drives: 370Z PW 7AT Rep Power: 378	When are you gonna get dyno numbers? __________________ Click for My Journal Top Secret \| EVO-R \| Fujimura Auto \| Shine Auto \| Seibon \| MRWorks \| Swift \| SPC \| SSR \| UpRev \| Project Kics \| NST \| Titek \| Eibach \| Nismo \| Whiteline \| Quaife \| Invidia \| Fly1 \| CF Element \| Carbon Signal

05-09-2014, 07:17 PM	#131 (permalink)
Super Werty Track Member Join Date: Jul 2013 Location: AZ Posts: 668 Drives: '13 Sport Rep Power: 13	I hate to be so pessimistic but I bet its around 5 rwhp, which honestly could be a change in weather conditions prove me wrong though! __________________ The Build Last edited by Super Werty; 05-09-2014 at 07:24 PM.

05-09-2014, 08:14 PM	#133 (permalink)
Juan@Fontana Enthusiast Member Join Date: Nov 2013 Location: Fontana Posts: 315 Drives: Z32 Rep Power: 21	I think the manifold work looks OK, could be better though. The throttle body work though looks like just a polishing job and no actual porting. -Juan

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom ported and CNC throttle bodies, upper and lower manifolds	synolimit	Exhaust/Intake	297	06-25-2021 10:13 AM
[WTB] Lower intake manifolds! Uppers and TB's welcome!!	synolimit	Parts for sale (Private Classifieds)	0	11-19-2014 03:02 AM
Smokeys dyno, ported TB's, manifolds etc	synolimit	Tuning	8	08-15-2014 12:11 PM
can the throttle bodies be taken off?	boomboom	Engine & Drivetrain	9	11-03-2013 02:46 PM
Kinetix 370Z/G37 Velocity Upper Intake Manifolds - Z1 Motorsports	Dustin@Z1	Intake/Exhaust	151	03-18-2013 10:37 AM