Stillen Gen 2 intake

JvKintheUSA · 08-13-2009, 03:51 PM

Okay, so I am trying the Stillen Gen 2 intake, so I do not have to deal with removing the bumper. I installed the intake, and it wasn't easy. First of all, the relay box on the drivers side needs to be moved, but where to? Instructions seem to be for the G35. There is absolutely no place to move to relay box to. So right now, it is laying on top of the intake box, probably rubbing the hood. Not good. Secondly, the passenger side filter is rubbing against the power steering fluid container. Not good. Seems that Stillen is selling the G35 intake for the 370Z. Just bad fit and finish Stillen. Now I have to see if I can pull the passenger side intake closer to the engine with some metal straps, which will cause the intake box to rub against the cooling system rubber hose - not good. What a pain. Stillen, if you are reading this, any suggestions? I hate to take the system out and cut the intake boxes to the right size. $450 should give me a better product, and not a "G35-kinda fit in a 370Z" intake system.

LiquidZ · 08-13-2009, 03:58 PM

Quote:

Originally Posted by JvKintheUSA

Okay, so I am trying the Stillen Gen 2 intake, so I do not have to deal with removing the bumper. I installed the intake, and it wasn't easy. First of all, the relay box on the drivers side needs to be moved, but where to? Instructions seem to be for the G35. There is absolutely no place to move to relay box to. So right now, it is laying on top of the intake box, probably rubbing the hood. Not good. Secondly, the passenger side filter is rubbing against the power steering fluid container. Not good. Seems that Stillen is selling the G35 intake for the 370Z. Just bad fit and finish Stillen. Now I have to see if I can pull the passenger side intake closer to the engine with some metal straps, which will cause the intake box to rub against the cooling system rubber hose - not good. What a pain. Stillen, if you are reading this, any suggestions? I hate to take the system out and cut the intake boxes to the right size. $450 should give me a better product, and not at "G35-kinda fit in a 370Z" intake system.

I recommend you sending a PM to Stillen or calling them directly. They are known to have excellent customer support and can help you with anything.

I'm not sure if they designed a G2 unit for the 370Z? If they did, they might have sent the wrong unit?

JvKintheUSA · 08-13-2009, 07:23 PM

Quote:

Originally Posted by LiquidZ

I recommend you sending a PM to Stillen or calling them directly. They are known to have excellent customer support and can help you with anything.

I'm not sure if they designed a G2 unit for the 370Z? If they did, they might have sent the wrong unit?

thanks! I called and left a message - no reply yet. I cut and modified the intake box a little and used a hose clamp to pull it closer to the engine and now it does not rub against anything on the passenger side. Still no good solution for the relay box on the drivers side. This intake will have to do for now until I find something better - maybe the r2c when it comes out.

Solus · 08-14-2009, 09:58 AM

Try pm'ing Josh@Stillen on here. He is always pretty helpful

Reality · 08-14-2009, 10:45 AM

Quote:

Originally Posted by LiquidZ

I recommend you sending a PM to Stillen or calling them directly. They are known to have excellent customer support and can help you with anything.

I'm not sure if they designed a G2 unit for the 370Z? If they did, they might have sent the wrong unit?

GMZ · 08-14-2009, 10:55 AM

Quote:

Originally Posted by Solus

Try pm'ing Josh@Stillen on here. He is always pretty helpful

He helped me out really quickly with some GIII questions I had.

Quote:

Originally Posted by Reality

Whats so funny? The guys from Stillen on the board are a pretty nifty resource.

LiquidZ · 08-14-2009, 12:59 PM

Quote:

Originally Posted by Reality

Maybe you have had different experiences from what I have seen on this board.

JvKintheUSA · 08-15-2009, 10:05 AM

Well, I tried to finagle the Gen 2 intake, but I am taking it out and put the stock back in. I'm OCD when it comes to fit, especially in the engine bay. No rubbing anything! If anyone is willing to buy it off me, I'm selling it 1/2 off the original, $210 + shipping. Still have the box, instructions and all components. Send me a PM if interested and we will work out the details.

LiquidZ · 08-15-2009, 11:57 AM

Quote:

Originally Posted by JvKintheUSA

Well, I tried to finagle the Gen 2 intake, but I am taking it out and put the stock back in. I'm OCD when it comes to fit, especially in the engine bay. No rubbing anything! If anyone is willing to buy it off me, I'm selling it 1/2 off the original, $210 + shipping. Still have the box, instructions and all components. Send me a PM if interested and we will work out the details.

Did they not get back to you?

kdo2milger · 08-15-2009, 12:22 PM

i would definately send it back...worse case scenario you only loose return shipping fees, rather than trying to sell it for half price...

JvKintheUSA · 08-15-2009, 06:25 PM

Quote:

Originally Posted by kdo2milger

i would definately send it back...worse case scenario you only loose return shipping fees, rather than trying to sell it for half price...

I scratched the intake tube on the passenger side trying to pull it closer to the engine. Not sure they will take it back. I spoke today with Kenny @ Stillen, and discussed the relay box issue. Seems that there truly is no good place to place it with the Gen 2 intake. It just has to sit on top of the drivers side intake box, kinda tucked in the corner, not as the instructions show velcroed under the intake cover.

cre8iveDH · 09-25-2009, 07:19 PM

Quote:

Originally Posted by JvKintheUSA

I scratched the intake tube on the passenger side trying to pull it closer to the engine. Not sure they will take it back. I spoke today with Kenny @ Stillen, and discussed the relay box issue. Seems that there truly is no good place to place it with the Gen 2 intake. It just has to sit on top of the drivers side intake box, kinda tucked in the corner, not as the instructions show velcroed under the intake cover.

I also just bought the Gen2 Stillen Intake. I installed it yesterday. Have had no problems with the passenger side tube, however, right now the relay box is sitting below the intake box/resting on top of the wheel well. Trying to figure out if there is a way to bend the original bracket that it is attached to in order to tuck it in a little further.

spearfish25 · 09-25-2009, 07:30 PM

Unless they specifically told you that you'd have this installation issue, I'd send it back and request a refund. You can always dispute charges with your credit card company as well. I'd be furious if I ordered a product that was supposed to be an easy install and then had your problems described here. All of this goes out the window though if Stillen warned you about this first though.

Zsteve · 09-25-2009, 11:11 PM

So does the R2c have the same issues with the relay box?

JvKintheUSA · 09-25-2009, 11:51 PM

Quote:

Originally Posted by Zsteve

So does the R2c have the same issues with the relay box?

None! The R2C fits perfectly and the relay box does not need to be moved.

Check out my video:

08-13-2009, 03:51 PM	#1 (permalink)
JvKintheUSA Enthusiast Member Join Date: Jun 2009 Location: Canton, GA Posts: 465 Drives: 2013 Shelby GT500 Rep Power: 428	Stillen Gen 2 intake Okay, so I am trying the Stillen Gen 2 intake, so I do not have to deal with removing the bumper. I installed the intake, and it wasn't easy. First of all, the relay box on the drivers side needs to be moved, but where to? Instructions seem to be for the G35. There is absolutely no place to move to relay box to. So right now, it is laying on top of the intake box, probably rubbing the hood. Not good. Secondly, the passenger side filter is rubbing against the power steering fluid container. Not good. Seems that Stillen is selling the G35 intake for the 370Z. Just bad fit and finish Stillen. Now I have to see if I can pull the passenger side intake closer to the engine with some metal straps, which will cause the intake box to rub against the cooling system rubber hose - not good. What a pain. Stillen, if you are reading this, any suggestions? I hate to take the system out and cut the intake boxes to the right size. $450 should give me a better product, and not a "G35-kinda fit in a 370Z" intake system. __________________ Last edited by JvKintheUSA; 08-13-2009 at 09:20 PM.

08-15-2009, 10:05 AM	#8 (permalink)
JvKintheUSA Enthusiast Member Join Date: Jun 2009 Location: Canton, GA Posts: 465 Drives: 2013 Shelby GT500 Rep Power: 428	Well, I tried to finagle the Gen 2 intake, but I am taking it out and put the stock back in. I'm OCD when it comes to fit, especially in the engine bay. No rubbing anything! If anyone is willing to buy it off me, I'm selling it 1/2 off the original, $210 + shipping. Still have the box, instructions and all components. Send me a PM if interested and we will work out the details. __________________

08-15-2009, 12:22 PM	#10 (permalink)
kdo2milger OG Priesthood Join Date: Feb 2009 Location: Fargo, ND Posts: 17,859 Drives: NISMO T Rep Power: 59	i would definately send it back...worse case scenario you only loose return shipping fees, rather than trying to sell it for half price... __________________ Project *NISMO*

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust	axio	Intake/Exhaust	82	07-31-2009 01:41 PM
Stillen g3 intake	NewlyIMPORTed	Intake/Exhaust	39	06-26-2009 08:22 PM
Berk HFC's, Stillen Intake, and a Stillen Dual Exhaust....	2theextreme	The Lounge (Off Topic)	8	06-18-2009 11:01 PM
Berk HFC and stillen Gen 3 intake	JonnieN	Intake/Exhaust	5	06-01-2009 03:26 PM
For sale Stillen G3 Intake	jpit	Parts for sale (Private Classifieds)	10	05-30-2009 10:31 AM

08-14-2009, 09:58 AM	#4 (permalink)
Solus Enthusiast Member Join Date: Apr 2009 Location: Jacksonville, NC Posts: 453 Drives: 2009 Nissan 370z Rep Power: 16	Try pm'ing Josh@Stillen on here. He is always pretty helpful

09-25-2009, 07:30 PM	#13 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1856	Unless they specifically told you that you'd have this installation issue, I'd send it back and request a refund. You can always dispute charges with your credit card company as well. I'd be furious if I ordered a product that was supposed to be an easy install and then had your problems described here. All of this goes out the window though if Stillen warned you about this first though.

09-25-2009, 11:11 PM	#14 (permalink)
Zsteve A True Z Fanatic Join Date: Sep 2009 Location: TX Posts: 3,298 Drives: the 2 balled club Rep Power: 22	So does the R2c have the same issues with the relay box?