Installing Momentum Headers

chrischhorn · 02-23-2013, 01:33 AM

Quote:

Originally Posted by AlexRaymond19

P0420 p0430. Too much steel wool is my guess. I packed that sucker good

Not enough I think. I just have a 1.5" extender and I'm throwing the same codes. Time to pack tighter!

AlexRaymond19 · 02-23-2013, 02:31 AM

Good to know! I have the extenders from z1 on my z1 tp's. But they are like 3 inches long i think, so maybe its different. The hole in the bottom of the extender is like BB sized, and with the amount of steel wool i packed in there i think its not getting enough flow, but i could be off base. the code description does say "under performing cat" which would lead me to believe that the sensor is reading too much flow. What size steel wool is best to use? I got some medium fine grade, wondering if i should get the ultra fine grade to blow flow better. Is there a point where it will throw a code if it is not getting enough flow? If not i will just block the hole completely with a solid washer like disk and then put the sensors on.

Side note, i got my wheels re-torqued today along with and alignment and now my tpms sensors are doing the minute long flashing thing and then staying on. It did not throw an error before this. Is there anyway they could have ****** my sensors up just by tightening my lugs?

JC671 · 02-23-2013, 03:11 AM

Quote:

Originally Posted by AlexRaymond19

Good to know! I have the extenders from z1 on my z1 tp's. But they are like 3 inches long i think, so maybe its different. The hole in the bottom of the extender is like BB sized, and with the amount of steel wool i packed in there i think its not getting enough flow, but i could be off base. the code description does say "under performing cat" which would lead me to believe that the sensor is reading too much flow. What size steel wool is best to use? I got some medium fine grade, wondering if i should get the ultra fine grade to blow flow better. Is there a point where it will throw a code if it is not getting enough flow? If not i will just block the hole completely with a solid washer like disk and then put the sensors on.

Side note, i got my wheels re-torqued today along with and alignment and now my tpms sensors are doing the minute long flashing thing and then staying on. It did not throw an error before this. Is there anyway they could have ****** my sensors up just by tightening my lugs?

TPMS is strictly tire pressure man. Check your tires and make sure they are above 30-32 PSI. I forgot when it signals the TPMS to turn on.

chrischhorn · 02-23-2013, 12:35 PM

Quote:

Originally Posted by JC671

TPMS is strictly tire pressure man. Check your tires and make sure they are above 30-32 PSI. I forgot when it signals the TPMS to turn on.

If its flashing at him, he's got a sensor malfunction. Alex, did you buy new TPMS for the new wheels or did you just transfer over your original sensors? Some Nissans will need to be relearned after switching sensors or even after some simple work like rotations and rebalances. Just depends on how long the wheels were off the car for. Sometimes a quick scan of the sensors with the scan tool while they are on the vehicle will reset the sensors too. Also, our sensors don't alert us until the PSI drops below 26.

AlexRaymond19 · 02-23-2013, 04:11 PM

They worked fine for about 50 miles then Turned on after while I wss driving after the alignment. Im going to check with the place and see what they did excatly. I set the tire pressure to 35 psi and have checked it like 5 times since

AlexRaymond19 · 02-24-2013, 07:09 PM

Hey chris, or anyone with the motordyne manifold, i ran into a situation while doing the install. Does it matter which goes where as far as the MAP sensor and the vac line? I mean it plugs into the same hose. The instructions say to plug the map sensor into a solid metal end with no hose on it. It wont fit on. I think the instructions are just wrong, but i just wanted to make sure

SS_Firehawk · 02-24-2013, 08:08 PM

If I remember, It was T's off to the back of the manifold. It's been a while, I know I have a drawing sent to me from somewhere, I'll find it

AlexRaymond19 · 02-24-2013, 09:33 PM

Yeah, thats the one i am talking about. It t's off in the back of the manifold, and the instructions tell me to put the MAP sensor on the bare metal, but it needs a hose to connect to. I think it is just labeled wrong in the instructions. I started it up and it was fine, until the engine started smoking like crazy. A little bit of that blue fluid from one of the lines dripped on the header while i was taking it off... I almost freaked out, until i realized what happened. The smoke had a sweet smell almost

SS_Firehawk · 02-24-2013, 09:39 PM

yeah, I had it plugged into a hose.

chrischhorn · 02-25-2013, 03:16 AM

Alex, there are 2 hose ports on the back of the manifold. 1 is to loop around to the front for the crank case pressure lines that originally connect in front with 1 of the t's. The other 1 is to be T'd with the vac hose on the back by the firewall and the map sensor goes on the other end and plugs back into where it originally was. Mine is slightly different set up as I just wasn't paying attention but it works fine and I'm too lazy to change it lol.

AlexRaymond19 · 02-25-2013, 07:46 AM

Ah, gotcha.

AlexRaymond19 · 02-25-2013, 11:24 AM

the intake manifold has nevewr been off before. Wondering if that scratch inside is anything to worry about, or just sub par nissan craftmanshit

AlexRaymond19 · 02-25-2013, 11:25 AM

craftmanship*

Rusty · 02-25-2013, 01:17 PM

When the manifold was cast. It looks like someone took a burr bit to it to clean up that area some.

AlexRaymond19 · 02-25-2013, 02:17 PM

Ahh, has anyone ever taken that off and polished it perfectly smooth?

02-23-2013, 02:31 AM	#137 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Good to know! I have the extenders from z1 on my z1 tp's. But they are like 3 inches long i think, so maybe its different. The hole in the bottom of the extender is like BB sized, and with the amount of steel wool i packed in there i think its not getting enough flow, but i could be off base. the code description does say "under performing cat" which would lead me to believe that the sensor is reading too much flow. What size steel wool is best to use? I got some medium fine grade, wondering if i should get the ultra fine grade to blow flow better. Is there a point where it will throw a code if it is not getting enough flow? If not i will just block the hole completely with a solid washer like disk and then put the sensors on. Side note, i got my wheels re-torqued today along with and alignment and now my tpms sensors are doing the minute long flashing thing and then staying on. It did not throw an error before this. Is there anyway they could have **** my sensors up just by tightening my lugs? __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang**

02-23-2013, 04:11 PM	#140 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	They worked fine for about 50 miles then Turned on after while I wss driving after the alignment. Im going to check with the place and see what they did excatly. I set the tire pressure to 35 psi and have checked it like 5 times since __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-24-2013, 07:09 PM	#141 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Hey chris, or anyone with the motordyne manifold, i ran into a situation while doing the install. Does it matter which goes where as far as the MAP sensor and the vac line? I mean it plugs into the same hose. The instructions say to plug the map sensor into a solid metal end with no hose on it. It wont fit on. I think the instructions are just wrong, but i just wanted to make sure __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-24-2013, 08:08 PM	#142 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	If I remember, It was T's off to the back of the manifold. It's been a while, I know I have a drawing sent to me from somewhere, I'll find it __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

02-24-2013, 09:33 PM	#143 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Yeah, thats the one i am talking about. It t's off in the back of the manifold, and the instructions tell me to put the MAP sensor on the bare metal, but it needs a hose to connect to. I think it is just labeled wrong in the instructions. I started it up and it was fine, until the engine started smoking like crazy. A little bit of that blue fluid from one of the lines dripped on the header while i was taking it off... I almost freaked out, until i realized what happened. The smoke had a sweet smell almost __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-24-2013, 09:39 PM	#144 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	yeah, I had it plugged into a hose. __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

02-25-2013, 03:16 AM	#145 (permalink)
chrischhorn A True Z Fanatic Join Date: Jan 2012 Location: Mililani, HI Posts: 1,566 Drives: 2014 Juke Nismo RS Rep Power: 16	Alex, there are 2 hose ports on the back of the manifold. 1 is to loop around to the front for the crank case pressure lines that originally connect in front with 1 of the t's. The other 1 is to be T'd with the vac hose on the back by the firewall and the map sensor goes on the other end and plugs back into where it originally was. Mine is slightly different set up as I just wasn't paying attention but it works fine and I'm too lazy to change it lol. AlexRaymond19 likes this. __________________ R.I.P. 8/01/13 1SlowZ One day I'll have another....

02-25-2013, 07:46 AM	#146 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Ah, gotcha. __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-25-2013, 11:24 AM	#147 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	the intake manifold has nevewr been off before. Wondering if that scratch inside is anything to worry about, or just sub par nissan craftmanshit __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-25-2013, 11:25 AM	#148 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	craftmanship* __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-25-2013, 01:17 PM	#149 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,186 Drives: 2011 Nismo GM 6M Rep Power: 2684437	When the manifold was cast. It looks like someone took a burr bit to it to clean up that area some. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-25-2013, 02:17 PM	#150 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Ahh, has anyone ever taken that off and polished it perfectly smooth? __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Momentum Performance 350Z/G35 Headers	AlexRaymond19	Parts for sale (Private Classifieds)	5	01-25-2013 06:24 AM
Momentum performance headers	UFreefer	Intake/Exhaust	2	01-01-2013 11:00 PM
New Dyno Results From Momentum Headers	SPOHN	Engine & Drivetrain	55	12-15-2012 06:41 PM
Install Video/Sound Clip: FI headers/cat-back/HFC...yes headers AND HFC.	M.Bonanni	Intake/Exhaust	30	08-07-2012 11:07 AM