Installing Momentum Headers

Rusty · 02-10-2013, 06:04 PM

It's down hill from here out.

AlexRaymond19 · 02-10-2013, 07:29 PM

Oh don't tell me that :-( I bought a bottle of captain to celebrate the heat shield coming off. My goal over the next weeks is to get at least 2 bolts off a day. On a side note, my headers did not come with hardware, but my test pipes did, should i reuse the header nuts, or use the TP nuts on the header and the old header nuts on the tp? If that will even work? Or should i buy new bolts at nissan?

Huck · 02-10-2013, 11:55 PM

The header bolts *should* still be in decent condition, and as long as you haven't stripped the header nuts they'll do fine too. Reuse the old hardware unless it's messed up. Congrats on the heatshield! It's a pain I know. The thing to remember now is to go slow on the header nuts, if you start wrenching too fast the socket will come half off an you'll round off the nut, then it's another trip to Nissan lol.

I'm actually driving around with one of the passenger side (I think) header studs sitting in my garage. It came out during the install and for the life of me I can't get te damn thing back in there. The other nuts are tight though so there's no exhaust leaks.

Sent from my iPizzle using magic and new-fangled science stuff

AlexRaymond19 · 02-11-2013, 04:37 PM

So after finally getting the heat shield off yesterday, today after work i got the front 5 bolts off the header, just taking a little smoke break to get the last one. Seems like it is just a straight shot :-) It has only taken me maybe 30 mins including taking off the tire and wheel well liner. Hopefully i did not just jynx myself, but it seems like smooth sailing!

DEpointfive0 · 02-11-2013, 04:40 PM

Smoke break FTW

Rusty · 02-11-2013, 04:42 PM

The heat shield is the hardest part of the whole ordeal.

Megan370z · 02-11-2013, 05:17 PM

i remember the first time I did it on the 370z. That heat sheild on the driver side was a real pain in the *** for the first hour then I decided to work around it, which wasnt too bad..

just one big advise, if one of those stud get off ,, make sure you screw them back in properly and not slightly cross threaded .
I had 1 that I crossthreaded without knowing it ... it wasnt fun at all trying to realign it in the hole since the header didnt fit !

AlexRaymond19 · 02-11-2013, 07:48 PM

Quote:

Originally Posted by Megan370z

i remember the first time I did it on the 370z. That heat sheild on the driver side was a real pain in the *** for the first hour then I decided to work around it, which wasnt too bad..

just one big advise, if one of those stud get off ,, make sure you screw them back in properly and not slightly cross threaded .
I had 1 that I crossthreaded without knowing it ... it wasnt fun at all trying to realign it in the hole since the header didnt fit !

Ill keep that in mind thanks! All bolts out, just have to disconnect the back side of the cats and yank that sucker out. Sucks i can only spend about 45 mins after work everyday...

Huck · 02-12-2013, 01:39 PM

Yeah seriously. I remember I had to take an extra day off of work to get mine done. Major PITA.

Sent from my iPizzle using magic and new-fangled science stuff

chrischhorn · 02-12-2013, 01:47 PM

Quote:

Originally Posted by Huck

Yeah seriously. I remember I had to take an extra day off of work to get mine done. Major PITA.

Sent from my iPizzle using magic and new-fangled science stuff

Ditto. I ended up calling out "sick" to finish this up. lol

Rusty · 02-12-2013, 02:08 PM

Quote:

Originally Posted by AlexRaymond19

Ill keep that in mind thanks! All bolts out, just have to disconnect the back side of the cats and yank that sucker out. Sucks i can only spend about 45 mins after work everyday...

I dropped the stock manifold and cat as one piece. So you don't have to fool with that damn demon bolt.

AlexRaymond19 · 02-12-2013, 08:19 PM

So i have an update! I guess while i was at work the exhaust fairy showed up with my FI exhaust and z1 testpipes

But seriously, put another 45 mins to an hour in and got this bad boy out

Im really hoping to have it all done by this weekend! I want to thank everyone (especially Huck for putting up with my texts) that was kind enough to offer advice and help me out. We really do have a wonderful community here at The370Z!

I will have before and after exhaust clips up by monday at the latest, i believe i will be the first G3, FI non-res, momentum, and Z1 tp combo. Im guessing its going to be stupid loud, what do you think?

Huck · 02-12-2013, 11:35 PM

Lol it IS pretty loud, I have become my neighbors' alarm clock. When I start my car in the morning their picture frames rattle on the wall. Luckily they love me, so they don't mind too much.

Question: you didn't use air tools to get that stuff off did you? I see that your O2 sensors are still in, and the vibrations from air tools could very possibly ruin the sensors. I'd hate to hear that you had to spend $1600+ on 4 new sensors

Don't worry about the texts, I don't mind. I like helping people out and sharing what little knowledge I have lol. Hell, if you were local I would be under the good with you

any other questions don't hesitate to text or call.

Sent from my iPizzle using magic and new-fangled science stuff

AlexRaymond19 · 02-13-2013, 05:56 AM

I did it all by hand :-)

MJB · 02-13-2013, 08:28 AM

OP, congrats! That looks to be a pretty good wrap job on your new headers

02-10-2013, 06:04 PM	#46 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,187 Drives: 2011 Nismo GM 6M Rep Power: 2684437	It's down hill from here out. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-10-2013, 07:29 PM	#47 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Oh don't tell me that :-( I bought a bottle of captain to celebrate the heat shield coming off. My goal over the next weeks is to get at least 2 bolts off a day. On a side note, my headers did not come with hardware, but my test pipes did, should i reuse the header nuts, or use the TP nuts on the header and the old header nuts on the tp? If that will even work? Or should i buy new bolts at nissan? __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-10-2013, 11:55 PM	#48 (permalink)
Huck A True Z Fanatic Join Date: Jan 2012 Location: Cocoa, Florida Age: 42 Posts: 5,075 Drives: Pantydropper machine Rep Power: 33	The header bolts should still be in decent condition, and as long as you haven't stripped the header nuts they'll do fine too. Reuse the old hardware unless it's messed up. Congrats on the heatshield! It's a pain I know. The thing to remember now is to go slow on the header nuts, if you start wrenching too fast the socket will come half off an you'll round off the nut, then it's another trip to Nissan lol. I'm actually driving around with one of the passenger side (I think) header studs sitting in my garage. It came out during the install and for the life of me I can't get te damn thing back in there. The other nuts are tight though so there's no exhaust leaks. Sent from my iPizzle using magic and new-fangled science stuff AlexRaymond19 likes this. __________________ VLEDS \| Evo-R \| Moddiction \| CF Hood Struts \| F.I. CF CBE & LTH \| Stillen CAI \| NST Pulleys \| UpRev \| Z1 \| M7 \| Status \| Forgestar \| PSS \| Whiteline \| SPL \| SPC \| Kenwood \| Zenclosure \| Kicker \| Alpine Type R

02-11-2013, 04:37 PM	#49 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	So after finally getting the heat shield off yesterday, today after work i got the front 5 bolts off the header, just taking a little smoke break to get the last one. Seems like it is just a straight shot :-) It has only taken me maybe 30 mins including taking off the tire and wheel well liner. Hopefully i did not just jynx myself, but it seems like smooth sailing! DEpointfive0 likes this. __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-11-2013, 04:42 PM	#51 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,187 Drives: 2011 Nismo GM 6M Rep Power: 2684437	The heat shield is the hardest part of the whole ordeal. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-11-2013, 04:40 PM	#50 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	Smoke break FTW

02-11-2013, 05:17 PM	#52 (permalink)
Megan370z A True Z Fanatic Join Date: Oct 2009 Location: Canada Posts: 1,156 Drives: 370z Rep Power: 24	i remember the first time I did it on the 370z. That heat sheild on the driver side was a real pain in the *** for the first hour then I decided to work around it, which wasnt too bad.. just one big advise, if one of those stud get off ,, make sure you screw them back in properly and not slightly cross threaded . I had 1 that I crossthreaded without knowing it ... it wasnt fun at all trying to realign it in the hole since the header didnt fit ! __________________ Megan Journal Click Me ....................One Man Team Motorsport Click Me

02-12-2013, 01:39 PM	#54 (permalink)
Huck A True Z Fanatic Join Date: Jan 2012 Location: Cocoa, Florida Age: 42 Posts: 5,075 Drives: Pantydropper machine Rep Power: 33	Yeah seriously. I remember I had to take an extra day off of work to get mine done. Major PITA. Sent from my iPizzle using magic and new-fangled science stuff chrischhorn likes this. __________________ VLEDS \| Evo-R \| Moddiction \| CF Hood Struts \| F.I. CF CBE & LTH \| Stillen CAI \| NST Pulleys \| UpRev \| Z1 \| M7 \| Status \| Forgestar \| PSS \| Whiteline \| SPL \| SPC \| Kenwood \| Zenclosure \| Kicker \| Alpine Type R

02-12-2013, 08:19 PM	#57 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	So i have an update! I guess while i was at work the exhaust fairy showed up with my FI exhaust and z1 testpipes But seriously, put another 45 mins to an hour in and got this bad boy out Im really hoping to have it all done by this weekend! I want to thank everyone (especially Huck for putting up with my texts) that was kind enough to offer advice and help me out. We really do have a wonderful community here at The370Z! I will have before and after exhaust clips up by monday at the latest, i believe i will be the first G3, FI non-res, momentum, and Z1 tp combo. Im guessing its going to be stupid loud, what do you think? ts-c63 and DEpointfive0 like this. __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-12-2013, 11:35 PM	#58 (permalink)
Huck A True Z Fanatic Join Date: Jan 2012 Location: Cocoa, Florida Age: 42 Posts: 5,075 Drives: Pantydropper machine Rep Power: 33	Lol it IS pretty loud, I have become my neighbors' alarm clock. When I start my car in the morning their picture frames rattle on the wall. Luckily they love me, so they don't mind too much. Question: you didn't use air tools to get that stuff off did you? I see that your O2 sensors are still in, and the vibrations from air tools could very possibly ruin the sensors. I'd hate to hear that you had to spend $1600+ on 4 new sensors Don't worry about the texts, I don't mind. I like helping people out and sharing what little knowledge I have lol. Hell, if you were local I would be under the good with you any other questions don't hesitate to text or call. Sent from my iPizzle using magic and new-fangled science stuff __________________ VLEDS \| Evo-R \| Moddiction \| CF Hood Struts \| F.I. CF CBE & LTH \| Stillen CAI \| NST Pulleys \| UpRev \| Z1 \| M7 \| Status \| Forgestar \| PSS \| Whiteline \| SPL \| SPC \| Kenwood \| Zenclosure \| Kicker \| Alpine Type R

02-13-2013, 05:56 AM	#59 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	I did it all by hand :-) __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-13-2013, 08:28 AM	#60 (permalink)
MJB A True Z Fanatic Join Date: Aug 2011 Location: Tacoma, WA Age: 41 Posts: 1,498 Drives: a POS truck Rep Power: 496	OP, congrats! That looks to be a pretty good wrap job on your new headers __________________ 09 Nismo #0483 sold. Viper or C7 next time around.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Momentum Performance 350Z/G35 Headers	AlexRaymond19	Parts for sale (Private Classifieds)	5	01-25-2013 06:24 AM
Momentum performance headers	UFreefer	Intake/Exhaust	2	01-01-2013 11:00 PM
New Dyno Results From Momentum Headers	SPOHN	Engine & Drivetrain	55	12-15-2012 06:41 PM
Install Video/Sound Clip: FI headers/cat-back/HFC...yes headers AND HFC.	M.Bonanni	Intake/Exhaust	30	08-07-2012 11:07 AM