Installing Momentum Headers

Rusty · 02-14-2013, 02:34 PM

Wonder why the differences?

DEpointfive0 · 02-14-2013, 02:36 PM

2009 vs 2011?

Sh0velMan · 02-14-2013, 02:37 PM

Must be. Kinda silly that it isn't keyed on mine lmao.

AlexRaymond19 · 02-14-2013, 08:50 PM

New update, the passenger side header flew off! It was a piece of cake, except for the fact two of the studs came out with the bolts, and i rounded off one bolt on the back side of the cats... Attempted to cut it off with my dremel to no avail, so i just took the y pipe, cat and header off as one piece

I should have just done that in the first place... Tomorrow i will begin the install of the new headers, TPs and CBE

I already installed one 02 sensor on my z1 test pipes. I also purchased bung extenders, and was wondering how much steel wool i should put it them, and what type? I purchased fine grade steel wool, and packed a pretty good amount in there... I actually had to stop and take some out twice, is this a good amount? Thanks!

SS_Firehawk · 02-14-2013, 08:52 PM

CG's! How many day's have you been at it again?

chrischhorn · 02-14-2013, 08:59 PM

Quote:

Originally Posted by Sh0velMan

Must be. Kinda silly that it isn't keyed on mine lmao.

Mine was keyed but my steering wheel did a full spin for whatever reason. Slip light was on but just had a shop reset it rather then actually re-adjusting it lol. The wheel was straight and driving straight since the computer read it was a full 360 degrees off exactly lol.

AlexRaymond19 · 02-14-2013, 09:08 PM

Quote:

Originally Posted by SS_Firehawk

CG's! How many day's have you been at it again?

Ummmmm i lost count! But i have only been putting in 45 mins to an hour everyday. I probably have about 5-6 hours invested of actual wrench time, not including breaks, but including the friggin 2 hours wasted on the heat shield on the drivers side

AlexRaymond19 · 02-15-2013, 06:08 PM

Little update, having a very tough time getting the header in. I called Z1 since they have done the install and they said i have to take all the head studs out... This should only take another 2 hours :-(

DEpointfive0 · 02-15-2013, 06:23 PM

Quote:

Originally Posted by AlexRaymond19

Little update, having a very tough time getting the header in. I called Z1 since they have done the install and they said i have to take all the head studs out... This should only take another 2 hours :-(

Sorry brother... If I was any closer to you I would've loved to help

AlexRaymond19 · 02-15-2013, 08:03 PM

It actually was not too bad, got the header on, just have to finish bolting it down. I'm really shooting to be done in about 2 hours, but i might have to run to the store to grab another u joint...

AlexRaymond19 · 02-15-2013, 09:37 PM

I am seriously thinking about wheeling my car outside, pouring gas all over it, lighting it on fire, and collecting the insurance money... Would probably be easier

Rusty · 02-15-2013, 10:12 PM

Reading this thread is like reading a "comedy of horrors".

Hang in there. It will be done before you know. And you will be very happy listening to it fire up for the first time.

Look at it this way. What you are doing is a character builder.

gomer_110 · 02-15-2013, 10:24 PM

Quote:

Originally Posted by Rusty

Reading this thread is like reading a "comedy of horrors".

Hang in there. It will be done before you know. And you will be very happy listening to it fire up for the first time.

Look at it this way. What you are doing is a character builder.

and saving yourself somewhere in the neighborhood of $700.

Rusty · 02-15-2013, 10:46 PM

Quote:

Originally Posted by gomer_110

and saving yourself somewhere in the neighborhood of $700.

bloody knuckles and all.

chrischhorn · 02-16-2013, 01:40 AM

Quote:

Originally Posted by AlexRaymond19

Little update, having a very tough time getting the header in. I called Z1 since they have done the install and they said i have to take all the head studs out... This should only take another 2 hours :-(

I feel my idea was easier lol. I unbolted the motor mount and raised it a bit to get more clearance to slide it in. Worked like a charm and i didn't have to remove a single head stud lol.

02-14-2013, 02:34 PM	#76 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,220 Drives: 2011 Nismo GM 6M Rep Power: 2684438	Wonder why the differences? __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

02-14-2013, 02:37 PM	#78 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	Must be. Kinda silly that it isn't keyed on mine lmao. __________________ Buy My Car! \| Build Thread

02-14-2013, 08:50 PM	#79 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	New update, the passenger side header flew off! It was a piece of cake, except for the fact two of the studs came out with the bolts, and i rounded off one bolt on the back side of the cats... Attempted to cut it off with my dremel to no avail, so i just took the y pipe, cat and header off as one piece I should have just done that in the first place... Tomorrow i will begin the install of the new headers, TPs and CBE I already installed one 02 sensor on my z1 test pipes. I also purchased bung extenders, and was wondering how much steel wool i should put it them, and what type? I purchased fine grade steel wool, and packed a pretty good amount in there... I actually had to stop and take some out twice, is this a good amount? Thanks! __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-14-2013, 08:52 PM	#80 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	CG's! How many day's have you been at it again? __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

02-15-2013, 06:08 PM	#83 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Little update, having a very tough time getting the header in. I called Z1 since they have done the install and they said i have to take all the head studs out... This should only take another 2 hours :-( __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-14-2013, 02:36 PM	#77 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	2009 vs 2011?

02-15-2013, 08:03 PM	#85 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	It actually was not too bad, got the header on, just have to finish bolting it down. I'm really shooting to be done in about 2 hours, but i might have to run to the store to grab another u joint... __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-15-2013, 09:37 PM	#86 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	I am seriously thinking about wheeling my car outside, pouring gas all over it, lighting it on fire, and collecting the insurance money... Would probably be easier __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

02-15-2013, 10:12 PM	#87 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,220 Drives: 2011 Nismo GM 6M Rep Power: 2684438	Reading this thread is like reading a "comedy of horrors". Hang in there. It will be done before you know. And you will be very happy listening to it fire up for the first time. Look at it this way. What you are doing is a character builder. AlexRaymond19 likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Momentum Performance 350Z/G35 Headers	AlexRaymond19	Parts for sale (Private Classifieds)	5	01-25-2013 06:24 AM
Momentum performance headers	UFreefer	Intake/Exhaust	2	01-01-2013 11:00 PM
New Dyno Results From Momentum Headers	SPOHN	Engine & Drivetrain	55	12-15-2012 06:41 PM
Install Video/Sound Clip: FI headers/cat-back/HFC...yes headers AND HFC.	M.Bonanni	Intake/Exhaust	30	08-07-2012 11:07 AM