Hey Z1. ETA on those headers?

XwChriswX · 07-30-2013, 10:47 PM

Quote:

Originally Posted by Eighties Meta

I can't post the email from Z1 because obviously they have a disclaimer stating you can't repost however that is what I was told. believe it or not.

I'm not trying to discredit you, or Z1. You're both good people.

Just that it seems kind of odd to say that a certain setup is "capped" at a specific HP level, when we all know that there are so many variables that go into play when dynoing that it could read anything the owner would.... or would not, want to see.

Eighties Meta · 07-31-2013, 12:15 AM

I think it was more based on my setup of full boltons then installing these headers would cap me around 324 unl3ss I went test ipes or art. I ordered this stuff 06/5 and I believe the parts have arrived at aam but I havent picked a shop here in houston yet to ship them to for the installation. Seems like its taking forever

Sent from my GT-N8013 using Tapatalk 2

XwChriswX · 07-31-2013, 12:17 AM

Quote:

Originally Posted by Eighties Meta

I think it was more based on my setup of full boltons then installing these headers would cap me around 324 unl3ss I went test ipes or art. I ordered this stuff 06/5 and I believe the parts have arrived at aam but I havent picked a shop here in houston yet to ship them to for the installation. Seems like its taking forever

I'm looking forward to your progress, and to see just where you do end up at.

brucelidat · 07-31-2013, 01:23 AM

Yes, I believe these are just estimates based on their experiences. They estimated with the headers and HFCs, I could probably pull about 320whp, a few more if I had CAI, and probably 330s with TPs. Dynos obviously vary so these are just estimate on what you can expect with certain mods. It's nothing official.

chrischhorn · 07-31-2013, 03:16 AM

Quote:

Originally Posted by Yutnaka

I spoke to Jon couple months back and said the same thing. He also did say thay with the Tomei single exhaust, the shop car made 346whps.

WANT!!!!

SPOHN · 07-31-2013, 06:51 AM

I want the Tomei exhaust. But they need to make a 3" Y pipe

XwChriswX · 07-31-2013, 11:28 AM

Quote:

Originally Posted by brucelidat

Yes, I believe these are just estimates based on their experiences. They estimated with the headers and HFCs, I could probably pull about 320whp, a few more if I had CAI, and probably 330s with TPs. Dynos obviously vary so these are just estimate on what you can expect with certain mods. It's nothing official.

My thoughts are what will these headers do with MD ART pipes and an FI cbe...

Cause that's my plan. I will most likely have to do HFCs due to state regulations, but ART pipes would be my desired path.

brucelidat · 07-31-2013, 04:11 PM

You'd be in line with me then since I have a FI cbe.

ZBro16 · 07-31-2013, 04:12 PM

I like their headers, but I will buy only when I can use the FI RTPs. Until then, I wait =)

the horse is dead and i just punched it.

brucelidat · 07-31-2013, 04:36 PM

with all the interest in this thread, z1 wil def get it done with the HR flange

NismoZ70 · 07-31-2013, 05:38 PM

Quote:

Originally Posted by brucelidat

with all the interest in this thread, z1 wil def get it done with the HR flange

They had said that they would be creating headers with the HR flange in the near future. It's just a matter of when it will happen. Also they mentioned that it would be an additional $150-$200 with the HR flange version.

Joepro · 08-01-2013, 08:52 AM

Quote:

Originally Posted by NismoZ70

They had said that they would be creating headers with the HR flange in the near future. It's just a matter of when it will happen. Also they mentioned that it would be an additional $150-$200 with the HR flange version.

Not worth it IMO over a flange shape, as said before test pipes are less expensive as well...you could buy this setup, save at least 300 bucks now(or maybe more later if they raise the base price), then sell or scrap your oe cats and buy de cats if you really needed them, plenty avaliable on other forums, plus no waiting, these make power, the butt dyno told me, and the real dyno will tell me on august 13th.

MM'08_350Z · 08-02-2013, 10:00 PM

Well guys my HR going into the shop to install the Z1 headers and Z1 test pipes, plus bored out throttle bodies, NST pulleys and a retune. Lets hope for better numbers.

- Manny

2sl0w · 08-05-2013, 09:23 PM

Quote:

Originally Posted by MM'08_350Z

Well guys my HR going into the shop to install the Z1 headers and Z1 test pipes, plus bored out throttle bodies, NST pulleys and a retune. Lets hope for better numbers.

- Manny

No need to hope.

it should definitely make more power.

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

Joepro · 08-06-2013, 12:49 PM

T minus one week till tune day!

07-31-2013, 12:15 AM	#302 (permalink)
Eighties Meta Enthusiast Member Join Date: Aug 2012 Location: Pasadena, MD Age: 54 Posts: 344 Drives: 09 370z 7AT no-sport Rep Power: 13	I think it was more based on my setup of full boltons then installing these headers would cap me around 324 unl3ss I went test ipes or art. I ordered this stuff 06/5 and I believe the parts have arrived at aam but I havent picked a shop here in houston yet to ship them to for the installation. Seems like its taking forever Sent from my GT-N8013 using Tapatalk 2 __________________ 2009 370z Touring 7AT/AAM 2.5 true dual exhaust/AAM DE test pipes/z1 vqde35 headers/AAM cold air intake (R-line)/Motordyne M370/Quaife LSD/z1 brake upgd pkg/Swift Spec-R springs/WhiteLine Front&Rear sway bars with endlinks

07-31-2013, 01:23 AM	#304 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	Yes, I believe these are just estimates based on their experiences. They estimated with the headers and HFCs, I could probably pull about 320whp, a few more if I had CAI, and probably 330s with TPs. Dynos obviously vary so these are just estimate on what you can expect with certain mods. It's nothing official. __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

07-31-2013, 06:51 AM	#306 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 46 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	I want the Tomei exhaust. But they need to make a 3" Y pipe ZBro16 likes this. __________________ Last edited by SPOHN; 07-31-2013 at 05:20 PM.

07-31-2013, 04:11 PM	#308 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	You'd be in line with me then since I have a FI cbe. __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

07-31-2013, 04:36 PM	#310 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	with all the interest in this thread, z1 wil def get it done with the HR flange __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

07-31-2013, 04:12 PM	#309 (permalink)
ZBro16 Enthusiast Member Join Date: Nov 2011 Location: Huntsville, AL Posts: 370 Drives: A Z. Rep Power: 14	I like their headers, but I will buy only when I can use the FI RTPs. Until then, I wait =) the horse is dead and i just punched it.

08-02-2013, 10:00 PM	#313 (permalink)
MM'08_350Z Base Member Join Date: Jun 2013 Location: Laredo Posts: 36 Drives: 08 350Z CS M6 Rep Power: 12	Well guys my HR going into the shop to install the Z1 headers and Z1 test pipes, plus bored out throttle bodies, NST pulleys and a retune. Lets hope for better numbers. - Manny 370Z JT likes this.

08-06-2013, 12:49 PM	#315 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 34	T minus one week till tune day! __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AMS Headers	SPOHN	Intake/Exhaust	24	12-20-2012 01:16 AM
Install Video/Sound Clip: FI headers/cat-back/HFC...yes headers AND HFC.	M.Bonanni	Intake/Exhaust	30	08-07-2012 11:07 AM
[WTB] Headers	Dwv2005	Parts for sale (Private Classifieds)	3	02-29-2012 08:17 PM
headers	Ricardo2.0	Wanted	0	01-24-2012 01:37 AM
Headers	Paladinjc	Intake/Exhaust	12	04-08-2011 06:36 PM