I have these on my 2010 manual z. Along with the Ark Grip True Dual exhaust, Stillen headers, and Stillen G3 intake. I LOVE the sound. But since i put
|
|
LinkBack | Thread Tools | Display Modes |
01-30-2013, 08:11 PM | #16 (permalink) |
Base Member
Join Date: Sep 2012
Location: Center Point, LA
Posts: 208
Drives: 2014 Nissan Z Nismo
Rep Power: 13 |
I have these on my 2010 manual z. Along with the Ark Grip True Dual exhaust, Stillen headers, and Stillen G3 intake. I LOVE the sound. But since i put the Ark R Spec test pipes and exhaust on, i threw a service engine code. It was expected though. Now just for a tune. But this is a great product imo!
|
01-31-2013, 04:18 PM | #19 (permalink) | |
A True Z Fanatic
Join Date: May 2009
Location: Sugar Land
Posts: 3,692
Drives: 97' Ranger :)
Rep Power: 24 |
Quote:
|
|
01-31-2013, 07:39 PM | #21 (permalink) |
Base Member
Join Date: Sep 2012
Location: Center Point, LA
Posts: 208
Drives: 2014 Nissan Z Nismo
Rep Power: 13 |
Well the only complaint i had was with the true dual exhaust. It sat on the brace underneath my car but i put some washers to give it some room between the two and its been fine since then!
|
02-03-2013, 01:02 AM | #22 (permalink) |
A True Z Fanatic
Join Date: Aug 2011
Location: palmdale, ca
Posts: 1,299
Drives: 2010 nissan 370z
Rep Power: 16 |
It didn't for me, I installed them today, reset the ecu and withing 30 miles.....SES again. Waste of 50 bucks...any other solutions? Im getting P0420 and P0430
__________________
https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)- |
02-03-2013, 01:04 AM | #23 (permalink) |
A True Z Fanatic
Join Date: Aug 2011
Location: palmdale, ca
Posts: 1,299
Drives: 2010 nissan 370z
Rep Power: 16 |
you need to loosen the bolts on the y-pipe use your floor jack and put some serious pressure on the y to clear from the brace. I did the same thing the 1st time I installed and test drove. Next day i jacked the car up and took the advice from other members...I pushed it so that it touched the top of the car with the jack...when released it sat perfectly in the middle.
__________________
https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)- |
02-03-2013, 01:45 PM | #25 (permalink) |
A True Z Fanatic
Join Date: Aug 2011
Location: palmdale, ca
Posts: 1,299
Drives: 2010 nissan 370z
Rep Power: 16 |
problem is in cali if i block off the 02 sensors in uprev, the smog check will see that. Thats why I was hoping that the bung extensions would fix it. I plan on getting uprev after I get the motordyne intake
__________________
https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)- |
02-04-2013, 12:54 PM | #26 (permalink) |
Track Member
Join Date: Jul 2009
Location: CHINO
Posts: 957
Drives: Black 350z/370z
Rep Power: 17 |
The bung extensions usually fix issues but if it doesnt you can try a L-bung but those usually don't clear our resonator. An UpRev tune would definitely "fix" the problem...
|
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ERZ Performance High Flow Cats, Install and Review Thread | spearfish25 | Intake/Exhaust | 219 | 02-20-2013 09:33 AM |
Hi-Flow Cats vs. Resonated Cat Pipes | birdseed404 | Intake/Exhaust | 28 | 12-10-2012 07:04 PM |
WTT: ERZ High Flow Cats for good OEM Cats with low miles only (15k or less) | '10Anamoly | Wanted | 4 | 09-14-2011 06:42 PM |
ERZ Performance High Flow Cats | spearfish25 | Intake/Exhaust | 24 | 05-10-2011 05:59 PM |
09 nismo cbe/new f.i resonated high flow cats | dark_nismo | Parts for sale (Private Classifieds) | 8 | 03-30-2011 02:16 PM |