Post FI HFCs Install/ SES or CEL Help!!

eastwest2300 · 12-28-2012, 09:09 AM

Quote:

Originally Posted by Sh0velMan

You use an impact on the demon bolt? Anything at all other than a ratchet/wrench?

Did you beat on the ratchet/wrench with a hammer?

Dude, we did EVERYTHING humanly possible to get that fricken bolt off.

eastwest2300 · 12-28-2012, 09:09 AM

Im not even kidding. Im dead serious bro.

Sh0velMan · 12-28-2012, 09:22 AM

Quote:

Originally Posted by eastwest2300

Im not even kidding. Im dead serious bro.

Then that sensor is dead.

They're really quite fragile.

MyKindaGuise · 12-28-2012, 09:25 AM

Quote:

Originally Posted by Sh0velMan

You use an impact on the demon bolt? Anything at all other than a ratchet/wrench?

Did you beat on the ratchet/wrench with a hammer?

We pretty much used every possible combination you can think of. By far the worst demon bolt we have ever dealt with.

MyKindaGuise · 12-28-2012, 09:27 AM

Quote:

Originally Posted by Sh0velMan

Then that sensor is dead.

They're really quite fragile.

That still doesnt explain how its the manifold O2. Ive never broken an o2 before either.

EW ill you send pics of where this o2 is at then.

MJB · 12-28-2012, 09:29 AM

Quote:

Originally Posted by MyKindaGuise

I dont see how it couldve been damaged on install. That error code relates to the sensor on the manifolds not the cats. That is a precat o2 code. Those were not touched at all during install of the hfc's. Did you make sure atleast that sensors are plugged in and are not loose in anyway?

Just the vibration alone from impact wrench can damage those sensors, even the ones on the manifolds. I've seen it happen with the 350z guys. Hopefully that's not the case with the OP, but it's sorts sounding like that's the case.

Sh0velMan · 12-28-2012, 09:31 AM

Quote:

Originally Posted by MyKindaGuise

That still doesnt explain how its the manifold O2. Ive never broken an o2 before either.

EW ill you send pics of where this o2 is at then.

The demon bolt connects the cat to the Manifold.. Any vibration put into that bolt is going to rattle everything in the system, but especially the manifold itself. The O2 sensor we're talking about is like 1.5-2 inches tops from that bolt...

It's dead, Jim.

eastwest2300 · 12-28-2012, 09:34 AM

Quote:

Originally Posted by MyKindaGuise

That still doesnt explain how its the manifold O2. Ive never broken an o2 before either.

EW ill you send pics of where this o2 is at then.

thank you soo much bro, please.. please do that.

Sh0velMan · 12-28-2012, 09:34 AM

Quote:

Originally Posted by MyKindaGuise

That still doesnt explain how its the manifold O2. Ive never broken an o2 before either.

EW ill you send pics of where this o2 is at then.

attached.

eastwest2300 · 12-28-2012, 09:35 AM

Quote:

Originally Posted by MJB

Just the vibration alone from impact wrench can damage those sensors, even the ones on the manifolds. I've seen it happen with the 350z guys. Hopefully that's not the case with the OP, but it's sorts sounding like that's the case.

Im leaning that way too, I've already started looking for replacements. I found a couple of them (used) on eBay. What do you guys think? good idea or bad getting them off eBay?

Sh0velMan · 12-28-2012, 09:36 AM

Quote:

Originally Posted by eastwest2300

Im leaning that way too, I've already started looking for replacements. I found a couple of them (used) on eBay. What do you guys think? good idea or bad getting them off eBay?

Personally I'd get them from the dealer only.

Just me, tho.

They're expensive as ****, too. Had to buy a couple due to a few 'issues' after the header install..grumble grumble..

eastwest2300 · 12-28-2012, 09:37 AM

Quote:

Originally Posted by Sh0velMan

attached.

Thank you soo much man.

eastwest2300 · 12-28-2012, 09:38 AM

Quote:

Originally Posted by Sh0velMan

Personally I'd get them from the dealer only.

Just me, tho.

They're expensive as ****, too. Had to buy a couple due to a few 'issues' after the header install..grumble grumble..

I found them new for $125 on eBay. They are pricey as sh!t.

eastwest2300 · 12-28-2012, 09:39 AM

Shovelman, will I be able to see it from looking over the engine? do you think?

Sh0velMan · 12-28-2012, 09:40 AM

Quote:

Originally Posted by eastwest2300

Shovelman, will I be able to see it from looking over the engine? do you think?

Take off the brace, engine cover, and maybe intake tubes, and yeah you should be able to get to it from the top.

Edit: Oh and it'll be stuck on there pretty good. Invest in a high quality O2 socket and some anti-seize for the new one.

12-28-2012, 09:09 AM	#32 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,973 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	Im not even kidding. Im dead serious bro. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

12-28-2012, 09:39 AM	#44 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,973 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	Shovelman, will I be able to see it from looking over the engine? do you think? __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
External Wastegates Post Install - Possible?	DIGItonium	Forced Induction	7	05-25-2012 02:53 PM
Z1 post MAF hose install problem	USAFZDRIVER	Intake/Exhaust	16	05-03-2012 04:21 AM
Asap help with aftermarket install post	Carbon_z	Audio & Video	5	11-01-2010 09:25 PM
shop or person to install HFCs in NY?	toxik	North East Region	11	05-16-2010 06:49 PM
Stillen Headers + Berk HFCs self-install report	wstar	Intake/Exhaust	84	04-14-2009 01:09 PM