Fast Intentions exhaust is here!

theART · 11-02-2011, 02:04 AM

Any feedback on road clearance of the muffler cans?

Looking at the pic it seems lower than stock pipes.

brucelidat · 11-02-2011, 02:19 AM

Quote:

Originally Posted by theART

Any feedback on road clearance of the muffler cans?

Looking at the pic it seems lower than stock pipes.

Tony told me the new design that they've been using for a few months now is a little bit higher than the older ones. Not sure what the clearance is though. I will get mine installed in a week or 2 but I'm at stock height so it doesn't worry me much.

pedZ · 11-02-2011, 09:27 AM

Quote:

Originally Posted by theART

Any feedback on road clearance of the muffler cans?

Looking at the pic it seems lower than stock pipes.

Yeah, it hangs lower. Check out the end of the first post on this thread. It has a picture measuring the clearance on a lowered Z.

Fast Intentions CBE with 18’’ Resonators Review

For what it's worth, I have not had any clearance issues with it, but my Z is not lowered either.

Doug&Michelle · 11-02-2011, 09:42 AM

I swear I'm about to go nuts! What number are we up to now Tony?

brucelidat · 11-02-2011, 03:17 PM

I am going to call him tomorrow. We are trying to get my install (#398) in for next Friday, the 11th.

limaecho · 11-02-2011, 03:54 PM

Tony - I have called your office and left a message as you are out of town. I am from Australia - interested in getting the 18" resonated system.

I have GT Haus and I feel its too loud for me. Its a good system but not for me.

XwChriswX · 11-02-2011, 04:01 PM

Quote:

Originally Posted by theART

Any feedback on road clearance of the muffler cans?

Looking at the pic it seems lower than stock pipes.

Quote:

Originally Posted by brucelidat

Tony told me the new design that they've been using for a few months now is a little bit higher than the older ones. Not sure what the clearance is though. I will get mine installed in a week or 2 but I'm at stock height so it doesn't worry me much.

Quote:

Originally Posted by pedelg24

Yeah, it hangs lower. Check out the end of the first post on this thread. It has a picture measuring the clearance on a lowered Z.

Fast Intentions CBE with 18’’ Resonators Review

For what it's worth, I have not had any clearance issues with it, but my Z is not lowered either.

The new design hangs a bit higher than the old one, but I've had mine on for over a year now (old design) and I'm lowered 1" all around and have never once scraped.

Careful and correct approaches will save you.

theART · 11-02-2011, 05:36 PM

Quote:

Originally Posted by XwChriswX

Careful and correct approaches will save you.

My exact though, I don't want to think about correct approaches if it's not lowered, sometimes I drive rough without thinking about terrain.

Good to know that old one was 4" lowered, and new one should be higher.

Thanks

XwChriswX · 11-02-2011, 05:39 PM

Quote:

Originally Posted by theART

My exact though, I don't want to think about correct approaches if it's not lowered, sometimes I drive rough without thinking about terrain.

Good to know that old one was 4" lowered, and new one should be higher.

Thanks

There have been a few times where you just zone out while driving then don't realize the curb/speedbump until you're right up on it and it's like oh ****!! skkkrrrreeeeeeecccchhhhhhh creep over cringing... No scrape.

Like a boss. :|

bigdog1250 · 11-02-2011, 08:12 PM

My cars dropped 1.5" and the cans seem plenty safe. It's mainly when you go over speed bumps that you want to make sure the axel hits it straight on as opposed to at an angle. So once the front lip gets over, you straighten out quickly.

The front of my car scrapes on everything if I'm not careful.

XwChriswX · 11-02-2011, 08:14 PM

Quote:

Originally Posted by bigdog1250

My cars dropped 1.5" and the cans seem plenty safe. It's mainly when you go over speed bumps that you want to make sure the axel hits it straight on as opposed to at an angle. So once the front lip gets over, you straighten out quickly.

The front of my car scrapes on everything if I'm not careful.

My front does the same thing. My dealer never installed the front sport lip trim which I'm glad, that thing would be gone by now

I scrape that very bottom lip of the front bumper that sticks down, but I'm fine with that so long as the front of the bumper itself doesn't scrape. I also have some problems with being caught on a bad driveway exit that is like a /\ and no matter how much angle you have, you still scrape on the underbody...

brucelidat · 11-02-2011, 08:47 PM

Quote:

Originally Posted by bigdog1250

My cars dropped 1.5" and the cans seem plenty safe. It's mainly when you go over speed bumps that you want to make sure the axel hits it straight on as opposed to at an angle. So once the front lip gets over, you straighten out quickly.

The front of my car scrapes on everything if I'm not careful.

So are you saying I shouldn't go over dips and bumps at an angle? Also, I have a lot of speedbumps in my parking structure. I usually go over them with just my passenger side wheel while my driver's side goes between the 2 bumps. Should I avoid this and just go over it squarely with both wheels after I get the exhaust?

XwChriswX · 11-02-2011, 08:48 PM

Quote:

Originally Posted by brucelidat

So are you saying I shouldn't go over dips and bumps at an angle? Also, I have a lot of speedbumps in my parking structure. I usually go over them with just my passenger side wheel while my driver's side goes between the 2 bumps. Should I avoid this and just go over it squarely with both wheels after I get the exhaust?

You can angle over the front, but make sure the back axle his squarely. Going over with just 1 wheel is a really bad way to do so since you don't know exactly how far everything is. If you have split bumps, best way to do it is take the gap between the bumps down the center so you have the most clearance possible...

bigdog1250 · 11-02-2011, 08:59 PM

Quote:

Originally Posted by XwChriswX

You can angle over the front, but make sure the back axle his squarely. Going over with just 1 wheel is a really bad way to do so since you don't know exactly how far everything is. If you have split bumps, best way to do it is take the gap between the bumps down the center so you have the most clearance possible...

^ Precisely

F.I. Inc. · 11-02-2011, 09:22 PM

Quote:

Originally Posted by limaecho

Tony - I have called your office and left a message as you are out of town. I am from Australia - interested in getting the 18" resonated system.

I have GT Haus and I feel its too loud for me. Its a good system but not for me.

I had the message forwarded to me. I am currently in Las Vegas at the SEMA show. Have to represent the company. I will be back to work first thing Friday. I will get back with you then for sure.

Thank you for your patience...

Tony

11-02-2011, 03:17 PM	#6725 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	I am going to call him tomorrow. We are trying to get my install (#398) in for next Friday, the 11th. __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

11-02-2011, 08:12 PM	#6730 (permalink)
bigdog1250 Track Member Join Date: Nov 2008 Location: San Francisco Posts: 846 Drives: 991.2 GT3 Rep Power: 18	My cars dropped 1.5" and the cans seem plenty safe. It's mainly when you go over speed bumps that you want to make sure the axel hits it straight on as opposed to at an angle. So once the front lip gets over, you straighten out quickly. The front of my car scrapes on everything if I'm not careful. __________________ 350z / 40th 370z / C6 Z06 / BMW M4 / V10 R8 / C7 Grand Spot / 997.1 GT3 / S2K / Camaro ZL1 / 718 GTS / 991.2 GT3

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fast girls, Fast cars, One wild ride- Sports Illustrated Swimsuit 2009	Venomous01	Nissan 370Z Photos / Spyshots / Video / Media Gallery	5	01-25-2013 10:27 AM
the Fast and the....	arcticreaver	The Lounge (Off Topic)	1	05-04-2009 05:48 PM
Fast girls, Fast cars, One wild ride- Sports Illustrated Swimsuit 2009	zero	Nissan 370Z Photos / Spyshots / Video / Media Gallery	33	02-26-2009 10:14 PM
Fast Intentions needs prototype!!!	F.I. Inc.	Intake/Exhaust	28	02-16-2009 07:35 AM

11-02-2011, 02:04 AM	#6721 (permalink)
theART Base Member Join Date: Feb 2009 Location: BC Posts: 163 Drives: To Drive Rep Power: 7822	Any feedback on road clearance of the muffler cans? Looking at the pic it seems lower than stock pipes.

11-02-2011, 09:42 AM	#6724 (permalink)
Doug&Michelle Base Member Join Date: Jan 2011 Location: Tulsa, Oklahoma Posts: 176 Drives: '09 370z Tourng Auto Rep Power: 14	I swear I'm about to go nuts! What number are we up to now Tony?

11-02-2011, 03:54 PM	#6726 (permalink)
limaecho Base Member Join Date: Aug 2011 Location: australia Posts: 15 Drives: 10 370Z Roadster Rep Power: 14	Tony - I have called your office and left a message as you are out of town. I am from Australia - interested in getting the 18" resonated system. I have GT Haus and I feel its too loud for me. Its a good system but not for me.