Fast Intentions exhaust is here!

wstar · 07-10-2009, 01:43 PM

Quote:

Originally Posted by F.I. Inc.

Where did you see 4 runs?

We only did three!

He's counting the baseline. The 3 graphs posted are all graphed against the baseline run, which is the fourth one he's looking for. It's in all of the other 3

LiquidZ · 07-10-2009, 01:44 PM

Hood open or closed on the dyno?

kannibul · 07-10-2009, 01:45 PM

Quote:

Originally Posted by Caravanshaka

Just what I wanted to hear! Thanks Tony

don't talk about hot and muggy til you come down to texas

You guys need to keep that hot muggy crap down there....

I guess Kansas sucks too much though

Caravanshaka · 07-10-2009, 02:00 PM

Quote:

Originally Posted by kannibul

You guys need to keep that hot muggy crap down there....

I guess Kansas sucks too much though

lol, by Kansas you mean Oklahoma?

F.I. Inc. · 07-10-2009, 02:00 PM

Quote:

Originally Posted by LiquidZ

Hood open or closed on the dyno?

Open, of course with a fan blowing on if from about 6-8 feet away.

kannibul · 07-10-2009, 02:07 PM

Quote:

Originally Posted by Caravanshaka

lol, by Kansas you mean Oklahoma?

Nah, the wind doesn't stop here

F.I. Inc. · 07-10-2009, 02:25 PM

UPDATED-

Thank you to our newest customer- Kolya

Digtonium: 001 - Pre ordered since April
Tonmed123: 002
Import111: 003
Zat Zuma: 004
Dszombiex: 005
FuszNissan: 006
Crbn_Fbr: 007
Phelan: 008
Kolya: 009 - Installation August 3rd

semtex · 07-10-2009, 02:55 PM

Tony,

I have a fitment question for you. I currently already have a full exhaust setup with Stillen headers, Berk HFCs, and the Stillen CBE. Now, I did the headers last, and when I installed the headers, they changed the geometry ever so slightly, resulting in an alignment issue between the cats and the CBE. This picture shows what I mean:

If I jump ship and swap out my Stillen CBE for yours, do you anticipate I'll have to deal with the same issue? Or does your CBE have a lot of 'wiggle-room' in terms of adjustment? Because uh, Stillen's CBE doesn't. I was able to get Stillen's CBE to connect and my current setup works just fine, but it was a pain getting it to fit right. I don't want to go through that again, if you know what I mean.

Caravanshaka · 07-10-2009, 03:00 PM

Quote:

Originally Posted by semtex

If I jump ship and swap out my Stillen CBE for yours, do you anticipate I'll have to deal with the same issue? Or does your CBE have a lot of 'wiggle-room' in terms of adjustment? Because uh, Stillen's CBE doesn't. I was able to get Stillen's CBE to connect and my current setup works just fine, but it was a pain getting it to fit right. I don't want to go through that again, if you know what I mean.

Sounds like it is a Stillen header fitment issue, not cat or exhaust. I would suspect any cat-back you get will run into that same issue unless you swap out the headers.

F.I. Inc. · 07-10-2009, 03:05 PM

If the headers are not designed to end in the exact factory location then it will throw everything else off. We will assume that your cats are built to factory specs. as well as your cat back starts in factory location. Then process of elimination tells us that it is your headers.

Now, my system has very little wiggle room. It is designed to fit in factory location. If the parts in front of it are not to factory specs. like I said, it will throw it off like your current situation.

This is what I was getting at about flex joints. Say you had flex joints in your current cat back, then you could fudge it and make it fit. All it is going to do is leave your exhaust in a bind and you are going to eventually blow out that flex joint.

wstar · 07-10-2009, 03:11 PM

I'm not sure exactly what part causes that alignment issue TBH. But the Stillen headers do seem to end in the right spot, I think we compared this in another thread, re: two cars with the Berk HFCs and Stillen CBE, but one had headers and one didn't.

semtex · 07-10-2009, 03:13 PM

Yep, I agree that it's the headers. So the rest of you -- be forewarned about the fitment of Stillen's headers! To make things line up correctly, I had to put hose clamps around the rubber hangers and compress them to raise the rear of the exhaust up. It sounds like I'd have to do the same with your exhaust. (You have a PM from me for pricing, btw.)

semtex · 07-10-2009, 03:15 PM

Quote:

Originally Posted by wstar

I'm not sure exactly what part causes that alignment issue TBH. But the Stillen headers do seem to end in the right spot, I think we compared this in another thread, re: two cars with the Berk HFCs and Stillen CBE, but one had headers and one didn't.

Well, I did the headers last. And everything lined up perfectly until the headers went in. So take from that what you will. We're talking about a variance of an inch or so, so the Stillen headers not ending in the right spot wouldn't be obvious to the naked eye. Until you try to bolt up the CBE, that is.

wstar · 07-10-2009, 03:49 PM

Quote:

Originally Posted by semtex

Well, I did the headers last. And everything lined up perfectly until the headers went in. So take from that what you will. We're talking about a variance of an inch or so, so the Stillen headers not ending in the right spot wouldn't be obvious to the naked eye. Until you try to bolt up the CBE, that is.

Yeah that does seem to point at the headers then. FWIW I had the headers and cats installed with the stock CBE at first and nothing was out of whack there though. Then again the stock CBE has those flex joints to help out.

With a 3-vendor setup (Stillen Headers, Berk HFC, FI CBE) it will be interesting

280z/300zx · 07-10-2009, 06:08 PM

Quote:

Originally Posted by F.I. Inc.

Where did you see 4 runs?

We only did three!

I know you only did 3 runs but you mentioned 4. Here is an excerpt again from your post

"HFC runs were about 30 minutes after that."

Yet you didn't post a graph with a dyno test for HFC. Just wondering if you did a run for HFC or only for the test pipes.

07-10-2009, 01:44 PM	#332 (permalink)
LiquidZ A True Z Fanatic Join Date: Nov 2008 Location: Columbus, OH Posts: 1,940 Drives: Mag. Black 2009 370Z Rep Power: 705	Hood open or closed on the dyno? __________________

07-10-2009, 02:25 PM	#337 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	*UPDATED-* Thank you to our newest customer- Kolya Digtonium: 001 - Pre ordered since April Tonmed123: 002 Import111: 003 Zat Zuma: 004 Dszombiex: 005 FuszNissan: 006 Crbn_Fbr: 007 Phelan: 008 Kolya: 009 - Installation August 3rd __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION" Last edited by F.I. Inc.; 07-10-2009 at 11:54 PM.

07-10-2009, 02:55 PM	#338 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 32	Fitment question Tony, I have a fitment question for you. I currently already have a full exhaust setup with Stillen headers, Berk HFCs, and the Stillen CBE. Now, I did the headers last, and when I installed the headers, they changed the geometry ever so slightly, resulting in an alignment issue between the cats and the CBE. This picture shows what I mean: If I jump ship and swap out my Stillen CBE for yours, do you anticipate I'll have to deal with the same issue? Or does your CBE have a lot of 'wiggle-room' in terms of adjustment? Because uh, Stillen's CBE doesn't. I was able to get Stillen's CBE to connect and my current setup works just fine, but it was a pain getting it to fit right. I don't want to go through that again, if you know what I mean. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

07-10-2009, 03:05 PM	#340 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	If the headers are not designed to end in the exact factory location then it will throw everything else off. We will assume that your cats are built to factory specs. as well as your cat back starts in factory location. Then process of elimination tells us that it is your headers. Now, my system has very little wiggle room. It is designed to fit in factory location. If the parts in front of it are not to factory specs. like I said, it will throw it off like your current situation. This is what I was getting at about flex joints. Say you had flex joints in your current cat back, then you could fudge it and make it fit. All it is going to do is leave your exhaust in a bind and you are going to eventually blow out that flex joint. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION"

07-10-2009, 03:11 PM	#341 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3594	I'm not sure exactly what part causes that alignment issue TBH. But the Stillen headers do seem to end in the right spot, I think we compared this in another thread, re: two cars with the Berk HFCs and Stillen CBE, but one had headers and one didn't. __________________ 7AT Track Car! Journal thread / Car setup details

07-10-2009, 03:13 PM	#342 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 32	Yep, I agree that it's the headers. So the rest of you -- be forewarned about the fitment of Stillen's headers! To make things line up correctly, I had to put hose clamps around the rubber hangers and compress them to raise the rear of the exhaust up. It sounds like I'd have to do the same with your exhaust. (You have a PM from me for pricing, btw.) __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fast girls, Fast cars, One wild ride- Sports Illustrated Swimsuit 2009	Venomous01	Nissan 370Z Photos / Spyshots / Video / Media Gallery	5	01-25-2013 10:27 AM
the Fast and the....	arcticreaver	The Lounge (Off Topic)	1	05-04-2009 05:48 PM
Fast girls, Fast cars, One wild ride- Sports Illustrated Swimsuit 2009	zero	Nissan 370Z Photos / Spyshots / Video / Media Gallery	33	02-26-2009 10:14 PM
Fast Intentions needs prototype!!!	F.I. Inc.	Intake/Exhaust	28	02-16-2009 07:35 AM