Stillen g3 intake

ZforMe · 06-12-2009, 10:55 PM

Modshack,

Would the idea be to finish fabricating and then develope a kit to sell to forum members (assuming everything works out well)?

Modshack · 06-12-2009, 11:14 PM

Quote:

Originally Posted by ZforMe

Modshack,

Would the idea be to finish fabricating and then develope a kit to sell to forum members (assuming everything works out well)?

We'll see!

370NUTZ · 06-14-2009, 10:18 AM

Quote:

Originally Posted by NewlyIMPORTed

so i decided to bite the bullet and buy the ultra long tube intake for my 370 with my graduation money. well i was a little upset that i just compulsively went to forged and ordered it. so i get it back and after the bogging from the ecu reseting i didn't really notice a change. well i drove it the next day and i def noticed the change it took a day to break in but the torque and sound diff. is huge. so i thought i would share my experience for those contemplating the idea. well worth the the 549 without install. and thanks to forged for helping me out.

Any issue at all with hydrolock?

Modshack · 06-14-2009, 11:36 AM

Quote:

Originally Posted by 370NUTZ

Any issue at all with hydrolock?

I'm sorry, but I don't understand the continuing concern about this. The Stillen filters mount a good 24 inches off the road and are protected on the bottom by the large aluminum impact bar and a big hunk of stryrofoam. This is not at all like some of the 350 intakes where the filter hung down low in the grill and was susceptible to water ingestion. Unless you make it a habit of driving through 24" puddles I think this should be of no concern.. Even if you were to stuff the car into a 1 foot puddle and water caught on the lip, most would be directed at and through the radiator. The front side of the Stillens are so protected from even this splashing that you'll still pull air (no hydrolock)

kannibul · 06-14-2009, 02:53 PM

Just wondering, with this intake, and say a Stillen high-flow Cat and a cat-back setup...what kind of numbers would that put up?

NewlyIMPORTed · 06-14-2009, 03:02 PM

forged performance says with the full set up it should put 310 to the wheel

kannibul · 06-15-2009, 09:23 AM

Quote:

Originally Posted by NewlyIMPORTed

forged performance says with the full set up it should put 310 to the wheel

What is stock at the wheel?

NewlyIMPORTed · 06-15-2009, 09:27 AM

i think its like 258 or something

semtex · 06-15-2009, 12:31 PM

Depends on the dyno. 258 is about right for a Dyno Dynamics or Mustang Dyno.

jpit · 06-26-2009, 08:22 PM

New test of the Stillen G3:

Stillen?s Gen 3 Nissan 370Z Air Intake, Tested! > MotoIQ > Magazine Articles

06-12-2009, 10:55 PM	#31 (permalink)
ZforMe Base Member Join Date: Jan 2009 Location: Memphis TN Posts: 238 Drives: 370Z Sport Auto PG Rep Power: 16	Modshack, Would the idea be to finish fabricating and then develope a kit to sell to forum members (assuming everything works out well)? __________________ 13.369 @ 102.73 Bone Stock. BERK HFC's installed 5/14/09 @ 1490miles, 13.212 @ 106.15. Cobb Post MAF Hoses installed 3/20/10 @ 5,043miles, future: FI exhaust with 18" res and s/s cans.

06-15-2009, 12:31 PM	#39 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 32	Depends on the dyno. 258 is about right for a Dyno Dynamics or Mustang Dyno. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust	axio	Intake/Exhaust	82	07-31-2009 01:41 PM
Berk HFC and stillen Gen 3 intake	JonnieN	Intake/Exhaust	5	06-01-2009 03:26 PM
For sale Stillen G3 Intake	jpit	Parts for sale (Private Classifieds)	10	05-30-2009 10:31 AM
Stillen Dual Air Intake Kit.	doktor	Canada	8	05-21-2009 01:11 AM
Stillen Intake for VQ37VHR	vdcoff	Intake/Exhaust	7	01-25-2009 04:27 PM

06-14-2009, 02:53 PM	#35 (permalink)
kannibul A True Z Fanatic Join Date: Jun 2009 Location: Jenks, OK Posts: 2,281 Drives: 370z Touring/Sport Rep Power: 267	Just wondering, with this intake, and say a Stillen high-flow Cat and a cat-back setup...what kind of numbers would that put up?

06-14-2009, 03:02 PM	#36 (permalink)
NewlyIMPORTed A True Z Fanatic Join Date: May 2009 Location: Kennesaw, GA Posts: 1,109 Drives: 11 STI Sedan Rep Power: 18	forged performance says with the full set up it should put 310 to the wheel

06-15-2009, 09:27 AM	#38 (permalink)
NewlyIMPORTed A True Z Fanatic Join Date: May 2009 Location: Kennesaw, GA Posts: 1,109 Drives: 11 STI Sedan Rep Power: 18	i think its like 258 or something

06-26-2009, 08:22 PM	#40 (permalink)
jpit Enthusiast Member Join Date: Feb 2009 Location: Washington State Posts: 440 Drives: 370Z Tour MT w/Spt Rep Power: 16	New test of the Stillen G3: Stillen?s Gen 3 Nissan 370Z Air Intake, Tested! > MotoIQ > Magazine Articles