MOTORDYNE ART pipe NISMO--DYNO RESULTS!!

Footloose301 · 01-11-2012, 06:25 PM

Quote:

Originally Posted by sixpax

I am just trying to learn here, so put the flamethrowers aside for a moment.

I have been confused about how come stock and on the sticker when I bought the car it says 332 HP ... and then convos like these where a Z breaks the 300 mark with aftermarket bolt ons. I don't get it.

Cars lose power thru the drivetrain. All wheel drive cars lose even more. Our cars dyno like 250-260whp on a mustang dyno and 270-280 on a dynojet. The Nismo dynos 15-20whp more usually.

sixpax · 01-11-2012, 06:27 PM

Quote:

Originally Posted by scottIN

332 is at the crank. Dyno numbers are at the wheels. I dunno what the drivetrain loss numbers are on the manual & slushbox, but they're usually 15%-18% on most cars. You can always get crank numbers by pulling the engine and putting it on an engine dyno vs. a chassis dyno.

Cool thanks ... +1 for explaining and not burning.

sixpax · 01-11-2012, 06:28 PM

Quote:

Originally Posted by Footloose301

Cars lose power thru the drivetrain. All wheel drive cars lose even more. Our cars dyno like 250-260whp on a mustang dyno and 270-280 on a dynojet. The Nismo dynos 15-20whp more usually.

Thanks ... +1

Flyboy · 01-11-2012, 08:01 PM

Quote:

Originally Posted by b1adesofcha0s

Well with the tune you should have been able to remove the speed limiter.

I don't have a tune.

MACSIMIZER · 01-11-2012, 08:13 PM

I was also at this dyno day, my car put down 287hp with ARK cbe and K&N typoon, no tune. This was with the 7at in 4th gear, tried 5th on the 3rd pull but hit the speed limiter at 6800rpm. Made more torque in 5th so it probably would have made a little more power if I could have gotten that extra 700 rpms.

b1adesofcha0s · 01-11-2012, 08:35 PM

Quote:

Originally Posted by Flyboy

I don't have a tune.

My bad, I thought you were getting a dyno tune.

red6spd · 01-12-2012, 10:56 AM

Quote:

Originally Posted by Armonster

Situation 1: A single car dynos higher than other similar cars on the same dyno, same day.

Situation 2: A large number of cars all dyno substantially higher on a particular dyno than other similar cars across the country on similar dynos.

Unless I am misunderstanding your post, you seem to be presenting proof that your local dyno is miscalibrated.

Who is presenting situation 1? 10-20hp more then one SOME guys on this forum made are SUBSTANTIALLY higher?

Rooskey · 01-12-2012, 11:30 PM

Those numbers sound great and legit. I dynoed 310hp/256tq with berks hfc's, k&n typhoon and nst pulleys (Nismo model). So with the test pipes I can dig it. Great job op!

BigT · 01-23-2012, 10:41 PM

As far as I know, dynojets don't have calibrations. They are set the way they are from the day they are new. The only thing that comes to mind are the rollers might be a little worn. Outside of that, you have a few options: SAE correction, STD correction, and weather correction. There are no other modes or correction factors like on mustang and dyno dynamic dyno's.

01-11-2012, 08:13 PM	#20 (permalink)
MACSIMIZER Enthusiast Member Join Date: Feb 2011 Location: Pensacola FL Posts: 268 Drives: '10 370Z Rep Power: 18	I was also at this dyno day, my car put down 287hp with ARK cbe and K&N typoon, no tune. This was with the 7at in 4th gear, tried 5th on the 3rd pull but hit the speed limiter at 6800rpm. Made more torque in 5th so it probably would have made a little more power if I could have gotten that extra 700 rpms. cooldwt likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Tanabe y pipe vs motordyne y pipe help me choose please	zuperman 370	Intake/Exhaust	14	01-30-2012 11:48 PM
[FOR SALE] Motordyne Art Pipe v2 900 miles	kosstick	Parts for sale (Private Classifieds)	3	01-07-2012 12:31 PM
Motordyne ART pipe, but Cat is necessary..	someday	Intake/Exhaust	7	08-26-2011 01:35 AM
MOTORDYNE XYZ pipe	Kastley85891	Wanted	0	04-25-2011 06:31 AM
WTB: Motordyne XYZ pipe	GZ3	Wanted	2	03-14-2011 09:30 AM

01-12-2012, 11:30 PM	#23 (permalink)
Rooskey Track Member Join Date: Jul 2010 Location: South Carolina Posts: 974 Drives: 2014 Alpha7 GTR Rep Power: 16	Those numbers sound great and legit. I dynoed 310hp/256tq with berks hfc's, k&n typhoon and nst pulleys (Nismo model). So with the test pipes I can dig it. Great job op!

01-23-2012, 10:41 PM	#24 (permalink)
BigT Enthusiast Member Join Date: Jan 2012 Location: NJ Posts: 469 Drives: 98 2g DSM Rep Power: 13	As far as I know, dynojets don't have calibrations. They are set the way they are from the day they are new. The only thing that comes to mind are the rollers might be a little worn. Outside of that, you have a few options: SAE correction, STD correction, and weather correction. There are no other modes or correction factors like on mustang and dyno dynamic dyno's.