motordyne M370 mainfold installed and dyno tested

esfourteen

You guys want results, and I haven't had any coffee or food all day, so let's just cut right to it:

Install:
Takes about 1-2 hours, very simple, as expected.

The testing:

We did ONE baseline run before the install, which pretty much matched my previous runs when I got UpRev tuned at the same shop a few months back. We left the car on the dyno strapped down and installed the new manifold. We did 2 runs and then let the car cool down and did a final run, all runs we're datalogged using uprev to ensure things we're still in check. I've attached a dyno sheet comparing the baseline with the last run.

In the end, most people care about torque, and rightly so. There was a gain of about 8 peak tq, with similar gains throughout the midrange, but it just wasn't as good of results as Tony was seeing with the stock car he tested.

There was no average of 3 before or 3 after runs. I am not a shop owner and $125 in rebates for a dyno does not go a long way as I am sure most of you can imagine. I did call Tony after getting the results, and he offered to pay to have the stock manifold put back on and tested more, which was very cool but this was around 2:30 and they already had other cars to work on and I couldn't really stick around much longer.

With more runs and extensive testing, you might get better average #'s, but after seeing the car before and after, the loss of power/torque is there near redline, and it's not going to change with more pulls. Perhaps this is only apparent when mods/tuning are in the picture, I don't know as I am the only person with full bolt ons and uprev to have tested this thus far.

I emailed some raw numbers to Tony at motordyne so hopefully he can use that to get some average delta gains.

For those that care about the peak numbers: -9hp/+8tq

Driving impressions:
It's too early to tell much, I got to stretch its legs briefly and the low/midrange pull definitely felt good, better, nothing drastic but I did notice it.

I may have gotten the car up to about 120 (shush) in 4th near redline and the one thing I did notice was that it didn't feel like reaching the rev limiter. It felt more difficult to get it to redline, it just wasn't as easy as it was previously, 7300-7600 felt like it lasted a few seconds, where it should have been ready to go into 5th, that really surprised me, and kind of bothers me. Maybe it's not a big deal, you don't hang out around redline often, and you can just shift a bit earlier, but it still bothers me...

Would I buy it again:
I'm not 100% sure yet, the mid range numbers look good on paper, and seem noticeable but at $720 shipped its a hard pill to swallow to see such a large drop off in the last ~500 RPM's, which lets face it, we can visit often with this car, it was meant to be taken to redline. I need to do more butt dyno testing to really be sure.

Lastly, I would like to thank the guys over at Performance Motorsport, they new I was testing the motordyne manifold and worked out a deal with me so in the end (when I get the refund from Motordyne) I won't have paid for the dyno/install out of pocket, really great guys over there and they know their Nissans.

Attached Images

Scan.jpg (553.6 KB, 5182 views)

__________________
Build Thread | GTM TT Install Thread | Engine Build Thread

wishihadnav

thanks for the info!!..im sure it'll help us all make a more informed decision..

shabarivas

Nice - thanks for posting your results man - takes a lot to be brave enough to test the waters for us Z owners. Let us know what your long term impressions are.

GZ3

maybe you need a retune to pull more out of it?

__________________
09 GT-R
12' 370Z 7AT HANDED DOWN
12'+13' 5.0 SOLD

daisuke149

Man that a/f looks all crazy.....

GZ3

^^ didnt even look at that....i think retune is definatley in order

__________________
09 GT-R
12' 370Z 7AT HANDED DOWN
12'+13' 5.0 SOLD

esfourteen

They tried looking to see if they could tweak anything but theres nothing else can they can change. Yeah the a/f looks crazy but its fine, it's just not averaged to give you that flat line we're used to seeing, no clue why they didn't.

__________________
Build Thread | GTM TT Install Thread | Engine Build Thread

Z eliminator

What was the A/F readings. did they change.
My car has full bolt ons, I will have the manifold early next week.
My red line is 8100 rpm and my hp starts dropping of at 7300 rpm.

Z

__________________
12.343 @114.14 . 4.5 stroker motor is now being built. Dec 1 2015.

GZ3

i would e-mail uprev and have them send you a tune, they have done this with me in the past...or go to another tuner...the AF ratio should "try" to be as consistent as possible all through redline, thats just way to erratic. and it shouldnt in the 14af at WOT, you need new targets for the car to hit

__________________
09 GT-R
12' 370Z 7AT HANDED DOWN
12'+13' 5.0 SOLD

WarmAndSCSI

I dunno, but those are some nice gains under the curve. Definitely more gained than lost!

__________________

esfourteen

I appreciate the concern, the afr is fine, it's erratic because its not averaged, and it's in the 13's at wot. the shop that tuned my car has been tuning Z's for years with UpRev.

__________________
Build Thread | GTM TT Install Thread | Engine Build Thread

esfourteen

agreed, I hope more driving reinforces this.

__________________
Build Thread | GTM TT Install Thread | Engine Build Thread

TBSS2008

Do you think the new M370 mainfold is making the car run leaner? I see the avg AF at 14 and min at 13.2. 13.2 AF should be perfect for NA car at WOT.

__________________
2011 Black Corvette Grand Sport 6spd | NNP Daul Mode Exhaust
2008 Trail Blazer SS Black | SuperChips Tune
2009 370Z Black 7AT Touring Sport (TRADED)

WarmAndSCSI

I actually did some basic analysis on your dyno graph, and there is definitely more area under the "after" curve from 5100+ rpm than the "before" curve. About 0.7% more power overall.

__________________

esfourteen

there was a weird dip in the afr around 6300 after installing, they fixed that after but it made no gains

__________________
Build Thread | GTM TT Install Thread | Engine Build Thread