SES code P0171

Nitex · 03-25-2010, 03:35 PM

I posted over in the engine tech area but i figured i would put my findings over here in the Intake/Exhaust area.

I threw a CEL/SES (service engine soon) last weekend. My idle was hanging at 1.1k and would not go below. I took it to my mechanic today and had him run the code, which came out to be a P0171, which he said was a lean code. We looked at my gen 3s and couldn't visually see any areas suspect for vacuum leaks. We decided to just reset, and address the issue again if/when the CEL comes back on.

If anyone has had an issue with this code i would appreciate hearing about how you fixed the situation.

If anyone wants to hear what it sounds like here is the link to my youtube video, off topic but oh well! I still need to post my install pics and thoughts on the setup.

YouTube - 370z stillen exhaust w/stock cats VS HFC + drive

________________________________
Stillen CBE, Gen 3's and Berk HFC

Nitex · 03-26-2010, 09:48 AM

seriously no one has encountered this CEL code ?

Knives · 03-30-2010, 01:02 PM

I had a different code (PO300 error (cylinder misfire)), but the issue was the same. My idle wouldn't drop below 1.2k.

If you just installed the intake, I'd say give it a couple of days to give the ECU time to adjust to the increased airflow.
If it's been more than a couple of days already, then I'd say re-check the hoses and clamps again. There has to be a leak somewhere, even if you cant see it. Try running the engine and spraying soapy water around the hoses, it'll show you if something isn't air tight.

evse82 · 03-30-2010, 08:47 PM

Check for exhaust leaks around the cats too. Also make sure every hose is tightened properly again on the intakes and that the sensors are in firmly. I had a CEL for ages different code but also a Lean condition and ended up being an exhaust leak in the gaskets between the berk cats and the headers. (they were makeshift gaskets so ended up using the berk gaskets)

binto100 · 04-29-2010, 01:57 PM

Nitex -

Just sent you a pm that reads:

Are you still throwing the P0171 code? I've ordered the Stillen G3 and CBE but now I'm on the fence about the Berk HFCs. I like the sound and power of your Z but I don't want to run lean or flash the ECU at this time as the car is brand new.

I'd appreciate your thoughts. Thanks.

Bruce

efuseakay · 04-29-2010, 07:16 PM

Quote:

Originally Posted by binto100

Nitex -

Just sent you a pm that reads:

Are you still throwing the P0171 code? I've ordered the Stillen G3 and CBE but now I'm on the fence about the Berk HFCs. I like the sound and power of your Z but I don't want to run lean or flash the ECU at this time as the car is brand new.

I'd appreciate your thoughts. Thanks.

Bruce

With proper installation, you will be fine.

evse82 · 04-29-2010, 10:09 PM

Quote:

Originally Posted by efuseakay

With proper installation, you will be fine.

I agree, after mine was done properly, absolutely no CEL

chuckd05 · 04-29-2010, 11:46 PM

That high idle along with engine light happened to my car the following day after my tune. I did a pedal reset and it went away and hasnt come back since. Been about 3 weeks, however since the tune i feel like i throw the cel from the test pipes.. def annoying

however I am getting to be a pro with the ecu pedal reset sequence.

03-25-2010, 03:35 PM	#1 (permalink)
Nitex Track Member Join Date: Jan 2010 Location: Seattle Posts: 848 Drives: '13 GTI Stage 2 UNI Rep Power: 16	SES code P0171 I posted over in the engine tech area but i figured i would put my findings over here in the Intake/Exhaust area. I threw a CEL/SES (service engine soon) last weekend. My idle was hanging at 1.1k and would not go below. I took it to my mechanic today and had him run the code, which came out to be a P0171, which he said was a lean code. We looked at my gen 3s and couldn't visually see any areas suspect for vacuum leaks. We decided to just reset, and address the issue again if/when the CEL comes back on. If anyone has had an issue with this code i would appreciate hearing about how you fixed the situation. If anyone wants to hear what it sounds like here is the link to my youtube video, off topic but oh well! I still need to post my install pics and thoughts on the setup. YouTube - 370z stillen exhaust w/stock cats VS HFC + drive ________________________________ Stillen CBE, Gen 3's and Berk HFC

03-30-2010, 01:02 PM	#3 (permalink)
Knives Enthusiast Member Join Date: May 2009 Location: New York Posts: 293 Drives: 2009 370z 6MT Rep Power: 16	I had a different code (PO300 error (cylinder misfire)), but the issue was the same. My idle wouldn't drop below 1.2k. If you just installed the intake, I'd say give it a couple of days to give the ECU time to adjust to the increased airflow. If it's been more than a couple of days already, then I'd say re-check the hoses and clamps again. There has to be a leak somewhere, even if you cant see it. Try running the engine and spraying soapy water around the hoses, it'll show you if something isn't air tight. __________________ Mods list and pics Click

04-29-2010, 01:57 PM	#5 (permalink)
binto100 Base Member Join Date: Apr 2010 Location: Seattle Posts: 32 Drives: 2010 370Z Anniv M6 Rep Power: 15	Nitex - Just sent you a pm that reads: Are you still throwing the P0171 code? I've ordered the Stillen G3 and CBE but now I'm on the fence about the Berk HFCs. I like the sound and power of your Z but I don't want to run lean or flash the ECU at this time as the car is brand new. I'd appreciate your thoughts. Thanks. Bruce __________________ Stillen G3 intake, CBE, 19 row oil cooler and power steering oil cooler. VentureShield bumper, full hood.

04-29-2010, 11:46 PM	#8 (permalink)
chuckd05 A True Z Fanatic Join Date: Oct 2009 Location: NY Posts: 2,391 Drives: No longer a Z Rep Power: 20	That high idle along with engine light happened to my car the following day after my tune. I did a pedal reset and it went away and hasnt come back since. Been about 3 weeks, however since the tune i feel like i throw the cel from the test pipes.. def annoying however I am getting to be a pro with the ecu pedal reset sequence. __________________ 09 370Z 6M PW - FBO Best 1/4 mile = 12.926 @ 109 SOLD -- 08 BMW 135i - FBO 12.1@120mph SOLD -- white 09 e92 335 Coupe Mtech - 11.9 @ 119 :-)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CEL Code - P2A00	evse82	Intake/Exhaust	21	03-01-2012 06:53 PM
Code U1024	Megan370z	Tuning	9	03-15-2010 09:15 PM
How about this code reader?	Red370	Nissan 370Z General Discussions	16	01-05-2010 05:45 PM
Need Help - OBD code	jpit	Nissan 370Z General Discussions	11	11-03-2009 07:44 PM
gas cap and cel(SES) code	tru_Asiatik	Engine & Drivetrain	7	07-09-2009 12:38 PM

03-26-2010, 09:48 AM	#2 (permalink)
Nitex Track Member Join Date: Jan 2010 Location: Seattle Posts: 848 Drives: '13 GTI Stage 2 UNI Rep Power: 16	seriously no one has encountered this CEL code ?

03-30-2010, 08:47 PM	#4 (permalink)
evse82 Track Member Join Date: Nov 2008 Location: Melbourne, AUS Posts: 609 Drives: Black 370z MT Rep Power: 18	Check for exhaust leaks around the cats too. Also make sure every hose is tightened properly again on the intakes and that the sensors are in firmly. I had a CEL for ages different code but also a Lean condition and ended up being an exhaust leak in the gaskets between the berk cats and the headers. (they were makeshift gaskets so ended up using the berk gaskets)