Berk Cat-Back Exhaust GB #2!!!

phelan · 03-11-2010, 06:33 PM

Quote:

Originally Posted by ChrisSlicks

We order 75 lb computer UPS's on a regular basis. Probably almost 50% of these were getting damaged by UPS in transit. The UPS's aren't packed in the best packaging in the world, so if they get dropped from any height they break.

UPS doesn't use heavy equipment for handling packages unless it is freight (over 150 lbs). Anything over 70 lbs is supposed to be picked up by 2 people but that almost never happens. When the truck gets to the sorting facility the unloaders climb aboard and start slinging packages.

You ship UPS using UPS...wow that was confusing for a few seconds lol

ChrisSlicks · 03-11-2010, 06:50 PM

Quote:

Originally Posted by phelan

You ship UPS using UPS...wow that was confusing for a few seconds lol

Sorry, wasn't thinking about that when writing it, LOL.

cmmonte92 · 03-11-2010, 08:27 PM

Got the exhaust about an hour ago... No obvious damage to the packaging but was on my way into work and haven't opened it yet. I'll see how it looks inside when I get home, later tonight.

cab83_750 · 03-11-2010, 08:38 PM

How hard is it to 'unbend' the hanger? Can it just be bent so that the right and left hangers are at the same height?

The Weapon · 03-11-2010, 09:30 PM

Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes.
Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them.

dlmartin81 · 03-11-2010, 09:33 PM

^^ Actually, it looks like you got it to me.

g96818 · 03-11-2010, 11:55 PM

Quote:

Originally Posted by The Weapon

Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes.
Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them.

what did u do? adjust the hanger?

Minicobra1 · 03-12-2010, 05:14 AM

Here is an actual video of UPS unloading Berk exhaust off the docks.

B1nks · 03-12-2010, 07:35 AM

Quote:

Originally Posted by The Weapon

Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes.
Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them.

This is how mine bolted up only the driver side was a tad lower than the passenger.

370Zsteve · 03-12-2010, 08:44 AM

Quote:

Originally Posted by The Weapon

Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes.
Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them.

You license plate is crooked!

dlmartin81 · 03-12-2010, 09:26 AM

Quote:

Originally Posted by Minicobra1

Here is an actual video of UPS unloading Berk exhaust off the docks.

The Weapon · 03-12-2010, 09:51 AM

Quote:

Originally Posted by g96818

what did u do? adjust the hanger?

I turned it upside down and put a 2x4 wrapped in a towel to prop up the lower end and i stood on the tall end which in my case would have been the passenger side. It just bent ever so slowly. Then i got the same 2x4 and tried to raise the driver side up a bit.

That was the best i could do since i don't have any tools to properly bend it.

As for the lic. plate being crooked I did that on purpose to make an optical illusion that the exhausts weren't crooked.

370Zsteve · 03-12-2010, 10:11 AM

Quote:

Originally Posted by The Weapon

As for the lic. plate being crooked I did that on purpose to make an optical illusion that the exhausts weren't crooked.

Matt · 03-12-2010, 10:31 AM

Quote:

Originally Posted by The Weapon

As for the lic. plate being crooked I did that on purpose to make an optical illusion that the exhausts weren't crooked.

cab83_750 · 03-12-2010, 10:58 AM

Do you happen to know if the Berk exhaust is 'lower/higher" to the ground compared to stock? Do you happen to have a 'before' picture for comparison purposes?

Just need to know if scraping issues might occur.

Lastly, are the tips (both left and right) centered to the cutout? In looking at the picture, it appears that the side-to-side width of the left-and-right tips are a tad narrow.

Thanks.

Quote:

Originally Posted by The Weapon

Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes.
Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them.

03-11-2010, 08:27 PM	#243 (permalink)
cmmonte92 Base Member Join Date: Sep 2009 Location: Santa Clarita, CA Age: 50 Posts: 113 Drives: 09 135i Convertible Rep Power: 16	Got the exhaust about an hour ago... No obvious damage to the packaging but was on my way into work and haven't opened it yet. I'll see how it looks inside when I get home, later tonight. __________________ Mod's: Berk HFC's / Berk CBE / NISMO Suspension / JDM badge / Cobb AP Tune / ModShack Oil-cooler Parts on hand, but not installed: Rear Fog light / AIT NISMO Front Bumper Mod's wanted: Powder-Coated Stock-Sport Ray's / Sway Bars

03-11-2010, 09:30 PM	#245 (permalink)
The Weapon Enthusiast Member Join Date: Nov 2008 Location: Tucson, AZ Posts: 286 Drives: 370Z Tour/Sport Blk Rep Power: 3372	Berk is sending me a replacement for the back part to exchange but in the mean time they said i could keep the current one they shipped and try to tweak it myself. I almost fixed it 100% but it's still not quite there. It will do for now until my new rear section comes. Oh and this is without any other modifications. No nuts, no washers just bolted the way it's suppose to be. After i tried the "washers fix" I experienced a very annoying vibration and removed them. __________________ Boosted Performance Comp Turbo - Tuner- CJM Fuel Return- Modified Berk CBE- ZSpeed Stage 4 Clutch - Southbend Flywheel - Tuned by Seb ~650whp - HKS Coilovers - SPL - Focal Audio 4 way Active - Audiocontrol DSP - Work CR 2P

03-12-2010, 05:14 AM	#248 (permalink)
Minicobra1 A True Z Fanatic Join Date: Nov 2008 Location: Orange County, CA. Posts: 1,205 Drives: 370Z Tour, Spt, 6mt Rep Power: 645	Here is an actual video of UPS unloading Berk exhaust off the docks. __________________ 370z Tour\| Spt Pack\|Navi\|BERK CBE\|Berk HFC's\| Eibach Springs\| Hotchkis Sway Bars\|SPC Camber Arms\|15mm Ichiba Wheel Spacers\| 19"Factory Nismo Wheels-Matt Black\|Stop Tech Rotors\|TWM Shifter\|3M Tint\|Black Fangs\|Black Rear Valance\|JDM Fog Light\| MY BAND-www.myspace.com/petroleum

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DDMotorsports: Berk Technology Cat-Back Exhaust	M.Bonanni	Exhaust/Intake	47	12-14-2009 01:20 PM
Berk Technology Cat-Back Coming Soon!	M.Bonanni	Intake/Exhaust	468	08-14-2009 10:36 PM
Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust	axio	Intake/Exhaust	82	07-31-2009 01:41 PM

03-11-2010, 08:38 PM	#244 (permalink)
cab83_750 Track Member Join Date: Apr 2009 Location: CA Posts: 887 Drives: 09 NISSAN 370Z Rep Power: 417	How hard is it to 'unbend' the hanger? Can it just be bent so that the right and left hangers are at the same height?

03-11-2010, 09:33 PM	#246 (permalink)
dlmartin81 Track Member Join Date: Dec 2008 Location: Chalfont, PA Age: 43 Posts: 923 Drives: 09 370Z Rep Power: 608	^^ Actually, it looks like you got it to me.