Gauge selection

nomodsjk · 08-12-2014, 02:32 PM

Quote:

Originally Posted by aszyd

And it's expensive as hell! I was looking into the Greddy, but the cost and all the things you mentioned turned me off. If they had their new version out already, I might have considered it. But I'm not about to drop $500 to display oil temp and pres. on the same gauge, when it is the wrong size and already EOL. Instead, I spent 300 to do it with the two NEW Tanabe gauges.

That being said, if I ever went turbo, I could see using the Greddy for boost, IAT and EGT on the same gauge.

You are correct about the video display while the car is moving issue, but there are wiring hacks that can be done to prevent that problem.

I just bought the new tanabe gauges at R/T tuning yesterday and they are definitely the sexiest gauges on the market right now IMHO

aszyd · 08-12-2014, 02:43 PM

Quote:

Originally Posted by jwick

I wouldn't consider running any gauges NA. I researched all the options and the GReddy and Innovate were the best two pod combination option on the market. Everything else either left something to be desired or involved more pods. (item to note is I have a G and there are no pods on the dash and everyone has the display screen regardless if you have nav or not)

As for cost. It was about the same as any other setup combination I looked at assuming you buy good gauges, which is the only way to go when boosting. Why spending $10-15k and then cheap out for a couple hundred savings on gauges.

I'm with you on all of that. I have an oil cooler ready to go, but the general consensus was to not run one without a pressure gauge, so out came the stock gauges and in went aftermarket. I was hoping for a dual pressure / temp setup, but the only gauge that worked for me was the Greddy and I was ultimately unhappy with it. If it were 52mm and/or not EOL, my story would be different.

theDreamer · 08-12-2014, 02:45 PM

Are these the new Tanabe gauges you all are talking about: Tanabe USA Inc. - Revel VLS Gauges

aszyd · 08-12-2014, 03:42 PM

Yes. I have the oil pressure and temp. I am considering getting the AFR, since all three of the stock gauges have to be swapped.

Nixlimited · 08-12-2014, 04:56 PM

Quote:

Originally Posted by aszyd

Yes. I have the oil pressure and temp. I am considering getting the AFR, since all three of the stock gauges have to be swapped.

Those look pretty decent. So little innovation in the gauge arena! Looking forward to seeing what GaleForce comes up with.

nomodsjk · 08-12-2014, 09:09 PM

Quote:

Originally Posted by theDreamer

Are these the new Tanabe gauges you all are talking about: Tanabe USA Inc. - Revel VLS Gauges

Yes. They're amazing

Aviator44 · 08-13-2014, 07:49 PM

I'm looking into running the Defi Advance control unit. Off that, run a Advance ZD screen with oil pressure, oil temp, and fuel pressure. Then in the 3 dash spots, run a Defi Boost gauge off the ACU, then two stand alone widebands.

ACU
ADVANCE Control Unit Summary | Defi - Exciting products by NS Japan

ZD Display
ADVANCE ZD Summary | Defi - Exciting products by NS Japan

whiteZ34 · 08-14-2014, 01:39 AM

Quote:

Originally Posted by jwick

Did you buy JoePro's kit?

Yes, I had purchased his kit and I'm currently installing it myself along with my father on jack stands in my garage haha. Proving it can be done

jwick · 08-14-2014, 06:50 AM

Quote:

Originally Posted by whiteZ34

Yes, I had purchased his kit and I'm currently installing it myself along with my father on jack stands in my garage haha. Proving it can be done

Welcome to the BP club brother!

And most of us installed it in our garages, so it can definitely be done. Any questions, hit us up. We are more than willing to assist.

GaleForce · 08-14-2014, 09:34 AM

Quote:

Originally Posted by whiteZ34

Yes, I had purchased his kit and I'm currently installing it myself along with my father on jack stands in my garage haha. Proving it can be done

Quote:

Originally Posted by jwick

Welcome to the BP club brother!

And most of us installed it in our garages, so it can definitely be done. Any questions, hit us up. We are more than willing to assist.

Yep, I was the first to DIY the Boosted Performance kit, and on jack stands. Easy. I think most of the BP kits have been DIY'd, so there is a lot of experience on the forum. Like jwick said, if you run into any snags, hit us up.

GaleForce · 08-14-2014, 09:39 AM

Back on topic, for those who want multi gauges and can afford the room for a screen, this is a sample of what I'm looking at.

It's fully customizable, the above is a sample layout. You can display more sensor readings on other "pages". I'm also looking into having this work with the factory Nav screen.

theDreamer · 08-14-2014, 09:43 AM

Quote:

Originally Posted by GaleForce

Back on topic, for those who want multi gauges and can afford the room for a screen, this is a sample of what I'm looking at.

It's fully customizable, the above is a sample layout. You can display more sensor readings on other "pages". I'm also looking into having this work with the factory Nav screen.

So what is the back bone running this setup (raspberry pi)? I would assume OBD2 connection and then extra connections for boost and pressures?

GaleForce · 08-14-2014, 09:53 AM

Quote:

Originally Posted by theDreamer

So what is the back bone running this setup (raspberry pi)? I would assume OBD2 connection and then extra connections for boost and pressures?

No OBDII, sending units for whatever you want to monitor.

Here is some more info,

The gauge makes use of a joystick to enable the user to swap between the different modes and readings. It even could be programmed for you to hold the peak values for each reading.

Do you want to be notified if you exceed a maximum or go lower than a minimum reading? You can have your gauge with an LED to warn you in such situations.

The most important feature of this LCD is that it can be customised to any look by the user. Peak values can be set to whatever the users desire within the settings menu. LED warning light can be turned on or off. Within the settings menus, the user can choose which readings to be shown in the gauge mode in case the sensor is not available at the time, either not present or getting changed.

Do you want to use your multi gauge also to control your car components as well as monitor? Then this unit can be programmed to keep an eye on temperatures to start your radiator fan on low speed or high speed! Very useful when on track days.

nomodsjk · 08-14-2014, 10:00 AM

Quote:

Originally Posted by GaleForce

Back on topic, for those who want multi gauges and can afford the room for a screen, this is a sample of what I'm looking at.

It's fully customizable, the above is a sample layout. You can display more sensor readings on other "pages". I'm also looking into having this work with the factory Nav screen.

You get that to work with the nav screen then put me on the list. That's a must have!

Nixlimited · 08-14-2014, 10:43 AM

Yep, factory nav screen is what I want. And OBDII would be amazing because it would save me the cost of many sender units.

08-12-2014, 02:45 PM	#18 (permalink)
theDreamer A True Z Fanatic Join Date: Feb 2009 Location: Texas Posts: 30,879 Drives: 370z Rep Power: 4210	Are these the new Tanabe gauges you all are talking about: Tanabe USA Inc. - Revel VLS Gauges Rusty likes this. __________________ theDreamer's Z // Fast Intentions // Uprev // GTM // HKS // TEIN theDreamer's Silvia // URAS // GREDDY Houston Zs // Facebook // Twitter // Instagram

08-12-2014, 03:42 PM	#19 (permalink)
aszyd Track Member Join Date: May 2014 Location: Florida Posts: 877 Drives: Magma Red 370z T+S Rep Power: 21	Yes. I have the oil pressure and temp. I am considering getting the AFR, since all three of the stock gauges have to be swapped. __________________ Competition Clutch\|Fast Intentions\|Maxbore\|NST\|Setrab\|Stillen\|Tomei\|Uprev\| Z1 Avant Garde\|SPC\|Stance\|Whiteline Aerojacket\|Seibon\|Tanabe\|TRS\|TWM

08-13-2014, 07:49 PM	#22 (permalink)
Aviator44 Enthusiast Member Join Date: May 2014 Location: Pensacola, FL Posts: 299 Drives: AAM Twin Turbo 370Z Rep Power: 11	I'm looking into running the Defi Advance control unit. Off that, run a Advance ZD screen with oil pressure, oil temp, and fuel pressure. Then in the 3 dash spots, run a Defi Boost gauge off the ACU, then two stand alone widebands. ACU ADVANCE Control Unit Summary \| Defi - Exciting products by NS Japan ZD Display ADVANCE ZD Summary \| Defi - Exciting products by NS Japan nomodsjk likes this. __________________ www.aamcompetition.com AAM Twin Turbo System

08-14-2014, 09:39 AM	#26 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51865	Back on topic, for those who want multi gauges and can afford the room for a screen, this is a sample of what I'm looking at. It's fully customizable, the above is a sample layout. You can display more sensor readings on other "pages". I'm also looking into having this work with the factory Nav screen. wheee! and nomodsjk like this. __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

08-14-2014, 10:43 AM	#30 (permalink)
Nixlimited A True Z Fanatic Join Date: Aug 2009 Location: San Diego Posts: 1,235 Drives: 15 GT-R / 11 Prius Rep Power: 26	Yep, factory nav screen is what I want. And OBDII would be amazing because it would save me the cost of many sender units. __________________ Car Sold! Pleasure being a part of the Z community. New ride: 2015 GT-R - 647 WHP / 641 WTQ (e85) & 543 WHP / 519 WTQ (91)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Gauge selection for a twin-turbo 370z?	Nuc370z	Forced Induction	3	05-04-2014 12:59 AM
Summer Tire Selection	fuzzywuzzy	Wheels & Tires	21	01-07-2011 11:29 AM
Need help on selection of motor oil	kyung88	Engine & Drivetrain	49	11-17-2010 07:38 PM
Clutch selection	Seth G	Engine & Drivetrain	0	03-15-2010 08:33 PM
What happened to the tire pressure gauge and speedo in the middle gauge cluster?	rbratton	Nissan 370Z General Discussions	33	01-24-2009 11:28 PM