So just ordered my Stillen SC

mikey1600

Hey Mark,

just went to send you a PM, and it's saying your mailbox is full, I'll try again soon, just sending my email address through.

Cheers!

mikey1600

Hey guys,

does anyone have a print-out of the 370z fuse box wiring diagram? mines got different coloured wires in different positions then where it says in the stillen manual.........

Team_STILLEN

Do you have a Multi-Meter? All you need to do is find a wiring coming out of the fuse box that is at 12v when the car is in ACC mode and 0V when the car is off. This activates the relay to allow the voltage from the battery connection to flow and run the water pump for the IC when the car is on.

__________________
Financing with Affirm now available!!!

STILLEN | Robin | Performance Specialist | rmoses@stillen.com| 800.576.2131 x133 |

jwick

if per Stillen below all you are looking for is switched 12v power just tap into either cigarette lighter locations. I did mine with an add a fuse. both are located in the kick panel left of the clutch/brake pedal.

__________________
'10 G37T 6MT Graphite/Graphite - BP - G37T Build

mikey1600

Ended up finding it thanks mate,

just in the manual it shows a yellow wire, and there are 2 yellow wires in there on my car, yet they are in different positions, ended up using the same position wire which was a green one, it had power when in ON position (not car started, just ON, as if hitting power button twice without foot on clutch) not ACC, didn't want the pump running on ACC if I'm working on car in garage and have radio on/waiting in a car park with radio on.

the only other thing which was a bit weird was the purge valve, in the manual it shows the manifold without the hose fitting between the 2 throttle bodies, I had 1 hose which was left over which runs with the fuel line and has a little grey filter looking thing on it (I'll upload it to my profile), I've connected this to the purge valve on one of the T piece-ends and connected a hose from the other T piece-end to the middle hose connection on the manifold, hope this is correct, in the manual it shows just 1 connection from the purge valve, all the other hoses in my engine bay are allocated, this was the only one left over and thought it went here, can anyone clarify to make sure I haven't done something wrong?

will be complete tomorrow and starting it up, just need to install the charge pipe now and load the map!

still have a few pieces to tidy up and test fit the front bar etc.. so will still be a full day, my tunes booked for Monday, excited!

mikey1600

this is the piece I'm talking about - Nissan 370Z Forum - mikey1600's Album: My 370z + upgrades - Picture

mikey1600

found a picture on a stock motor, one end goes into the purge valve, then a small hose goes from the other end of the purge valve into the standard manifold, so the way I've set it up should be fine

mikey1600

Hey guys, need a quick question answered, I've posted the question here - HELP loading stillen tune file via UpRev

mikey1600

all loaded, starts first time perfectly, no leaks etc.. going for quick drive around block soon, modifying front bar to fit..

Mr&Mrs

Congrats dont have too much fun till you get her to your tuner!

__________________
Project Z <--Click - Check out the link too many mods to list!

Z&I

Good Work Dude !!!

__________________
.
BB

mikey1600

haha no way mate, just drove down the servo to get some fuel, kept it under 3000rpm, very hard to do! lol

Team_STILLEN

Congrats on getting her finished Mikey! Let us know how the tuning goes!

__________________
Financing with Affirm now available!!!

STILLEN | Robin | Performance Specialist | rmoses@stillen.com| 800.576.2131 x133 |

JWillis72

Congratulations! When does it get tuned?


Sent from my iPhone using Tapatalk

mikey1600

Thanks! will do

getting tuned tomorrow (in about 14 hours!) going to be hard getting to sleep tonight, very excited!