Boosted Performance V 2.0

whiteZ34 · 10-26-2015, 02:37 AM

Quote:

Originally Posted by Boosted Performance

BTW, the difference between V 1.0, 1.5 and 2.0 can be found in the first post of this thread.

Hey Sasha, I need you to email/message me please sir.

iBenJAMM1N · 10-26-2015, 11:36 PM

Quote:

Originally Posted by Boosted Performance

I have 4 V 1.5 TUNER kits that I am finishing up, and need gone.

These are going at a decent discount of: $5,900 to your door, but do not include an oil cooler kit. So it is a great solution for those that may have a supercharger and wish to upgrade to a turbo kit, or for those that may already have an oil cooler kit and are on a N/A tune.

I can turn these in to a complete turn key kit, which would include UpRev, 750cc fuel injectors, and fuel pump. That would add about $1,050 to the price. This still does not include an oil cooler.

This kit as is, can easily make 600whp on a built engine.

There are two choices for down pipe...Fast Intentions or OEM. For open dump tubes, there is another $150 discount.

Please let me know if you are interested, and I can take deposits. These would ship in about 4 weeks after the deposits have been received.

what is the " fast intention or oem down pipe"?

Boosted Performance · 10-27-2015, 12:30 AM

Quote:

Originally Posted by iBenJAMM1N

what is the " fast intention or oem down pipe"?

It is the downstream section of the exhaust system. It will bolt up to either the OEM exhaust, or any after market exhaust system that would bolt up to the OEM Y-pipe. I also have the option for a down pipe that will bolt up to the Fast Intensions dual 2.5" exhaust, as well as the Motordyne exhaust.

jwick · 10-27-2015, 08:55 AM

Just to note. If you are buying for a G only the OEM exhaust option works. The FI mod-pope connection is in a different location than on a G. I cannot speak for the Motordyne.

Boosted Performance · 10-27-2015, 09:54 AM

Quote:

Originally Posted by jwick

Just to note. If you are buying for a G only the OEM exhaust option works. The FI mod-pope connection is in a different location than on a G. I cannot speak for the Motordyne.

Oh, thanks for the input on that.

jwick · 10-27-2015, 09:56 AM

Quote:

Originally Posted by Boosted Performance

Oh, thanks for the input on that.

Any time. And I should probably expand on that. Any exhaust that uses the OEM flange location will work (i.e. I originally had a Stillen exhaust and it mated just fine)

iBenJAMM1N · 10-27-2015, 12:01 PM

Quote:

Originally Posted by Boosted Performance

It is the downstream section of the exhaust system. It will bolt up to either the OEM exhaust, or any after market exhaust system that would bolt up to the OEM Y-pipe. I also have the option for a down pipe that will bolt up to the Fast Intensions dual 2.5" exhaust, as well as the Motordyne exhaust.

I figured that's what it was, but then again, just to clarify

PongSanity · 10-29-2015, 11:05 AM

my downpipe would be oem and hopefully it matches up to the Ark exhaust fairly well. I already spoke to a welder and he's already excited to get this build started.

6mt370 · 11-08-2015, 02:32 AM

Hey guys, started installing my BP kit today and I have a few questions. First one is, how the hell do you get the oil pan separated from the engine? I was using any tool I could find to wedge in there and nothing. I'm baffled at how to get it off. I'm using the large cast area to pry against but it's chipping away at it and I don't want to ruin that!

Second, I installed the exa pump and clipped on the harness with the black and red wore attached only. Now, I'm left with two harnesses, both with several wires and one has the add a fuse attached to it. Confused on how to wire that or where to even install it because both my red and black wires are right next to the fuse box already ( haven't wired anything yet just ran those two wires over to the location)

Those are the two harnesses. Really stuck on what to do there. Any help is appreciated. The exhaust is off and some of the oil lines are installed so only a few more days of work and I should be good

mag_black · 11-08-2015, 08:14 AM

Are you trying to pry it off w/ just one bolt removed?

edit: not trying to be a smartass about it.

YzGyz · 11-08-2015, 09:54 AM

The oil pan needs a good bit of prying to get off. Take all the bolts off. Then use a flat bar ( one that is shaped like an "L") and stick the shorter end between the pan and block. Give it a few good wings with the hammer till it works itself in. Use a second pry bar or big long screwdriver to work your way around loosening the pan. The pan will be warped a little in the pry area but you can beat it strait again with a flat surface and a socket or something.

As for the two wire harness, one is for the Exa, one is for the fuel pump.

I think I have pics somewhere in my build thread.

YzGyz

YzGyz · 11-08-2015, 09:59 AM

YzGyz's turn!

Here you go.

YzGyz

jwick · 11-08-2015, 10:15 AM

Quote:

Originally Posted by 6mt370

Hey guys, started installing my BP kit today and I have a few questions. First one is, how the hell do you get the oil pan separated from the engine? I was using any tool I could find to wedge in there and nothing. I'm baffled at how to get it off. I'm using the large cast area to pry against but it's chipping away at it and I don't want to ruin that!

Second, I installed the exa pump and clipped on the harness with the black and red wore attached only. Now, I'm left with two harnesses, both with several wires and one has the add a fuse attached to it. Confused on how to wire that or where to even install it because both my red and black wires are right next to the fuse box already ( haven't wired anything yet just ran those two wires over to the location)

Those are the two harnesses. Really stuck on what to do there. Any help is appreciated. The exhaust is off and some of the oil lines are installed so only a few more days of work and I should be good

The relay with the add a fuse is for the Exa pump and the other is for the factory fuel pump harness. There's a pretty crude Microsoft paint sketch that shows how to wire the fuel pump harness. If I recall properly you cut the pink wire in the factory fuel pump harness but I can't remember which end of the harness gets spliced to each side of the cut pink wire.

I agree with the others. Take all the pan bolts out completely before you start trying to pry it off. I stuck a flathead screw driver in the seam and hit it with a hammer a few times. Once I got it started I basically repeated the process with a second flathead until it was open enough for me to work my way around. You will have to reshape the pan a little once you get it off.

There's a lot of detail in my build thread if you need reference. Clink the link in my signature.

jwick · 11-08-2015, 10:32 AM

Found it

NeverBoneStck · 11-08-2015, 01:54 PM

From that pic it looks like the pan is still bolted to the block. If you tried to take the oil pan off like that you should not be installing the turbo kit. Stop now!!!

Quote:

Originally Posted by 6mt370

Hey guys, started installing my BP kit today and I have a few questions. First one is, how the hell do you get the oil pan separated from the engine? I was using any tool I could find to wedge in there and nothing. I'm baffled at how to get it off. I'm using the large cast area to pry against but it's chipping away at it and I don't want to ruin that!

Second, I installed the exa pump and clipped on the harness with the black and red wore attached only. Now, I'm left with two harnesses, both with several wires and one has the add a fuse attached to it. Confused on how to wire that or where to even install it because both my red and black wires are right next to the fuse box already ( haven't wired anything yet just ran those two wires over to the location)

Those are the two harnesses. Really stuck on what to do there. Any help is appreciated. The exhaust is off and some of the oil lines are installed so only a few more days of work and I should be good

10-27-2015, 08:55 AM	#304 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	Just to note. If you are buying for a G only the OEM exhaust option works. The FI mod-pope connection is in a different location than on a G. I cannot speak for the Motordyne. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

11-08-2015, 08:14 AM	#310 (permalink)
mag_black A True Z Fanatic Join Date: Mar 2013 Location: Massachusetts Posts: 1,400 Drives: 09 370Z MT6 Rep Power: 666	Are you trying to pry it off w/ just one bolt removed? edit: not trying to be a smartass about it. 6mt370 and TheWeez like this. __________________ fujimura ≠ abbeyRoadCompany ≠ fastIntentions ≠ motordyne ≠ avantGarde ≠ ecutek ≠ nismo ≠ stillen ≠ stoptech ≠ gtm ≠ spl ≠ carbonfiberelement ≠ stance™

11-08-2015, 09:54 AM	#311 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 63	The oil pan needs a good bit of prying to get off. Take all the bolts off. Then use a flat bar ( one that is shaped like an "L") and stick the shorter end between the pan and block. Give it a few good wings with the hammer till it works itself in. Use a second pry bar or big long screwdriver to work your way around loosening the pan. The pan will be warped a little in the pry area but you can beat it strait again with a flat surface and a socket or something. As for the two wire harness, one is for the Exa, one is for the fuel pump. I think I have pics somewhere in my build thread. YzGyz 6mt370 likes this. __________________ http://www.the370z.com/members-370z-...gyzs-turn.html YzGyz

11-08-2015, 09:59 AM	#312 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 63	YzGyz's turn! Here you go. YzGyz __________________ http://www.the370z.com/members-370z-...gyzs-turn.html YzGyz

11-08-2015, 10:32 AM	#314 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	Found it __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

10-29-2015, 11:05 AM	#308 (permalink)
PongSanity Enthusiast Member Join Date: Jul 2014 Location: Virgin Islands Posts: 261 Drives: '09 G37s KH3 6MT Rep Power: 11	my downpipe would be oem and hopefully it matches up to the Ark exhaust fairly well. I already spoke to a welder and he's already excited to get this build started.

11-08-2015, 02:32 AM	#309 (permalink)
6mt370 Base Member Join Date: May 2015 Location: House Posts: 207 Drives: 370 Rep Power: 10	Hey guys, started installing my BP kit today and I have a few questions. First one is, how the hell do you get the oil pan separated from the engine? I was using any tool I could find to wedge in there and nothing. I'm baffled at how to get it off. I'm using the large cast area to pry against but it's chipping away at it and I don't want to ruin that! Second, I installed the exa pump and clipped on the harness with the black and red wore attached only. Now, I'm left with two harnesses, both with several wires and one has the add a fuse attached to it. Confused on how to wire that or where to even install it because both my red and black wires are right next to the fuse box already ( haven't wired anything yet just ran those two wires over to the location) Those are the two harnesses. Really stuck on what to do there. Any help is appreciated. The exhaust is off and some of the oil lines are installed so only a few more days of work and I should be good

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance turbo kit self install (review)	Cell	Forced Induction	87	10-24-2017 10:38 AM
Boosted Performance round 2 list	Boosted Performance	Forced Induction	1480	06-03-2014 09:44 AM
Joepro's Boosted Performance build thread!	Joepro	Member's 370Z Gallery	82	04-16-2014 12:09 PM
For you guys that want to know what the Boosted Performance kit sounds like :)	Mitco39	Nissan 370Z Photos / Spyshots / Video / Media Gallery	5	04-10-2013 02:26 PM