Boosted Performance V 2.0

jwick · 01-14-2015, 07:46 AM

Quote:

Originally Posted by Merv

Damn this is tempting!

Hey Sasha,how far can the torque be dialed down when pushing about 450 horse? I only ask because I would be Leary of running on stock internals and wouldn't be able to afford a rebuild.

I'd be shocked you could turn down the timing enough to get below 400-425wtq. Too little timing is just as bad as too much

victorofhavoc · 01-14-2015, 09:48 AM

Quote:

Originally Posted by Merv

Damn this is tempting!
Hey Sasha,how far can the torque be dialed down when pushing about 450 horse? I only ask because I would be Leary of running on stock internals and wouldn't be able to afford a rebuild.

From what I've seen of people on this forum so far I wouldn't be worried about running 450 WHP on stock internals. There was one guy who beats on his car and had 570 whp for around 20k miles, and then upped it to 671, and the only issue he had was the CSC (which people have had stock)

TopgunZ · 01-14-2015, 10:16 AM

Set it at 8psi and don't worry, be happy. And you will be. If it lets go at that psi level then it wasn't because of too much power.

jwick · 01-14-2015, 10:31 AM

Quote:

Originally Posted by TopgunZ

Set it at 8psi and don't worry, be happy. And you will be. If it lets go at that psi level then it wasn't because of too much power.

I would say use the 0.5bar spring in the WG and with a proper tune. Set it and be happy

TopgunZ · 01-14-2015, 11:10 AM

Can a guy use RTV on the header flange to xpipe to ensure a good seal? I can't get the berk gaskets as they are on backorder and have been since the beginning of December. I was thinking of using my old ones with a little RTV or the ultra copper permatex.

Is there a problem with this?

jwick · 01-14-2015, 11:24 AM

Quote:

Originally Posted by TopgunZ

Can a guy use RTV on the header flange to xpipe to ensure a good seal? I can't get the berk gaskets as they are on backorder and have been since the beginning of December. I was thinking of using my old ones with a little RTV or the ultra copper permatex.

Is there a problem with this?

I would just use RTV. Don't combine the two together.

Merv · 01-15-2015, 02:58 AM

Thanks for the info guys.

YzGyz · 01-15-2015, 03:35 AM

Should I crack the 2 triangle flanges that goes to the cat loose right now? The transmission is down and out of the way. I don't think I will every get as open of an angle to crack them loose as now. Me thinking yes, as I have already sprayed pb on them. Pic #10 on Shasha's original post on page 1. I need to stop by Harbor F and pick up a torque set and a darn 1/2 pneumatic impact gun. Stupid torques bolts are stuck.

YzGyz

jwick · 01-15-2015, 07:46 AM

Quote:

Originally Posted by YzGyz

Should I crack the 2 triangle flanges that goes to the cat loose right now? The transmission is down and out of the way. I don't think I will every get as open of an angle to crack them loose as now. Me thinking yes, as I have already sprayed pb on them. Pic #10 on Shasha's original post on page 1. I need to stop by Harbor F and pick up a torque set and a darn 1/2 pneumatic impact gun. Stupid torques bolts are stuck.

YzGyz

Unless you are willing to drive around with an exhaust leak until you do the kit install, I wouldn't touch the cat flange bolts

Gajewski · 01-15-2015, 08:39 AM

Quote:

Originally Posted by YzGyz

Should I crack the 2 triangle flanges that goes to the cat loose right now? The transmission is down and out of the way. I don't think I will every get as open of an angle to crack them loose as now. Me thinking yes, as I have already sprayed pb on them. Pic #10 on Shasha's original post on page 1. I need to stop by Harbor F and pick up a torque set and a darn 1/2 pneumatic impact gun. Stupid torques bolts are stuck.

YzGyz

-I would recommend getting a 1/2 inch breaker bar + cheater bar. You virtually have to break those bolts to remove them. My attempts with an impact were disappointing to say the least. The top one, especially, is a pain and needs a collection of extensions. I used a 4 ft. bar and had to hang on it.

I agree with jwick as well - exhaust leak is imminent if you break them off now and intend to drive the car.

Chuck33079 · 01-15-2015, 08:41 AM

Quote:

Originally Posted by jwick

Unless you are willing to drive around with an exhaust leak until you do the kit install, I wouldn't touch the cat flange bolts

Maybe crack them loose and retighten to the appropriate torque spec so it's easier to remove later? Of course, you're boned if you snap one off.

jwick · 01-15-2015, 08:46 AM

Quote:

Originally Posted by Chuck33079

Maybe crack them loose and retighten to the appropriate torque spec so it's easier to remove later? Of course, you're boned if you snap one off.

You know it's going to snap. I've busted off four demon bolts and I'm 4for4.

TopgunZ · 01-15-2015, 09:33 AM

I PB blasted them and let them sit overnight. Then they came off the next day with just a driver and short cheater bar. None broke.

If it were me I'd take them off when the tranny was out of the way. Let the car sit like that until you complete the install. There are a hundred other things to do before you get the rest of the parts if that is your holdup.

Guess you need a backup rig for this though, which you should if you go FI on the Z anyway.

YzGyz · 01-15-2015, 11:57 AM

Leave it alone it is. I still need to dd my car. What a shame. a perfect chance at them gone.

Thanks

SlowZ · 01-15-2015, 08:46 PM

I got them off a Z with 50k+ miles with one turn. I was lucky. Same with my Z and it had 33k. PB blast them though at least before you try. Use a 1/2 and like others said a cheater pipe works wonders.

01-14-2015, 10:16 AM	#273 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Set it at 8psi and don't worry, be happy. And you will be. If it lets go at that psi level then it wasn't because of too much power. Merv likes this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-14-2015, 11:10 AM	#275 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Can a guy use RTV on the header flange to xpipe to ensure a good seal? I can't get the berk gaskets as they are on backorder and have been since the beginning of December. I was thinking of using my old ones with a little RTV or the ultra copper permatex. Is there a problem with this? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM Last edited by TopgunZ; 01-14-2015 at 11:20 AM.

01-15-2015, 02:58 AM	#277 (permalink)
Merv Track Member Join Date: Dec 2013 Location: Vancouver B.C Posts: 518 Drives: 11 GM grey sport tou Rep Power: 14	Thanks for the info guys. __________________ Swift springs \| upgraded headlights \| stillen gen3 cai \| FI HFC's and FI CBE \| ecutek tune in the mail!

01-15-2015, 09:33 AM	#283 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	I PB blasted them and let them sit overnight. Then they came off the next day with just a driver and short cheater bar. None broke. If it were me I'd take them off when the tranny was out of the way. Let the car sit like that until you complete the install. There are a hundred other things to do before you get the rest of the parts if that is your holdup. Guess you need a backup rig for this though, which you should if you go FI on the Z anyway. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance turbo kit self install (review)	Cell	Forced Induction	87	10-24-2017 10:38 AM
Boosted Performance round 2 list	Boosted Performance	Forced Induction	1480	06-03-2014 09:44 AM
Joepro's Boosted Performance build thread!	Joepro	Member's 370Z Gallery	82	04-16-2014 12:09 PM
For you guys that want to know what the Boosted Performance kit sounds like :)	Mitco39	Nissan 370Z Photos / Spyshots / Video / Media Gallery	5	04-10-2013 02:26 PM

01-15-2015, 03:35 AM	#278 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 63	Should I crack the 2 triangle flanges that goes to the cat loose right now? The transmission is down and out of the way. I don't think I will every get as open of an angle to crack them loose as now. Me thinking yes, as I have already sprayed pb on them. Pic #10 on Shasha's original post on page 1. I need to stop by Harbor F and pick up a torque set and a darn 1/2 pneumatic impact gun. Stupid torques bolts are stuck. YzGyz

01-15-2015, 11:57 AM	#284 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 63	Leave it alone it is. I still need to dd my car. What a shame. a perfect chance at them gone. Thanks

01-15-2015, 08:46 PM	#285 (permalink)
SlowZ Premium Member Join Date: Jan 2014 Location: So cal Posts: 371 Drives: Z Rep Power: 11	I got them off a Z with 50k+ miles with one turn. I was lucky. Same with my Z and it had 33k. PB blast them though at least before you try. Use a 1/2 and like others said a cheater pipe works wonders.