Croydon Racing Developments Stillen Custom Tune

JWillis72 · 06-26-2014, 08:03 PM

Quote:

Originally Posted by Pro4Jackster

Stillen's setup on the other hand, unless I'm mistaken, reads temperature from before the supercharger, intercooler, and meth nozzles. So the car actually has no idea what IATs are by the time the air gets to the motor. Moving the sensor into the IM would be a big step forward for the Stillen supercharger.

That's correct, they are in the front bumper before the supercharger.

future370zzz · 06-26-2014, 10:22 PM

I have an sensor added after the MAF sensor and just before the intercooler. I see temperature of around 140 F when it's warmed up, in 75 F ambient weather. Unfortunately didn't install a sensor after the intercooler just before it enters the engine. Aghhhh

That will be the next step depending on how much it would cost now to add a sensor after everything has been installed. The gauge and sensor install alone was $1K.

tsui_san · 06-27-2014, 12:57 PM

Quote:

Originally Posted by ANMVQ

I don't think he has temp number pre heat exchanger but the key is when he says"My tuner could repeat same numbers during all 15 dyno runs without cool down " The Stillen one you'll get two runs the MAX before it gets heat soaked. I remember when I went to the track pre heat exchanger ( Was only 8 cars there with me) after my first two runs the car ran SLOW, I was so heat soaked I could actually feel the car lose power on the runs after, I would have to let it sit with the hood open for a good 10-15 mins after each run to cool off. The stock exchanger and location is not smart :/

That's good to know. On the 07-08 G sedan HR motor my A2W intercooler is different from the VHR ones...instead of a small square heat exchanger I actually have a long FMIC similar to the one being discussed. The only difference I see is that that IC is thicker (3" vs 1"+) and that the inlet/outlet are on the same side (Stillen inlet/outlet are on different ends). Not sure at this point if it's a worthwhile upgrade for me or if there's even an apples to apples comparison here.

vlad370z · 07-10-2014, 05:48 AM

Quote:

Originally Posted by tsui_san

do you have the dyno data pre-frozen boost install? Did you see any kw/n-m (metric system lol) gains?

below dyno results pre frozen boost heat exchanger and after. The tuner said previously he had to let it cool down before another dyno run, with the larger heat exchanger he could do run after run.

fuct · 07-10-2014, 08:59 AM

arnt we supposed to do dyno pulls in 5th? charts say 4th...... no?

ANMVQ · 07-10-2014, 11:22 AM

Not sure about the manuals but the 7 spd autos are 4th.

DEpointfive0 · 09-04-2014, 11:20 AM

Quote:

Originally Posted by ANMVQ

Not sure about the manuals but the 7 spd autos are 4th.

Its 5th for the 7AT and the 6MT

1slow370 · 09-04-2014, 12:26 PM

A lot of tuning passes are done in 4th to reduce load and keep the car from hitting the limiter, the final hp numbers run should be done in 5th.

ANMVQ · 09-04-2014, 12:45 PM

Quote:

Originally Posted by DEpointfive0

Its 5th for the 7AT and the 6MT

never had one done in 5th nor heard of one ? Not saying your wrong just the 6-8 dynos I've done have all been in 4th. isn't there some with the speed limiter on the dyno's 5th gear would be pushing 150 MPH? My 4th is 125+

06-26-2014, 10:22 PM	#32 (permalink)
future370zzz Track Member Join Date: Dec 2011 Location: Bay Area Posts: 555 Drives: 10 Nissan 370z Rep Power: 14	I have an sensor added after the MAF sensor and just before the intercooler. I see temperature of around 140 F when it's warmed up, in 75 F ambient weather. Unfortunately didn't install a sensor after the intercooler just before it enters the engine. Aghhhh That will be the next step depending on how much it would cost now to add a sensor after everything has been installed. The gauge and sensor install alone was $1K. __________________

07-10-2014, 11:22 AM	#36 (permalink)
ANMVQ A True Z Fanatic Join Date: Mar 2011 Location: Framingham MA Posts: 2,732 Drives: 2014 Q50 AWD Rep Power: 19	Not sure about the manuals but the 7 spd autos are 4th. __________________ 14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

09-04-2014, 12:26 PM	#38 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	A lot of tuning passes are done in 4th to reduce load and keep the car from hitting the limiter, the final hp numbers run should be done in 5th. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom intake setup -- Stillen G3's, Velocity Stacks, Custom Front Crash Beam, pics	'10Anamoly	Intake/Exhaust	26	02-14-2015 11:59 AM
stillen supercharger custom tune	hyunsoo1803	Forced Induction	23	08-21-2013 12:04 PM
UpRev Dyno Jet Tune - Stillen G3 Intake, Stillen CBE, M370, F.I. TP Shortie	scruffydog	Tuning	5	06-26-2013 03:25 AM
Forged Performance: Stillen SC Custom Tune and Review	Sharif@Forged	Forced Induction	26	09-20-2011 10:46 AM

07-10-2014, 08:59 AM	#35 (permalink)
fuct A True Z Fanatic Join Date: May 2009 Location: Sugar Land Posts: 3,692 Drives: 97' Ranger :) Rep Power: 24	arnt we supposed to do dyno pulls in 5th? charts say 4th...... no?