Boosted Performance turbo kit self install (review)

GaleForce · 09-24-2013, 07:57 AM

The canned tune was based off my car when it was at R/T Tuning. My car was ~460's HP with the original base map (also from Vince). I drove 8+ hours without an issue with that tune, then Vince touched it up when he was tuning my car. The base tune should be good to go without the boost controller. Having said that, you will probably want to have a tuner make adjustments dependant on fuel octane you intend to use, and your boost controller.

carlitos_370z · 09-24-2013, 08:08 AM

Nice work bro!!! I have a question.... its a dumb question loll!!! i always want to know if i install a turbo kit... i have to install forged internals too??? or i can run with oem internals... when i said forged internals i refer to piston & rods.... Let me know if you can... i want to do this on my car in the future

Thanks!!!

Chuck33079 · 09-24-2013, 08:13 AM

Quote:

Originally Posted by carlitos_370z

Nice work bro!!! I have a question.... its a dumb question loll!!! i always want to know if i install a turbo kit... i have to install forged internals too??? or i can run with oem internals... when i said forged internals i refer to piston & rods.... Let me know if you can... i want to do this on my car in the future

Thanks!!!

The rule of thumb here seems to be that you're fine on the stock motor at or below 500whp. Up to 550whp if you want to run on the ragged edge. Above that, plan for a motor build. Some people get away with 550whp for a long time, but that's being fairly aggressive with a stock motor. For peace of mind, stick around the 500 mark.

carlitos_370z · 09-24-2013, 08:55 AM

Quote:

Originally Posted by Chuck33079

The rule of thumb here seems to be that you're fine on the stock motor at or below 500whp. Up to 550whp if you want to run on the ragged edge. Above that, plan for a motor build. Some people get away with 550whp for a long time, but that's being fairly aggressive with a stock motor. For peace of mind, stick around the 500 mark.

Thanks a lot Chuck....

G37sHKS · 09-24-2013, 09:28 AM

Quote:

Originally Posted by Chuck33079

The rule of thumb here seems to be that you're fine on the stock motor at or below 500whp. Up to 550whp if you want to run on the ragged edge. Above that, plan for a motor build. Some people get away with 550whp for a long time, but that's being fairly aggressive with a stock motor. For peace of mind, stick around the 500 mark.

Its not the horse power that breaks the engine apart, its the torque (wheel torque). That being said, a good tune of 600 "WHP" will be much more reliable than bad tune with 350 WHP and will last much longer too.

Chuck33079 · 09-24-2013, 09:30 AM

Quote:

Originally Posted by G37sHKS

Its not the horse power that breaks the engine apart, its the torque (wheel torque). That being said, a good tune of 600 "WHP" will be much more reliable than bad tune with 350 WHP and will last much longer too.

Well, yeah. The one with the good tune always wins. I was using "a good tune" as a constant.

SPOHN · 09-24-2013, 10:02 AM

Nice write up

Cell · 09-24-2013, 10:30 AM

Quote:

Originally Posted by OldBoy

The car's lookin' good. I'm glad everything is working out for you Cell. If I was you tho, I would've had the clutch done before the install, that way the shop that will do your clutch would've removed the demon bolts for you since the exhaust needs to come out anyway

.

Looking forward to those dyno results.

Quote:

Originally Posted by Infidel

Not to mention you need to put a few miles on the fresh clutch before the tune/dyno.

I knew someone was going to mention it.

The only reason why I did the install first was because I rent my garage and I was getting kicked out. I wanted to take advantage of the time I had left with the garage and learn to do the install myself.

Quote:

Originally Posted by GaleForce

The canned tune was based off my car when it was at R/T Tuning. My car was ~460's HP with the original base map (also from Vince). I drove 8+ hours without an issue with that tune, then Vince touched it up when he was tuning my car. The base tune should be good to go without the boost controller. Having said that, you will probably want to have a tuner make adjustments dependant on fuel octane you intend to use, and your boost controller.

The tune I received is locked. So I will have to go with a fresh tune if I wanted changes. I asked for the password but I don't think Sasha was able to get it.

wagz · 09-24-2013, 11:25 AM

Cell how has your experience been with project x. They seem to be the only reputable Z shop in the Chicago land area.

Cell · 09-24-2013, 11:46 AM

Quote:

Originally Posted by wagz

Cell how has your experience been with project x. They seem to be the only reputable Z shop in the Chicago land area.

This is the second time I have gone to them for work. THe first time was just for the cat back install. The service there has been great so far. I don't have any complaints.

ENT-Z · 09-25-2013, 10:29 PM

Nice work! I have been enjoying mine now for about 7 months and running strong.

Mr&Mrs · 09-25-2013, 10:34 PM

Nice work man!

Cell · 09-26-2013, 11:27 AM

Thank you guys.

I believe the clutch and flywheel is in now. Car is still at the shop, probably getting the exhaust fabbed and a few other things looked over.

Can't wait till I finish breaking in the clutch so I can get it dynoed and tuned.

Cell · 10-02-2013, 04:34 PM

A little update...

I just got the car back today from Project X Customs. Car runs great. One problem with the tune is that it is running a little rich. It will have to be retuned.

Southbend's stage 3 clutch and 19lb flywheel sounds like a tractor trailer. I forgot to tell Project X customs to put the Motul oil that came with the Southbend clutch in so I will have to bring it back another day.

A small thing I noticed after getting my car back was that the turbo manifold actually blocks the port to fill the transmission with the motul oil.

Car feels like stock when it is out of boost. WHen it is in boost, it feels great. With the current CNT exhaust, it is actually not that loud and the BOV + Turbo spool sounds louder. Kind of makes me want to go with open dumps.

Now I have to break the clutch in with 500-1000 miles of city driving, then get it retuned and have the gauges mounted to where the center cubby hole is.

EDIT: Forgot to mention that oil now sits around 185-190 while cruising at 70mph in 75 degree weather. That is with a 30r oil cooler.

Mitco39 · 10-02-2013, 04:55 PM

You have to pull the piping to change the trans fluid. Just do it when you change the air filter since you will be in there anyways. I suggest ordering a couple more air filters from Sasha to keep as they usually come out with rub marks since the space is so tight.

Enjoy the boost, hopefully the snow stays away for you for some time yet.

09-24-2013, 07:57 AM	#16 (permalink)
GaleForce A True Z Fanatic Join Date: Aug 2011 Location: Ontario, Canada Posts: 21,749 Drives: Varis Arising II Rep Power: 51865	The canned tune was based off my car when it was at R/T Tuning. My car was ~460's HP with the original base map (also from Vince). I drove 8+ hours without an issue with that tune, then Vince touched it up when he was tuning my car. The base tune should be good to go without the boost controller. Having said that, you will probably want to have a tuner make adjustments dependant on fuel octane you intend to use, and your boost controller. carlitos_370z likes this. __________________ >>>GaleForce's Build<<< >>>FaceBook @3GsCustoms<<<>>>Instagram @GaleForce370z<<< Varis Kamikaze-Z

09-24-2013, 10:02 AM	#22 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	Nice write up carlitos_370z likes this. __________________

09-25-2013, 10:34 PM	#27 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Nice work man! __________________ Project Z <--Click - Check out the link too many mods to list!

10-02-2013, 04:34 PM	#29 (permalink)
Cell A True Z Fanatic Join Date: Jan 2010 Location: Chicago Posts: 1,449 Drives: A Garbage Truck Rep Power: 21	A little update... I just got the car back today from Project X Customs. Car runs great. One problem with the tune is that it is running a little rich. It will have to be retuned. Southbend's stage 3 clutch and 19lb flywheel sounds like a tractor trailer. I forgot to tell Project X customs to put the Motul oil that came with the Southbend clutch in so I will have to bring it back another day. A small thing I noticed after getting my car back was that the turbo manifold actually blocks the port to fill the transmission with the motul oil. Car feels like stock when it is out of boost. WHen it is in boost, it feels great. With the current CNT exhaust, it is actually not that loud and the BOV + Turbo spool sounds louder. Kind of makes me want to go with open dumps. Now I have to break the clutch in with 500-1000 miles of city driving, then get it retuned and have the gauges mounted to where the center cubby hole is. EDIT: Forgot to mention that oil now sits around 185-190 while cruising at 70mph in 75 degree weather. That is with a 30r oil cooler. Mr&Mrs and carlitos_370z like this. Last edited by Cell; 10-02-2013 at 06:11 PM.

10-02-2013, 04:55 PM	#30 (permalink)
Mitco39 A True Z Fanatic Join Date: Aug 2012 Location: Edmonton Alberta Canada Posts: 2,089 Drives: 40th 370z Rep Power: 132	You have to pull the piping to change the trans fluid. Just do it when you change the air filter since you will be in there anyways. I suggest ordering a couple more air filters from Sasha to keep as they usually come out with rub marks since the space is so tight. Enjoy the boost, hopefully the snow stays away for you for some time yet. GaleForce and carlitos_370z like this. __________________ 2007 Chevy Duramax - EFILive Tuned By Me 2010 40th W/ Nav - Boosted Performance - UpRev Tuned By Me The Mrs. Ride -2012 335XI N55 BMW - Cobb Tuned By Me, Built by her My Build --> http://www.the370z.com/members-370z-...39s-build.html

09-24-2013, 08:08 AM	#17 (permalink)
carlitos_370z A True Z Fanatic Join Date: Jul 2013 Location: Puerto Rico Posts: 7,157 Drives: 13 Nissan 370Z SP M6 Rep Power: 7586	Nice work bro!!! I have a question.... its a dumb question loll!!! i always want to know if i install a turbo kit... i have to install forged internals too??? or i can run with oem internals... when i said forged internals i refer to piston & rods.... Let me know if you can... i want to do this on my car in the future Thanks!!!

09-24-2013, 11:25 AM	#24 (permalink)
wagz Base Member Join Date: Jun 2010 Location: Chi Posts: 25 Drives: Need a Z Rep Power: 15	Cell how has your experience been with project x. They seem to be the only reputable Z shop in the Chicago land area.

09-25-2013, 10:29 PM	#26 (permalink)
ENT-Z Enthusiast Member Join Date: Feb 2009 Location: St. Louis, MO Posts: 460 Drives: 09 MB 6MT 370Z Rep Power: 16	Nice work! I have been enjoying mine now for about 7 months and running strong.

09-26-2013, 11:27 AM	#28 (permalink)
Cell A True Z Fanatic Join Date: Jan 2010 Location: Chicago Posts: 1,449 Drives: A Garbage Truck Rep Power: 21	Thank you guys. I believe the clutch and flywheel is in now. Car is still at the shop, probably getting the exhaust fabbed and a few other things looked over. Can't wait till I finish breaking in the clutch so I can get it dynoed and tuned.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance single turbo build	Boosted Performance	Forced Induction	1841	09-06-2016 12:17 PM
Boosted Performance single turbo results	Boosted Performance	Forced Induction	136	06-18-2014 06:40 PM
Forged Performance: HKS GT800 Turbo Kit Install	ChadB@Forged	Member's 370Z Gallery	7	05-17-2011 04:10 PM
Good performance shop for turbo install in dfw?	Andyy	Forced Induction	3	04-26-2011 11:27 PM
NoGood Review \| R2C Performance Intake Install	nogoodname	Intake/Exhaust	114	08-29-2009 09:28 AM