Boosted Performance round 2 list

Joepro · 04-30-2014, 10:31 PM

Quote:

Originally Posted by jwick

Probably something added by Vince. My tuner has it full on at anything above 100degC. Up to that its a gradient. I prefer it that way but then again I live in Texas

Vince does this on every Z he tunes to my knowledge, mine were set there na, you now have an huge intercooler and an oil cooler blocking your rad, you want those fans pulling the air through, and these cars ar know for extreme engine temps...I say not overkill IMO! I almost hit 200 on oil after doing a couple runs while tweaking the boost controller, still that is impressive to me, once I have some better motoring(wishing I added water temp now, I may in the future) to see how my stock rad is keeping up. As for the pump, once the car is running I am almost accustomed to it, I have to listen for it now.

jwick · 04-30-2014, 10:35 PM

I also noticed substantially higher temps after I got tuned and turned up the boost. On WG I could barely get it to 90degC. Now that I'm running close to 10lbs I see 105degC when romping on it. I am in Houston though so its naturally hotter.

Radride · 04-30-2014, 11:01 PM

Quote:

Originally Posted by Cell

Doesn't make sense.

If the injectors are designed to run E85 then why does it need to be cleaned so often? If your fuel system doesn't have the equipment to support E85, you shouldn't be running E85 anyways because of it being corrosive.

I came from supra's where guys run E85 all the time. A shop posted pics of injectors that were one years old and how bad they looked. They recommended getting them cleaned yearly. It might be over kill but when you're tuned on the raged edge or making over 1000whp, what's a couple hundred bucks a year for piece of mind.

R.K.

TopgunZ · 04-30-2014, 11:40 PM

As much as E85 can be a pain in the ***, its benefits outweigh its negatives. All this cooling discussion has me thinking of its latent heat of vaporization properties. It literally pulls 3x the amount of heat out of the cylinder and runs your block temps cooler.

jwick · 05-07-2014, 11:08 PM

So I snapped a t-bolt while doing routine checks. I prefer the t-bolt clamps that have the round shank instead of the square like came with the kit. I also had to cut a few to clearance rubbing points which makes them one time use. Short story long I'm going to replace them the next time I do complete maintenance. Can anyone confirm my counts?

6 - 2.75"
12 - 2.5"
1 - 3"
1 - 2"

blackonorange · 05-08-2014, 12:37 PM

I broke one to. They don't take much to break. They I found out they don't need to be kryptynite (spelling?) tight.

jwick · 05-08-2014, 01:19 PM

Quote:

Originally Posted by blackonorange

I broke one to. They don't take much to break. They I found out they don't need to be kryptynite (spelling?) tight.

The thing about mine was I wasn't really applying that much torque. Thankfully I had a spare 2.5" t-bolt that I stole from my G3 intake. Guess I'll have to replace it before I install it on the buyers car.

09nismo498 · 05-08-2014, 04:42 PM

vibrant makes them. Have used them many times, very good clamps. I broke a couple as well, sasha replaced them free of charge. if they break next time i loosen or tighten them, i will go with vibrant clamps.

Joe@ZSpeed · 05-08-2014, 05:09 PM

Hose

Boosted Performance · 05-08-2014, 06:03 PM

If these are breaking, you guys are over tightening them. They really don't need to be very tight, as all the pipes are bead rolled. I have installed at least a hundred of these clamp and never had one let go, or even hint at failure. This includes some cars that are pushing 30+psi. Never an issue.

Cell · 05-09-2014, 12:01 AM

Hit 215 degrees on the oil today. This is with 75-80 degree weather. First time seeing 215 with the kit.

jwick · 05-09-2014, 12:04 AM

Quote:

Originally Posted by Cell

Hit 215 degrees on the oil today. This is with 75-80 degree weather. First time seeing 215 with the kit.

I don't even think I hit that on the dyno and I live in Houston

TopgunZ · 05-09-2014, 05:03 PM

Well those muther ******* bad luck trolls are still clinging to me.

Want to know what happens when a boost controller goes bad on a dyno?

You get 19.5 lbs of boost and 680 torque to the wheels at 4000 rpm.

Good news is my engine is still in one piece!

So after I ripped that out we made 465whp and 430tq on 9lb wastegate springs. Probably going to be putting the 11lb springs in this weekend then going back to break 500.

Cell · 05-09-2014, 05:07 PM

Quote:

Originally Posted by TopgunZ

Well those muther ******* bad luck trolls are still clinging to me.

Want to know what happens when a boost controller goes bad on a dyno?

You get 19.5 lbs of boost and 680 torque to the wheels at 4000 rpm.

Good news is my engine is still in one piece!

Damn I think you just made the record for highest power from a stock block. LOL

TopgunZ · 05-09-2014, 05:13 PM

Quote:

Originally Posted by Cell

Damn I think you just made the record for highest power from a stock block. LOL

Hahaha... The spool on that turbo is SCARY at those levels. It sounded like it was going to suck the intake filter straight through it. Ill throw up the graph here in a bit. I had them print it out..lol.

04-30-2014, 10:35 PM	#1367 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	I also noticed substantially higher temps after I got tuned and turned up the boost. On WG I could barely get it to 90degC. Now that I'm running close to 10lbs I see 105degC when romping on it. I am in Houston though so its naturally hotter. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

04-30-2014, 11:40 PM	#1369 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	As much as E85 can be a pain in the *, its benefits outweigh its negatives. All this cooling discussion has me thinking of its latent heat of vaporization properties. It literally pulls 3x the amount of heat out of the cylinder and runs your block temps cooler. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM**

05-07-2014, 11:08 PM	#1370 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	So I snapped a t-bolt while doing routine checks. I prefer the t-bolt clamps that have the round shank instead of the square like came with the kit. I also had to cut a few to clearance rubbing points which makes them one time use. Short story long I'm going to replace them the next time I do complete maintenance. Can anyone confirm my counts? 6 - 2.75" 12 - 2.5" 1 - 3" 1 - 2" __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-08-2014, 04:42 PM	#1373 (permalink)
09nismo498 Base Member Join Date: Sep 2010 Location: Chicago burbs Posts: 207 Drives: 14 GTR Rep Power: 16	vibrant makes them. Have used them many times, very good clamps. I broke a couple as well, sasha replaced them free of charge. if they break next time i loosen or tighten them, i will go with vibrant clamps. __________________ 2013 370z Nismo Turbo 2017 Lexus IS200T F Sport (DD)

05-08-2014, 05:09 PM	#1374 (permalink)
Joe@ZSpeed A True Z Fanatic Join Date: Mar 2011 Location: Ohio Posts: 1,304 Drives: Nissan Rep Power: 342999	Hose jlo370z likes this. __________________ http://photos.zspeedperformance.com/...ardsize=468x60 Phone *937-506-7224* E-Mail Sales@Zspeed.com www.ZSPEED.com

05-08-2014, 12:37 PM	#1371 (permalink)
blackonorange A True Z Fanatic Join Date: Jul 2011 Location: Saskatchewan Posts: 1,078 Drives: 09 370z Rep Power: 16	I broke one to. They don't take much to break. They I found out they don't need to be kryptynite (spelling?) tight.

05-08-2014, 06:03 PM	#1375 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	If these are breaking, you guys are over tightening them. They really don't need to be very tight, as all the pipes are bead rolled. I have installed at least a hundred of these clamp and never had one let go, or even hint at failure. This includes some cars that are pushing 30+psi. Never an issue. LMBmikeZ likes this. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

05-09-2014, 12:01 AM	#1376 (permalink)
Cell A True Z Fanatic Join Date: Jan 2010 Location: Chicago Posts: 1,449 Drives: A Garbage Truck Rep Power: 21	Hit 215 degrees on the oil today. This is with 75-80 degree weather. First time seeing 215 with the kit.

05-09-2014, 05:03 PM	#1378 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Well those muther ***** bad luck trolls are still clinging to me. Want to know what happens when a boost controller goes bad on a dyno? You get 19.5 lbs of boost and 680 torque to the wheels at 4000 rpm. Good news is my engine is still in one piece! So after I ripped that out we made 465whp and 430tq on 9lb wastegate springs. Probably going to be putting the 11lb springs in this weekend then going back to break 500. jlo370z likes this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM** Last edited by TopgunZ; 05-09-2014 at 05:10 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance single turbo build	Boosted Performance	Forced Induction	1841	09-06-2016 12:17 PM
Boosted Performance single turbo results	Boosted Performance	Forced Induction	136	06-18-2014 06:40 PM
2012 Option List Includes Dealer-Installed Performance	SeattleLion	Nissan 370Z General Discussions	3	10-08-2011 03:21 PM
Come support A.M. Performance at the Laguna Seca Grand Am round next weekend!!!!!!!	Mike@AMPerformance	Nissan 370Z General Discussions	16	07-14-2011 12:47 AM
Come support A.M. Performance at the Laguna Seca Grand Am round next weekend!!!!!!!	Mike@AMPerformance	Northern California Region	0	07-01-2011 08:13 PM