Boosted Performance round 2 list

TopgunZ · 03-03-2014, 05:37 PM

Quote:

Originally Posted by jwick

You picking up a BP kit?

No I haven't. I had the Powerlab kit with the Stillen kit on the 350.

@ Sasha.. The blanket I had said it can be used for T3 or T4. Not sure how that translates but it was a bit saggy on the T3 and the T4 might be a tight fit.

I cant remember where this is addressed in the numerous threads on the BP kit but talking about all these heat issues makes me wonder. Have you ever looked into designing a heat shield as an option to the kit? Or would this truly not add any value in heat dissipation from the transmission?

jwick · 03-03-2014, 05:47 PM

Quote:

Originally Posted by TopgunZ

@ Sasha.. The blanket I had said it can be used for T3 or T4. Not sure how that translates but it was a bit saggy on the T3 and the T4 might be a tight fit.

I can speak from experience as I have both the turbo and blanket in hand. I seriously doubt the bag you are referring to will work. I bought the DEI turbo blanket for a T4 frame and because this turbo is a twin scroll, the bag does not cover the entire inlet side. It's close like probably 95ish percent but definitely not a complete cover.

Boosted Performance · 03-03-2014, 06:48 PM

Quote:

Originally Posted by jwick

I can speak from experience as I have both the turbo and blanket in hand. I seriously doubt the bag you are referring to will work. I bought the DEI turbo blanket for a T4 frame and because this turbo is a twin scroll, the bag does not cover the entire inlet side. It's close like probably 95ish percent but definitely not a complete cover.

That sounds about right. The tangential T4 housings are large, but the twin scroll is very large.

Big boy power needs big boy turbine.

jwick · 03-03-2014, 06:55 PM

Quote:

Originally Posted by Boosted Performance

That sounds about right. The tangential T4 housings are large, but the twin scroll is very large.

Big boy power needs big boy turbine.

You aren't lying. Here's a pic I took the other day for a size reference.

GaleForce · 03-03-2014, 06:56 PM

Quote:

Originally Posted by Boosted Performance

No issues should ever come up if the instructions are followed. There is plenty of room to keep everything plenty far enough from anything that will get hot.

Your PL turbo blanket will be waaaaaay too small for this turbine housing. You need a large T4 blanket.

If you're following the excellent instruction manual you will find the waste gate hoses (any of the kits additional hoses for that matter) don't go anywhere near the hot stuff. That is unless you are making an effort to test the temperature rating of the silicone hoses by wire tying them to the hot pipes. If that's the case... I say good luck to you.

megalapagas · 03-03-2014, 08:11 PM

Sasha sent you a pm are you availabke atn to speak to you over the phone?

jwick · 03-03-2014, 11:36 PM

I finished wrapping everything this evening. I tried to test fit a waste gate to the piping and I could not get clamps far enough closed to slide the bolt through. I double checked and there is no interference from the wrap. I think (did not try) I could get them on maybe if I used a pair of channel locks but it seemed wrong to take that much effort.

Are they supposed to require that level of force to get the clamps around the flanges? It doesn't seem like it considering the instructions say I have to clock them prior to tightening the clamps. There is no way to rotate the WG once the flange is tight and you still can't get the bolt through.

TopgunZ · 03-03-2014, 11:40 PM

Are the v bands for the bov and gates the same size? Maybe you are doing that.... Just a thought.

jwick · 03-04-2014, 12:00 AM

Quote:

Originally Posted by TopgunZ

Are the v bands for the bov and gates the same size? Maybe you are doing that.... Just a thought.

I didn't get to the BOV as I've not messed with any IC piping. The WG comes with two different clamps in the box. One (I'll call the inlet) attaches to the pipe leading to the turbo, the second (outlet) attached to the recirulated WG piping. I tried both WGs which leads me to believe its not a manufacturer error since both are the same. It is so tight that there is no way to rotate it and I had to pry the clamp back apart with a pair of needle nose just to get the clamps off.

Maybe someone that has done this can chime in or Sasha will tomorrow.

Cell · 03-04-2014, 12:00 AM

Quote:

Originally Posted by jwick

I finished wrapping everything this evening. I tried to test fit a waste gate to the piping and I could not get clamps far enough closed to slide the bolt through. I double checked and there is no interference from the wrap. I think (did not try) I could get them on maybe if I used a pair of channel locks but it seemed wrong to take that much effort.

Are they supposed to require that level of force to get the clamps around the flanges? It doesn't seem like it considering the instruction say I have to clock them prior to tightening the clamps. There is no way to rotate the WG once the flange is tight and you still can't get the bolt through.

I clamped that sucker together with a channel lock. LOL It was tight for me too. That's the way I like it.

jwick · 03-04-2014, 12:03 AM

Quote:

Originally Posted by Cell

I clamped that sucker together with a channel lock. LOL It was tight for me too. That's the way I like it.

You must be my brotha from a anotha motha, cuz I like the sh!t tight too.

Thanks man. I was just kind of scared to need to apply that much force.

Cell · 03-04-2014, 12:06 AM

Quote:

Originally Posted by jwick

You must be my brotha from a anotha motha, cuz I like the sh!t tight too.

Thanks man. I was just kind of scared to need to apply that much force.

No seriously though, just clamp it tight enough so you can get the screw in. Just make sure you align things up first then put the screw in.

Boosted Performance · 03-04-2014, 12:37 AM

That is a bit odd. It is possible that the machining of the flanges or clamps is a bit off, and they are tight for that reason. I have seen it a couple of times where there is bit of a burr on the outside edge of the flange, and it can cause a very tight fit of the clamp.

Cell · 03-04-2014, 12:56 AM

Quote:

Originally Posted by Boosted Performance

That is a bit odd. It is possible that the machining of the flanges or clamps is a bit off, and they are tight for that reason. I have seen it a couple of times where there is bit of a burr on the outside edge of the flange, and it can cause a very tight fit of the clamp.

It was decently tight for me. I ended up using a channel lock to get the screw in. wondering if heat would loosen them up.

Sounds like it might be time for a check up this summer.

AlexRaymond19 · 03-04-2014, 07:42 AM

Thinking about buying this kit. From the instructions its looks as though it uses the stock headers... Which is great because those are a pain in the *** to take off. Only problem is I installed momentum DE headers. Anyway I can get the kit fabricated with the DE fittings?

Also, is the car anymore unsafe without the crash bar? Or is that mainly to protect the engine and engine bay componenets?

03-03-2014, 08:11 PM	#666 (permalink)
megalapagas Enthusiast Member Join Date: May 2013 Location: McAllen,TX Posts: 457 Drives: '10 370Z Tour A/T Rep Power: 12	Sasha sent you a pm are you availabke atn to speak to you over the phone? __________________ GTM 34 Row Oil Cooler \| K&N Drop Ins w/ Z1's Post MAF Tubes \| F.I Non-Res'd 2.5" T.P w/ CF CBE \| Axis Wheels \| Piecing together My Own Custom T4 Top Mount Single Turbo Kit Still in the works \|

03-03-2014, 11:36 PM	#667 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	I finished wrapping everything this evening. I tried to test fit a waste gate to the piping and I could not get clamps far enough closed to slide the bolt through. I double checked and there is no interference from the wrap. I think (did not try) I could get them on maybe if I used a pair of channel locks but it seemed wrong to take that much effort. Are they supposed to require that level of force to get the clamps around the flanges? It doesn't seem like it considering the instructions say I have to clock them prior to tightening the clamps. There is no way to rotate the WG once the flange is tight and you still can't get the bolt through. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build Last edited by jwick; 03-04-2014 at 12:01 AM.

03-03-2014, 11:40 PM	#668 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Are the v bands for the bov and gates the same size? Maybe you are doing that.... Just a thought. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

03-04-2014, 12:37 AM	#673 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	That is a bit odd. It is possible that the machining of the flanges or clamps is a bit off, and they are tight for that reason. I have seen it a couple of times where there is bit of a burr on the outside edge of the flange, and it can cause a very tight fit of the clamp. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

03-04-2014, 07:42 AM	#675 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 15	Thinking about buying this kit. From the instructions its looks as though it uses the stock headers... Which is great because those are a pain in the * to take off. Only problem is I installed momentum DE headers. Anyway I can get the kit fabricated with the DE fittings? Also, is the car anymore unsafe without the crash bar? Or is that mainly to protect the engine and engine bay componenets? __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang**

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Boosted Performance single turbo build	Boosted Performance	Forced Induction	1841	09-06-2016 12:17 PM
Boosted Performance single turbo results	Boosted Performance	Forced Induction	136	06-18-2014 06:40 PM
2012 Option List Includes Dealer-Installed Performance	SeattleLion	Nissan 370Z General Discussions	3	10-08-2011 03:21 PM
Come support A.M. Performance at the Laguna Seca Grand Am round next weekend!!!!!!!	Mike@AMPerformance	Nissan 370Z General Discussions	16	07-14-2011 12:47 AM
Come support A.M. Performance at the Laguna Seca Grand Am round next weekend!!!!!!!	Mike@AMPerformance	Northern California Region	0	07-01-2011 08:13 PM