Anyone seen this code? U1024,VVEL CAN communication

Mr&Mrs · 04-07-2013, 08:17 PM

Subd for rop's info.

roplusbee · 04-07-2013, 10:07 PM

Glad you found the problem. Now I just have to deliver on that P1421 issue fix action.

Sent from my D-Team-MT4GS-CM10.1

rhd · 04-07-2013, 10:58 PM

Quote:

Originally Posted by cosmogirl

Ok after looking over things it seems the positive wire coming from the alternator going to the battery rubbed against the exhaust manifold causing it to melt and blow that 140A fuse on top of the battery. I have already replaced that cable and made sure this time around that it was no where near the exhaust manifold. Finished up everything and started it up with No codes..... Cant thank you guys enough for such a great community on helping each other out.

Glad you found the problem and got it fixed up.

COSMO · 04-08-2013, 01:56 AM

Well hopefully that fixes the problem, today I will drive it again to see what happens. Before all of that the car would just die when you got on it hard but would allow you to restart it all without throwing a code. Cant say enough about gtm in regards customer service, Sam, Pablo, and mike have been excellent!!

COSMO · 04-08-2013, 06:54 PM

Drove the car again today after going through everything again and it seemed to be fine with no engine light. Now the DTC light stays on and the light above it showing the other half of the traction control system light also stays on. Whats weird is when I turn the car off and start it again it goes away but comes on shortly after driving... Guess Iam going to have to live with it being on all of the time...

SAM@GTM · 04-08-2013, 07:22 PM

Quote:

Originally Posted by cosmogirl

Drove the car again today after going through everything again and it seemed to be fine with no engine light. Now the DTC light stays on and the light above it showing the other half of the traction control system light also stays on. Whats weird is when I turn the car off and start it again it goes away but comes on shortly after driving... Guess Iam going to have to live with it being on all of the time...

You don't have to live with it, it is a simple fix. This is happening because the steering angle sensor did not go back to its original position (miss-aligned steering coupler). So basically, what is happening is that every time you shut off the car, it resets itself and will not trigger the VDC light until the steering angle sensor indicates a problem and that is what is happening when you make a turn. So there are two solutions: relearn the steering angle position via CONSULT III or recheck/redo your installation on the steering coupler.

Sam

roplusbee · 04-20-2013, 10:24 AM

Just wanted to pop in and let you guys know that I have an appointment with UPREV next week for inspection/troubleshooting. For some reason, I only have the P1421 code on my low boost map and boost control setting. If I run my high boost tune and boost control setting, no P1421. Strange..........

Props to Sam for popping in and offering solutions to Cosmo's issue.

Sent from my SGH-T889 using Tapatalk 2

COSMO · 04-20-2013, 03:33 PM

Going on vacay for a week so will check back when I get back...

N0SL3N · 05-15-2013, 08:16 AM

I'm back but this time I got the U1024. Only happened when I flashed back to stock. I was putting the sl fuse back in the ipdm so I hope I didn't mess with anything. Car still seems to run fine though.

COSMO · 05-15-2013, 10:54 AM

I finally had to take it to Nissan and they had to reset the steering angle to 0 and replace my clock spring but they did it under warranty.. I was sweating bullets while negotiating if they would do it under warranty. All fixed and good...

Stino · 05-07-2018, 09:54 AM

COSMO

I was looking at an old thread you posted on error code U1024. I’m getting the same code and not sure what is causing it. Do you remember specifically what the issue was?

Here is a list of my add-on/mods:

1. UpRev
2. Berk High Flow Cats and Cat aBack Exhaust
3. Nismo Cold Air Intakes
4. Mishimoto Aluminum Radiator
5. Oil & Power Steering Coolers

Any help would be much appreciated. Thanks!

JARblue · 05-07-2018, 10:10 AM

I don't think he will be responding. I believe he is currently serving a lifetime ban from the forum.

Rusty · 05-07-2018, 11:57 PM

He hasn't posted in 2 years. When his motor blew the last time. That was it for him. He has moved on.

Stino · 05-18-2018, 04:07 AM

My Z is fixed and running better than ever. I replaced the VEL control Module, adjusted the VEL Actuator Sensors myself with UpRev software and didn't have to part with $3200 like the Nissan dealer said I needed to.

When I took my car to Nissan and supposedly spoke to their top mechanic, he had no clue what I was talking about until I showed him in the 370Z service manual. There is absolutely no excuse for that if you are the top shop mechanic.

Do yourself a favor and read the service manual; you'll know just as much as the Nissan Dealer Mechanics.

mitchkrainin · 07-25-2019, 10:36 AM

Quote:

Originally Posted by roplusbee

Just wanted to pop in and let you guys know that I have an appointment with UPREV next week for inspection/troubleshooting. For some reason, I only have the P1421 code on my low boost map and boost control setting. If I run my high boost tune and boost control setting, no P1421. Strange..........

Props to Sam for popping in and offering solutions to Cosmo's issue.

Sent from my SGH-T889 using Tapatalk 2

What was the fix for the P1421 out of curiosity? My Z is getting it now after an UPREV tune and ART Pipes.

04-07-2013, 08:17 PM	#16 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Subd for rop's info. __________________ Project Z <--Click - Check out the link too many mods to list!

04-07-2013, 10:07 PM	#17 (permalink)
roplusbee A True Z Fanatic Join Date: Dec 2009 Location: Killeen, TX Posts: 2,360 Drives: 2007 350Z NISMO Rep Power: 23	Glad you found the problem. Now I just have to deliver on that P1421 issue fix action. Sent from my D-Team-MT4GS-CM10.1 Mr&Mrs likes this. __________________ 2007 350Z NISMO #0618: Zerolift \| UPREV \| F.I. \| Greddy \| Competition Clutch \| Injector Dynamics \| Aeromotive \| Pioneer \| JL

04-08-2013, 01:56 AM	#19 (permalink)
COSMO A True Z Fanatic Join Date: Dec 2012 Location: FL Posts: 1,816 Drives: 2012 Touring GTM TT Rep Power: 20	Well hopefully that fixes the problem, today I will drive it again to see what happens. Before all of that the car would just die when you got on it hard but would allow you to restart it all without throwing a code. Cant say enough about gtm in regards customer service, Sam, Pablo, and mike have been excellent!! Mr.Squeeze likes this.

04-20-2013, 10:24 AM	#22 (permalink)
roplusbee A True Z Fanatic Join Date: Dec 2009 Location: Killeen, TX Posts: 2,360 Drives: 2007 350Z NISMO Rep Power: 23	Just wanted to pop in and let you guys know that I have an appointment with UPREV next week for inspection/troubleshooting. For some reason, I only have the P1421 code on my low boost map and boost control setting. If I run my high boost tune and boost control setting, no P1421. Strange.......... Props to Sam for popping in and offering solutions to Cosmo's issue. Sent from my SGH-T889 using Tapatalk 2 COSMO likes this. __________________ 2007 350Z NISMO #0618: Zerolift \| UPREV \| F.I. \| Greddy \| Competition Clutch \| Injector Dynamics \| Aeromotive \| Pioneer \| JL

05-15-2013, 08:16 AM	#24 (permalink)
N0SL3N Enthusiast Member Join Date: Nov 2011 Location: Toronto Posts: 376 Drives: 2009 PG 370z 6MT Rep Power: 35	I'm back but this time I got the U1024. Only happened when I flashed back to stock. I was putting the sl fuse back in the ipdm so I hope I didn't mess with anything. Car still seems to run fine though. __________________ \| Akuma \| Motordyne \| Z1 \| NST \| CNT \| Stillen \| Avant Garde \| RJM \| Performix \| Tint \| LED \| GTR \| Nissan \|

04-08-2013, 06:54 PM	#20 (permalink)
COSMO A True Z Fanatic Join Date: Dec 2012 Location: FL Posts: 1,816 Drives: 2012 Touring GTM TT Rep Power: 20	Drove the car again today after going through everything again and it seemed to be fine with no engine light. Now the DTC light stays on and the light above it showing the other half of the traction control system light also stays on. Whats weird is when I turn the car off and start it again it goes away but comes on shortly after driving... Guess Iam going to have to live with it being on all of the time...

04-20-2013, 03:33 PM	#23 (permalink)
COSMO A True Z Fanatic Join Date: Dec 2012 Location: FL Posts: 1,816 Drives: 2012 Touring GTM TT Rep Power: 20	Going on vacay for a week so will check back when I get back...

05-15-2013, 10:54 AM	#25 (permalink)
COSMO A True Z Fanatic Join Date: Dec 2012 Location: FL Posts: 1,816 Drives: 2012 Touring GTM TT Rep Power: 20	I finally had to take it to Nissan and they had to reset the steering angle to 0 and replace my clock spring but they did it under warranty.. I was sweating bullets while negotiating if they would do it under warranty. All fixed and good... GaleForce likes this.

05-07-2018, 09:54 AM	#26 (permalink)
Stino Base Member Join Date: Apr 2011 Location: Florida Posts: 159 Drives: 2010 370Z Sport Rep Power: 15	Error code U1024 COSMO I was looking at an old thread you posted on error code U1024. I’m getting the same code and not sure what is causing it. Do you remember specifically what the issue was? Here is a list of my add-on/mods: 1. UpRev 2. Berk High Flow Cats and Cat aBack Exhaust 3. Nismo Cold Air Intakes 4. Mishimoto Aluminum Radiator 5. Oil & Power Steering Coolers Any help would be much appreciated. Thanks! __________________ 10 370Z Sport\|Berk CBE & HFC\|NISMO R-TUNE CAI\|Z1 Oil & PS Coolers\|Mishimoto Radiator\|UpRev\|Nismo S-Tune\|SEIBON Spoiler\|Eibach Sways, Springs, Spacers\|SPC Camber\|RJM Clutch Pedal\|Enkei Wheels\|StopTech Rotors & Pads\|SS Brake/Clutch Lines\|Alpine W900BT, PDX5, Rear Camera, Boston SR60, S35 & 10" G3 Sub\|3M Ceramic Tint

05-07-2018, 10:10 AM	#27 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 44 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684441	I don't think he will be responding. I believe he is currently serving a lifetime ban from the forum. cv129, elperuano, Chuck33079 and 1 others like this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

05-07-2018, 11:57 PM	#28 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,383 Drives: 2011 Nismo GM 6M Rep Power: 2684438	He hasn't posted in 2 years. When his motor blew the last time. That was it for him. He has moved on. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

05-18-2018, 04:07 AM	#29 (permalink)
Stino Base Member Join Date: Apr 2011 Location: Florida Posts: 159 Drives: 2010 370Z Sport Rep Power: 15	My Z is fixed and running better than ever. I replaced the VEL control Module, adjusted the VEL Actuator Sensors myself with UpRev software and didn't have to part with $3200 like the Nissan dealer said I needed to. When I took my car to Nissan and supposedly spoke to their top mechanic, he had no clue what I was talking about until I showed him in the 370Z service manual. There is absolutely no excuse for that if you are the top shop mechanic. Do yourself a favor and read the service manual; you'll know just as much as the Nissan Dealer Mechanics. B&W_Evader and Fountainhead like this. __________________ 10 370Z Sport\|Berk CBE & HFC\|NISMO R-TUNE CAI\|Z1 Oil & PS Coolers\|Mishimoto Radiator\|UpRev\|Nismo S-Tune\|SEIBON Spoiler\|Eibach Sways, Springs, Spacers\|SPC Camber\|RJM Clutch Pedal\|Enkei Wheels\|StopTech Rotors & Pads\|SS Brake/Clutch Lines\|Alpine W900BT, PDX5, Rear Camera, Boston SR60, S35 & 10" G3 Sub\|3M Ceramic Tint

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Confirmation or communication after ordering?	ryang	Nissan 370Z Pricing / Ordering Discussions	1	12-02-2011 02:13 PM
Vvel ????	pokeyl	Tuning	8	06-01-2011 03:33 PM
Car to Car communication	Osiris	Audio & Video	9	05-04-2011 04:00 AM
Vvel	destinyZ	Engine & Drivetrain	13	09-19-2010 06:32 PM
Code U1024	Megan370z	Tuning	9	03-15-2010 08:15 PM