Fast Intentions "Twin Turbo Kit" is here

mfeinst · 02-07-2013, 07:11 PM

Quote:

Originally Posted by Footloose301

Did you go back to MySpace?

Never touched that slime.

On topic: woot.

Dzel · 02-07-2013, 08:06 PM

I'm not even paying attention to what's going on at work cause I keep checking for uploads

jooonnn · 02-07-2013, 08:16 PM

so excited ^_^

m3chhawk · 02-07-2013, 10:13 PM

For those that aren't following FI on Facebook (https://www.facebook.com/FastIntentions)

Tony just posted a picture of the car strapped down on the dyno.

Dzel · 02-08-2013, 12:28 AM

Stupid company laptop doesn't let me get onto FB

F.I. Inc. · 02-08-2013, 01:33 AM

Update,

Just finished dyno testing the full 2.5" set up. The fuel pressure is dropping in the high end and we are going to sort that out. Here is what we have so far.

91 Octane:
469 RWH
382 FT LBS of Torque
Roughly 7-7.5 PSI

The boost is fluctuating between 6-7.5 LBS. We are currently running it on strictly wastegate spring pressure with no boost controller.

The timing is conservative because we only have 91 Octane and do not want to detonate, obviously!

Currently we are strapping the car down and testing it with stock cats and the full 2.5" CBE. Not expecting big numbers in this form and we are strictly doing it out of curiousity and to apease the community.

After this is complete we will take the full exhaust off and slap on the full 3". At that point it will get tested again tonight on 91 octane. Tomorrow once we can troubleshoot the slight fueling issue, we will turn the boot up on VP Motorsport 103 octane.

Here is what we can take away from this so far. At this PSI level we are not even close to utilizing the potential of what the GTX 28-67 turbo can do! The innercooler setup is proving to be extremely effiecent. After 13 runs we in fact made more power every time. The innercooler is not heat soaking and the IAT's (Inlet Air Temps.) are holding steady in the low 80's. The boost is ramping in fast and hard. The curve is very usable in the low end and mid range.

I will keep you posted shortly with another update.

Thanks, Tony

PontualZ · 02-08-2013, 01:44 AM

Quote:

Originally Posted by F.I. Inc.

Update,

Just finished dyno testing the full 2.5" set up. The fuel pressure is dropping in the high end and we are going to sort that out. Here is what we have so far.

91 Octane:
469 RWH
382 FT LBS of Torque
Roughly 7-7.5 PSI

The boost is fluctuating between 6-7.5 LBS. We are currently running it on strictly wastegate spring pressure with no boost controller.

The timing is conservative because we only have 91 Octane and do not want to detonate, obviously!

Currently we are strapping the car down and testing it with stock cats and the full 2.5" CBE. Not expecting big numbers in this form and we are strictly doing it out of curiousity and to apease the community.

After this is complete we will take the full exhaust off and slap on the full 3". At that point it will get tested again tonight on 91 octane. Tomorrow once we can troubleshoot the slight fueling issue, we will turn the boot up on VP Motorsport 103 octane.

Here is what we can take away from this so far. At this PSI level we are not even close to utilizing the potential of what the GTX 28-67 turbo can do! The innercooler setup is proving to be extremely effiecent. After 13 runs we in fact made more power every time. The innercooler is not heat soaking and the IAT's (Inlet Air Temps.) are holding steady in the low 80's. The boost is ramping in fast and hard. The curve is very usable in the low end and mid range.

I will keep you posted shortly with another update.

Thanks, Tony

DEpointfive0 · 02-08-2013, 01:53 AM

With stock cats, congrats brother, when do you need my 7AT?!?!?!

Mr.Squeeze · 02-08-2013, 02:04 AM

Nice Solid number's Tony cant wait to see the graph and 3 inch exhaust results.

F.I. Inc. · 02-08-2013, 02:09 AM

Quote:

Originally Posted by DEpointfive0

With stock cats, congrats brother, when do you need my 7AT?!?!?!

That is with straight Test Pipes. We just completed the stock cat runs. Here are the numbers.

91 Octane
431 RWH
355 FT LBS of torque
6.5-7.2 PSI

Still very respectable for stock cats! Again, no boost controller. Just straight wastegate spring pressure.

G37Sam · 02-08-2013, 02:38 AM

Congrats Tony! These are some sick numbers!

F.I. Inc. · 02-08-2013, 02:54 AM

Update,

No 3" tonight. Got shut down by Johnny law. Too much noise, too late in the evening. Will get back at it tomorrow. As of now it looks like we are going to make the track Saturday!

Stay tuned...

Thanks and goodnight.

Tony

blackonorange · 02-08-2013, 03:13 AM

What fuel pressure gauge do you have ?

asdfsammich · 02-08-2013, 03:31 AM

Damn! This is a hell of a good show!

Tapatalk & such etc

TerribleONE · 02-08-2013, 04:05 AM

Had a great day today Tony. You guys continue to surpass my expectations. Cant wait for tomorrow and saturday.

02-07-2013, 08:06 PM	#287 (permalink)
Dzel A True Z Fanatic Join Date: May 2011 Location: Midland, TX Posts: 3,884 Drives: 11 370Z PW M6 Rep Power: 23	I'm not even paying attention to what's going on at work cause I keep checking for uploads __________________ 10secWS6 IF YOU CAN'T SWING IT THEN DON'T BRING IT! Check out Domestic Performance C.C.

02-07-2013, 08:16 PM	#288 (permalink)
jooonnn Enthusiast Member Join Date: Oct 2012 Location: South Carolina Posts: 270 Drives: 2013 Nismo Rep Power: 13	so excited ^_^ __________________ Try things once to see how it feels. Try things a second time to make sure you didn't like it

02-08-2013, 12:28 AM	#290 (permalink)
Dzel A True Z Fanatic Join Date: May 2011 Location: Midland, TX Posts: 3,884 Drives: 11 370Z PW M6 Rep Power: 23	Stupid company laptop doesn't let me get onto FB __________________ 10secWS6 IF YOU CAN'T SWING IT THEN DON'T BRING IT! Check out Domestic Performance C.C.

02-08-2013, 01:33 AM	#291 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	Update, Just finished dyno testing the full 2.5" set up. The fuel pressure is dropping in the high end and we are going to sort that out. Here is what we have so far. 91 Octane: 469 RWH 382 FT LBS of Torque Roughly 7-7.5 PSI The boost is fluctuating between 6-7.5 LBS. We are currently running it on strictly wastegate spring pressure with no boost controller. The timing is conservative because we only have 91 Octane and do not want to detonate, obviously! Currently we are strapping the car down and testing it with stock cats and the full 2.5" CBE. Not expecting big numbers in this form and we are strictly doing it out of curiousity and to apease the community. After this is complete we will take the full exhaust off and slap on the full 3". At that point it will get tested again tonight on 91 octane. Tomorrow once we can troubleshoot the slight fueling issue, we will turn the boot up on VP Motorsport 103 octane. Here is what we can take away from this so far. At this PSI level we are not even close to utilizing the potential of what the GTX 28-67 turbo can do! The innercooler setup is proving to be extremely effiecent. After 13 runs we in fact made more power every time. The innercooler is not heat soaking and the IAT's (Inlet Air Temps.) are holding steady in the low 80's. The boost is ramping in fast and hard. The curve is very usable in the low end and mid range. I will keep you posted shortly with another update. Thanks, Tony iceman21_23, TerribleONE, Boost_lee and 6 others like this. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION"

02-08-2013, 02:04 AM	#294 (permalink)
Mr.Squeeze A True Z Fanatic Join Date: Aug 2010 Location: Keystone state Posts: 1,209 Drives: 2010 370z Rep Power: 20153	Nice Solid number's Tony cant wait to see the graph and 3 inch exhaust results. __________________ Driven Motorsports Single Turbo 7675 T4 1.32 A/R 995WHP 780TQ

02-07-2013, 10:13 PM	#289 (permalink)
m3chhawk Track Member Join Date: Sep 2012 Location: Kansas City Posts: 878 Drives: '11 370Z SPT 6MT BLK Rep Power: 25	For those that aren't following FI on Facebook (https://www.facebook.com/FastIntentions) Tony just posted a picture of the car strapped down on the dyno.

02-08-2013, 01:53 AM	#293 (permalink)
DEpointfive0 Premium Member Bitches Join Date: Jan 2012 Location: SoCal Posts: 14,824 Drives: a lot Rep Power: 17151	With stock cats, congrats brother, when do you need my 7AT?!?!?!

02-08-2013, 02:38 AM	#296 (permalink)
G37Sam A True Z Fanatic Join Date: Dec 2008 Location: Dubai, UAE Posts: 1,507 Drives: RB'd G37 Rep Power: 20	Congrats Tony! These are some sick numbers! F.I. Inc. likes this. __________________ '14 Viper GTS '08 RB'd G37S - Sold

02-08-2013, 02:54 AM	#297 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	Update, No 3" tonight. Got shut down by Johnny law. Too much noise, too late in the evening. Will get back at it tomorrow. As of now it looks like we are going to make the track Saturday! Stay tuned... Thanks and goodnight. Tony TerribleONE, XwChriswX, ts-c63 and 3 others like this. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION" Last edited by F.I. Inc.; 02-08-2013 at 03:50 AM.

02-08-2013, 03:13 AM	#298 (permalink)
blackonorange A True Z Fanatic Join Date: Jul 2011 Location: Saskatchewan Posts: 1,078 Drives: 09 370z Rep Power: 16	What fuel pressure gauge do you have ?

02-08-2013, 03:31 AM	#299 (permalink)
asdfsammich Enthusiast Member Join Date: Dec 2011 Location: Southern California Posts: 456 Drives: 09 370Z SR MT Rep Power: 13	Damn! This is a hell of a good show! Tapatalk & such etc TerribleONE and DEpointfive0 like this.

02-08-2013, 04:05 AM	#300 (permalink)
TerribleONE A True Z Fanatic Join Date: Jan 2009 Location: Socal Posts: 10,203 Drives: WOT Rep Power: 5850	Had a great day today Tony. You guys continue to surpass my expectations. Cant wait for tomorrow and saturday. __________________ 638WHP 541WTQ @ 13.5PSI Build thread

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fast Intentions 3" (Twin Turbo) exhaust is here!	F.I. Inc.	Intake/Exhaust	91	02-08-2017 06:09 AM
Fast Intentions "Twin Turbo Kit" Official Release	F.I. Inc.	Drivetrain/Engine	95	11-20-2014 12:38 AM
Twin Turbo vs. Single Turbo V6: A Dissertation	Mike@GTM	Forced Induction	115	08-14-2014 10:04 PM
Twin scroll vs twin turbo	SS_Firehawk	Forced Induction	32	04-13-2014 01:02 PM
GTM Motorsports Twin Turbo vs Greddy Twin Turbo Kit	Nismo221	Forced Induction	57	08-16-2011 05:44 PM

*****Fast Intentions "Twin Turbo Kit" is here*****

Fast Intentions "Twin Turbo Kit" is here